anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED:
• 5/32" Allen Wrench
• or Hex Head Socket
• with Extension
Assembly/Installation Instructions
Canyon Edge
CE18C18T/R- Canyon Edge 18' Radius Curved Bench
CE18C26T/R- Canyon Edge 26' Radius Curved Bench
CE18J90T/R- Canyon Edge Gabion-Style 4' Corner Bench
CE1815- Canyon Edge Steel Gabion-Style 15" Accent Section
CE1848T/R- Canyon Edge Gabion-Style 4' Linear Bench
CE1860T/R- Canyon Edge Gabion-Style 5' Linear Bench
CE1872T/R- Canyon Edge Gabion-Style 6' Linear Bench
ASSEMBLY:
Inspect the shipping container contents for damage and to
determine that all components and hardware are present.
1.
Using a 5/32" Allen Wrench or Hex Head Socket with
Extension, loosen the 1/4"-20 x 1" hex drive screws
between the top wood planks or metal slats upward about
1/8", as shown:
2.
Slide the top plate to align the bolt head over the larger
section of the keyslot as shown:
3.
1
CE1872RCE1815CE18C18T
2
Li o the top plate, setting it aside on a so work surface
or on the shipping packaging to prevent damage to the
product's nish.
4.
CAUTION: At this point if you plan to anchor the section, please proceed to Step 5. If you are not
planning to anchor the sections, then please proceed to Step 13.
TOOLS NEEDED: HARDWARE NEEDED:
Step-by-Step Installation Sequence
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a
3,000 psi minimum and be cured for at least 28 days prior to the installation of the bench.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
FOOT MOUNTS:
CE1848T and CE1848RCE1815
!
!
(4 ) 3/8" x 3.5" 18-8
Stainless Steel Stud Anchors
92188A202
Optional: (4) 3/8"
Rubber Washers
90130A050Hammer Drill
Masonry Drill Bit Set
3/16", and 3/8"
Hammer
Pencil
9/16"Wrench
Wire Brush
Level
Safety Glasses
AA
20.6875
35.0000
SECTION A-A
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
NOTES:
STUD SHOULD BE FLUSH WITH THE FACE OF THE PANEL.
DRAIN HOLES FACE DOWNWARDS
BREAK ALL SHARP EDGES
ALL PARTS LOCATED BY MORTISE AND TENON
CLEAN UP ALL WELDS AND SPATTER
PER NORMAL POWDER-COATED
PART STANDARDS
GRIND ALL BLISTERS
REVISIONS
REV.
DESCRIPTION
ECN TR #
DATE
001
ORIGINAL PRINT
NONE
Canyon Edge 4' Linear Bench w/ Thermory
001
CE1848T
SHEET 1 OF 1
1:5
2/17/2021
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
A A
B B
4
4
3
3
2
2
1
1
SCALE
35.00"
20.70"
BB
20.7475
13.0000
SECTION B-B
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
NOTES:
STUD SHOULD BE FLUSH WITH THE FACE OF THE PANEL.
DRAIN HOLES FACE DOWNWARDS
BREAK ALL SHARP EDGES
ALL PARTS LOCATED BY MORTISE AND TENON
CLEAN UP ALL WELDS AND SPATTER
PER NORMAL POWDER-COATED
PART STANDARDS
GRIND ALL BLISTERS
REVISIONS
REV.
DESCRIPTION
ECN TR #
DATE
001
ORIGINAL PRINT
NONE
Canyon Edge 15" Accent Section
001
CE1815
SHEET 1 OF 1
1:5
2/17/2021
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
A A
B B
4
4
3
3
2
2
1
1
SCALE
20.70"
13.00"
3
BB
45.38
20.75
20.75
11.23
10.37
11.23
23.77
10.37
22.75
22.63
10.38
10.37
13.39
13.39
SECTION B-B
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
NOTES:
STUD SHOULD BE FLUSH WITH THE FACE OF THE PANEL.
DRAIN HOLES FACE DOWNWARDS
BREAK ALL SHARP EDGES
ALL PARTS LOCATED BY MORTISE AND TENON
CLEAN UP ALL WELDS AND SPATTER
PER NORMAL POWDER-COATED
PART STANDARDS
GRIND ALL BLISTERS
REVISIONS
REV.
