Norac 7465BC-JD-LP Installation guide

  • Hello! I've reviewed the Severe Terrain Option Low Profile Brackets Installation Manual by NORAC and I am ready to assist you with any questions you may have about its contents. This document covers the detailed installation of the low-profile brackets, including the mounting of ultrasonic sensors, electrical connections, and software setup. I can provide information on the mounting guidelines, recommended sensor arrangements, and important electrical installation steps as described in the manual.
  • What type of grease should be used on threaded parts?
    Is dielectric grease recommended on NORAC electrical connections?
    What is the minimum distance the sensor must be from the ground in its lowest position?

SevereTerrainOption
LowProfileBrackets‐JohnDeere
InstallationManual
Copyright2023byNORACSystemsInternationalInc.
ReorderP/N:7465BCJDLPINSTRevB(SevereTerrainOptionLowProfileBracketsJohnDeere)
NOTICE:NORACSystemsInternationalInc.reservestherighttoimproveproductsandtheirspecificationswithoutnoticeandwithouttherequirementtoupdate
productssoldpreviously.Everyefforthasbeenmadetoensuretheaccuracyoftheinformationcontainedinthismanual.Thetechnicalinformationinthismanual
wasreviewedatthetimeofapprovalforpublication.
WWW.NORAC.CA
PRECISIONDEFINED
Contents
1
Introduction..........................................................................................................................1
2
PartsOverview......................................................................................................................2
3
UltrasonicSensorInstallation................................................................................................4
4
ElectricalInstallation.............................................................................................................8
5
SoftwareSetup......................................................................................................................9
6
CableDrawings....................................................................................................................10

WWW.NORAC.CA
PRECISIONDEFINED

Page1
Visitwww.solutions.norac.caformoresystem
installationandtroubleshootinginfo.
1 Introduction
Pleasetakethetimetoreadthismanualcompletelybeforeattemptingtoinstallthesystem.Athorough
understandingofthismanualwillensurethatyoureceivethemaximumbenefitfromthesystem.
Yourinputcanhelpmakeusbetter!Ifyoufindissuesorhavesuggestionsregardingthepartslistorthe
installationprocedure,pleasedon’thesitatetocontactus.
Everyefforthasbeenmadetoensuretheaccuracyoftheinformationcontainedinthismanual.Allparts
suppliedareselectedtospeciallyfitthesprayertofacilitateacompleteinstallation.However,NORACcannot
guaranteeallpartsfitasintendedduetothevariationsofthesprayerbythemanufacturer.
Pleasereadthismanualinitsentiretybeforeattemptinginstallation.
Donotusehighspeedpowertools/drillswheninstallinghardware.
TheuseofdielectricgreaseisnotrecommendedonanyNORACelectricalconnections.
ToensureallstainlesssteelhardwaredoesnotgallorseizeapplyalightcoatingofthesuppliedPermatex
Antiseizegreasetoallthreadedpartsuponinstallation.PermatexAntiseizelubricantispreferred,butother
similarantiseizeproductsmaybeused.
WWW.NORAC.CA
PRECISIONDEFINED

Page2
Visitwww.solutions.norac.caformoresystem
installationandtroubleshootinginfo.
2 PartsOverview
2.1. KitOverview
Figure1:SevereTerrainParts
WWW.NORAC.CA
PRECISIONDEFINED

Page3
Visitwww.solutions.norac.caformoresystem
installationandtroubleshootinginfo.
2.2. ListofParts
ItemPartNumberNameQuantity
B054470601KITCABLETIEBLACK10PCS21IN150PCS7.5IN1
B12105835CLAMPEXHAUST21/4INSS4
B2044971SENSORMOUNTINGBRACKETLOWPROFILE16GA2
C064321010CABLENETWORK18AWG10M2
E0750300MAXSENSOR2
E1043760NETWORKCOUPLER3WAY2
M027465BCJDLPINSTMANUALINSTALLATIONSEVERETERRAINOPTIONLOWPROFILE‐JOHNDEERE1
WWW.NORAC.CA
PRECISIONDEFINED

Page4
Visitwww.solutions.norac.caformoresystem
installationandtroubleshootinginfo.
3 UltrasonicSensorInstallation
3.1. UltrasonicSensorSerialNumberArrangement
Wheninstallingtheultrasonicsensors,startwiththesmallestserialnumberonthelefthandside,andproceed
tothelargestserialnumberontherighthandside.Eachultrasonicsensorhasaserialnumberstampedonthe
sensorhousing.
ApplyalightcoatingofthesuppliedPermatexAntiseizegreasetoallthreadedpartsuponinstallation.
Figure2:SensorSerialNumberArrangement
 Onlythecomponentsshowninblackareincludedinthiskit.
WWW.NORAC.CA
PRECISIONDEFINED

Page5
Visitwww.solutions.norac.caformoresystem
installationandtroubleshootinginfo.
3.2. WingSensorInstallation
1. Thesensorbracketshouldbeorientedforward(aheadoftheboom).
2. Mountthesensorbracketsontotheboomhalfwaybetweenthetipandcenterofthesprayer.
3. MounttheNORACultrasonicsensorintothesensorbracket.TorquetheM8nutto108inlb(12Nm).Run
thesensorcableeitherthroughholeinthebackorthroughthesidecutoutandbehindthebracket.Ensure
thecableisclearofmovingpartsandwillnotbedamagedduringfolding.
 
