anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED:
Step-by-Step Installation Sequence
!
Hammer
Pencil
Wire Brush
Level Hammer Drill
Safety Glasses
Installation Instructions
Screens and Panels - Surface Mounted Privacy Screens
Masonry Drill Bit Set
1/4", and 5/8"
5/8" Wrench
Product requires assembly before installation.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a
3,000 psi minimum and be cured for at least 28 days prior to the installation of the bench.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
Installation Instructions
Step-by-Step Installation Sequence
1.
2.
3.
5.
4.
Evacuate debris from mounting holes using compressed air and a steel wire
brush. This will create a clean environment for the anchor system.
!
24
Locate an anchor and adjust the nut so it is ush with the top of the anchor to
protect the threads from being damaged. Insert the anchor into the hole.
Use the hammer to x the anchor into the drilled hole by giving it several
hammer blows.
6.
7.
Repeat steps 2 - 5 until all anchors are installed.
8.
!
5
Screens and Panels - Surface Mounted Privacy Screens
Care should be given to avoid rubbing the powder coating o the foot. A
rubber washer is a suitable replacement option. Mount the post to the ground
by placing a washer and a nut onto each anchor. Leave the hardware nger
tight until all of them have been installed. Verify that the post is level before
tightening the anchors. Tighten all of the hardware with a wrench.
Remove the nuts and washers o of the anchors. Align the mounting holes of
the stanchion over top of the anchors and slide it down into place.
It is recommended that you start holes in sequential order from the
smaller to the larger drill bits to avoid oversized holes or holes drilled too
deep. Begin with 1/4" diameter drill bit followed by the 5/8" diameter bit.
Place stanchion in the desired location. Mark the location of the holes with
a pencil. To verify the alignment of the anchor markings you may reference
page 3.
8a 8b
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
Manufactured in the U.S.
Installation Instructions
Copyright 2021 ANOVA®
Screens and Panels - Surface Mounted Privacy Screens
10/18/2021
FOOT MOUNTS:
4FT FOOTPRINT:
6FT FOOTPRINT:
8FT FOOTPRINT:
AA
54.00
6.00
6.00
.64
(8 PLCS)
SECTION A-A
AA
78.00
6.00
6.00
.64
(8 PLCS)
SECTION A-A
SCALE 1 : 5
AA
102.00
6.00
6.00
.64
(8 PLCS)
SECTION A-A
SCALE 1 : 6.5
Installation Instructions
Screens and Panels - Surface Mounted Privacy Screens
Inspect the shipping container contents for damage and to
determine that all components and hardware are present.
1.
2. Lay all parts on a so work surface or on the shipping
packaging to prevent damage to nish.
NOTE: Before assembling the nuts to the bolts, it is
recommended that a light oil or petroleum jelly be applied
to the screw threads.
COMPONENT PARTS:
ASSEMBLY HARDWARE: All hardware is stainless steel.
ASSEMBLY:
anovafurnishings.com
888.535.5005 tel
Surface Mount Post(s) Panel(s)
1/4"-20 Stainless Steel
Cap Nut(s)
5/16" Stainless Steel
Flat Washer
5" Stainless Steel
Stud Anchor
1/4"-20 Stainless Steel
Carriage Bolt(s)
TOOLS NEEDED:
• 9/16" Wrench or Socket
• 7/16" Wrench or Socket
•
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
Manufactured in the U.S.
Copyright 2021 ANOVA®10/18/2021
Carriage Bolt
Replacement Parts
Flat Washer
Cap nut
3. Once the Posts are secured to the ground, locate two
Carriage Bolts, two Washers, and two Cap Nuts. Attach the
Panel to one post by using the inserting a Carriage bolt rst
through the top square hole on either end of the Panel,
then through the Post's bracket.
Secure the Carriage Bolt on the back side of the bracket by
inserting on a Washer followed by a Cap nut.
Repeat this process on the top square hole on the opposite
end of the Panel.
Repeat for all remaining mounting holes on the Panel.
Posts
Panel
/
