Extron WallVault Digital System User manual

Brand: Extron

Model: WallVault Digital System

Type: User manual

Quick Reference

PoleVault

Digital Classroom AV Systems with MediaLink Plus 100 Controller

Easy to Use Control Panel Connecting to the System

Display Power

ON: Press this button to turn on

the main display. You may not see

an image immediately after the

button is pressed, as many

projectors need to warm up for

30-90 seconds. Button may blink

as the projector warms up.

OFF: Press the button to turn off

the display. Button may blink as

the projector cools down.

Volume Knob

Rotate knob counterclockwise to

lower volume and clockwise to

raise the volume.

The LEDs indicate the volume

level.

Input/Function Buttons

These buttons select the source for the main

projector or display, or perform the labeled function.

MLC Plus 100

NOTE: Controller buttons may be designated for other functions. Please contact your AV

Technician for details.

PVT HD RGB Input Wallplate

PVT HDMI Input Wallplate

Computer Video and Stereo Audio

This type of input is commonly used to

connect a computer, laptop, or document

camera to the system.

Use the VGA and stereo

audio cable like the one

shown here to connect

your computer or

document camera

to the wallplate.

HDMI Video and Audio

This type of input is commonly used to

connect a newer laptop, tablet, Blu-ray

player, Apple TV, or tuner to the system.

In many cases, source devices

transmit both digital video and

audio on a single HDMI cable.

If your device does not

“embed” audio on the

HDMI signal, a 3.5 mm

analog audio cable may

be used for the Audio In

connection above the HDMI connector.

Power LED

Input wallplates provide a Power LED for

each input. Amber indicates that the input

is powered, but it is not selected or no

source signal is present. Green indicates

that the input is powered, selected, and a

source signal is present.

Technical Support

Phone: Email:

68-3576-01 Rev. A

07 20

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

Quick Reference

VoiceLift

Pro Microphone System

The microphone is automatically powered

on once it is removed from the charging

base. To power the microphone on

manually, press and hold the power button

until the status LED illuminates. The LINK

LED on the VLR 302 receiver illuminates

green to indicate the microphone is

connected. A Red LED on the microphone

while in use indicates the battery is low.

~ 6

Adjust each side of the lanyard to

the appropriate length and place the

microphone around your neck so that it

hangs approximately six inches below your

chin. Speak in a normal tone of voice.

At the end of the day, return the

microphone to the charging base. The

status LED on the microphone changes

from Red to Green to signify when the

microphone is fully charged.

VoiceLift Pro Microphones

VoiceLift Pro works with the room AV system to evenly distribute instructor

and student voices throughout the room. Both pendant and handheld

versions of the microphone are available and up to two microphones may be

used simultaneously.

VoiceLift Pro microphones use digital RF technology for transmitting voice to

the receiver.

Volume Control

The microphone amplies your voice above

ambient room noise. Adjust the volume level, if

necessary, by pressing the Volume Up and Down

buttons on the side.

Instant Alert

If your classroom system is equipped with Instant

Alert capability, press and hold both volume

buttons for three seconds, until the status LED

ashes Red, to initiate.

Charging

To ensure operation for the entire

day, charge the microphone

batteries every night for at least

ve hours.

Only NiMh batteries are

supported for charging.

Do not attempt to charge

alkaline batteries.

While in the charger, a Red LED

on the microphone means the

battery is charging. Green

means the battery is fully

charged. Flashing Red, then

Green means an alkaline or

damaged battery is detected.

POWER

AUDIO IN

Aux Microphone Input

Auxiliary input for lavalier

or lapel microphone

Volume Adjustment

Volume level controls

are conveniently

located on the

microphone.

LED Indicator

Status LED indicates

when the

microphone is on

or charging.

LED Indicator

Status LED indicates

when the microphone

is on or charging.

Wireless Transmission

Wirelessly transmit the

presenter’s voice to the receiver.

Power/Mute

Power button also

serves to mute sound

for privacy.

A ashing green LED

indicates the micro-

phone is muted. Press

and release the power

button to mute or

unmute.

Power/Mute

Power switch also

serves to mute

sound for privacy.

Extron WallVault Digital System User manual

Extron WallVault Digital System User manual

Extron WallVault Digital System User manual

Related papers

Other documents