Figure3:BracketMountingExample
4. Exhaustclamps(B12)canbeusedifmountingthesensorbracketstoaportionoftheboomwithround
tubing.
 
Figure4:BracketMountedwithExhaustClamps(B12)
Front
Front
WWW.NORAC.CA
PRECISIONDEFINED

Page6
Visitwww.solutions.norac.caformoresystem
installationandtroubleshootinginfo.
3.3. UltrasonicSensorMountingGuidelines
Thefollowingguidelineswillensureoptimalsensorperformanceandpreventsensormeasurement.
1. Initslowestposition,thesensormustbe9inches(230mm)ormorefromtheground.
2. Ensurethattherearenoobstructionswithina12inch(300mm)diametercircleprojecteddirectlybelow
thecenterofthesensor.
3. Thesensorshouldbeapproximatelyverticalatnormaloperatingheights.
Figure5:SensorMountingGuidelines
Figure6:BracketMountingGuidelines
WWW.NORAC.CA
PRECISIONDEFINED

Page7
Visitwww.solutions.norac.caformoresystem
installationandtroubleshootinginfo.
3.4. LowProfileBracketMountingGuidelines
1. Minimizethedistancebetweentheboltstopreventbendingthebracketandpreventthebracketfrom
looseningovertime.
2. Ensurethebracketismountedtightagainstthebottomoftheboom,minimizingthedistancebetweenthe
boomstructureandtheangledflange.
Aproblemcanariseifasensorisnotmountedcorrectly.Thismayonlybecomeapparentoncethecontrol
systemisswitchedfromsoiltocropmode.
Becarefulthatthesensorbracketdoesnotcollidewithanyotherpartoftheboomwhentheboomisfolded
totransportposition.Ifpossible,mountthesensorbracketswhiletheboomsarefoldedtoensuretheywill
notcauseinterference.
WWW.NORAC.CA
PRECISIONDEFINED

Page8
Visitwww.solutions.norac.caformoresystem
installationandtroubleshootinginfo.
4 ElectricalInstallation
1. Removethe2waycouplerwithterminator(E20)fromtheoutersensorandinstallitattheinnersensor.
2. Installthe3waycoupler(E10)attheoutersensor.PlugtheexistingCANbuscable(C05)andthesensor
cableintothe3waycoupler.
3. ConnecttheCANbuscable(C06)betweenthe2waycouplerwithterminator(E20)andthe3waycoupler
(E10).
Onlythecomponentsshowninblackareincludedinthiskit.
Figure7:ElectricalInstallation

WWW.NORAC.CA
PRECISIONDEFINED

Page9
Visitwww.solutions.norac.caformoresystem
installationandtroubleshootinginfo.
5 SoftwareSetup
1. Startupthesprayerandtestthesprayer’sfunctionality.Thecontrolpaneldoesnotneedtobepowered
onfortheoriginalswitchestofunction.
Confirmthatthecablingandhosesareagreeabletotheentirerangeofmotion.
2. Ifanyfunctionsdonotwork,reviewthismanualtocheckforproperinstallation.
3. Turnonthepowerforthecontrolpanelusingtheswitchonthesideofthechassis.
4. RefertotheSprayHeightControlOperator’sManualtorunanautomaticinstall.
WWW.NORAC.CA
PRECISIONDEFINED

Page10
Visitwww.solutions.norac.caformoresystem
installationandtroubleshootinginfo.
6 CableDrawings
6.1. ITEMC06:4321010‐CABLENETWORK18AWG‐10M

WWW.NORAC.CA
PRECISIONDEFINED

Page11
Visitwww.solutions.norac.caformoresystem
installationandtroubleshootinginfo.
 Notes
TOPCONAgricultureCanada
3702KinnearPlace
Saskatoon,SKS7P0A6
TOPCONAgricultureAmericas
W5527Hwy106
FortAtkinson,WI53538
TOPCONPrecisionAgricultureEurope
Avenidadelaindustria,
35,TresCantos,España
Spain
Support
Phone:8889799509
Email:[email protected]
Web:www.norac.ca

/