DESCRIPTION
ECN TR #
DATE
001
ORIGINAL PRINT
NONE
Canyon Edge 4' Corner Bench w/ Thermory
001
CE18J90T
SHEET 1 OF 1
1:6.5
2/17/2021
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
SCALE
A A
B B
4
4
3
3
2
2
1
1
CC
20.6875
59.0000
SECTION C-C
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
NOTES:
STUD SHOULD BE FLUSH WITH THE FACE OF THE PANEL.
DRAIN HOLES FACE DOWNWARDS
BREAK ALL SHARP EDGES
ALL PARTS LOCATED BY MORTISE AND TENON
CLEAN UP ALL WELDS AND SPATTER
PER NORMAL POWDER-COATED
PART STANDARDS
GRIND ALL BLISTERS
REVISIONS
REV.
DESCRIPTION
ECN TR #
DATE
001
ORIGINAL PRINT
NONE
Canyon Edge 6' Linear Bench w/ Thermory
001
CE1872T
SHEET 1 OF 1
1:5
2/17/2021
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
A A
B B
4
4
3
3
2
2
1
1
SCALE
BB
20.6875
46.0000
SECTION B-B
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
NOTES:
STUD SHOULD BE FLUSH WITH THE FACE OF THE PANEL.
DRAIN HOLES FACE DOWNWARDS
BREAK ALL SHARP EDGES
ALL PARTS LOCATED BY MORTISE AND TENON
CLEAN UP ALL WELDS AND SPATTER
PER NORMAL POWDER-COATED
PART STANDARDS
GRIND ALL BLISTERS
REVISIONS
REV.
DESCRIPTION
ECN TR #
DATE
001 ORIGINAL PRINT
NONE
Canyon Edge 5' Linear Bench w/ Thermory
001
CE1860T
SHEET 1 OF 1
1:5
2/17/2021
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
A A
B B
4
4
3
3
2
2
1
1
SCALE
CE1860T and CE1860R
CE1872T and CE1872R
CE18J90T and CE18J90R
46.00"
59.00"
11.23" 10.37"
10.37"
10.37"
13.39"
13.39"
20.75"
20.75"
10.38"
45.38"
11.23"
22.75"
23.77"
22.63"
20.70"
20.70"
4
BB
20.66
31.60
28.54
20.66
SECTION B-B
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
NOTES:
STUD SHOULD BE FLUSH WITH THE FACE OF THE PANEL.
DRAIN HOLES FACE DOWNWARDS
BREAK ALL SHARP EDGES
ALL PARTS LOCATED BY MORTISE AND TENON
CLEAN UP ALL WELDS AND SPATTER
PER NORMAL POWDER-COATED
PART STANDARDS
GRIND ALL BLISTERS
REVISIONS
REV.
DESCRIPTION
ECN TR #
DATE
001
ORIGINAL PRINT
NONE
001
CE18C18T-CENTERED
SHEET 1 OF 1
1:6
2/17/2021
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
SCALE
A A
B B
4
4
3
3
2
2
1
1
BB
20.7239
27.6313
29.6110
20.7239
SECTION B-B
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
NOTES:
STUD SHOULD BE FLUSH WITH THE FACE OF THE PANEL.
DRAIN HOLES FACE DOWNWARDS
BREAK ALL SHARP EDGES
ALL PARTS LOCATED BY MORTISE AND TENON
CLEAN UP ALL WELDS AND SPATTER
PER NORMAL POWDER-COATED
PART STANDARDS
GRIND ALL BLISTERS
REVISIONS
REV.
DESCRIPTION
ECN TR #
DATE
001
ORIGINAL PRINT
NONE
001
CE18C26T-CENTERED
SHEET 1 OF 1
1:6
2/17/2021
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
SCALE
A A
B B
4
4
3
3
2
2
1
1
CE18C18T and CE18C18R
CE18C26T and CE18C26R
31.60"
20.72" 20.72"
27.63"
29.61"
28.54"
20.66" 20.66"
Place bench section in the desired location. Mark the location of the
holes with a pencil.
5.
Evacuate debris from mounting holes using compressed air and a steel
wire brush. This will create a clean environment for the anchor system.
7.
Locate an anchor and adjust the nut so it is ush with the top of the
anchor to protect the threads from being damaged. Insert the anchor
into the hole.
8.
It is recommended that you start holes in sequential order from the
smaller to the larger drill bits to avoid oversized holes or holes drilled
too deep. Begin with 3/16" diameter drill bit followed by the 3/8"
diameter bit.
6.
!
57
5
Use the hammer to x the anchor into the drilled hole by giving it
several hammer blows.
9.
Repeat steps 5-9 until all anchors are installed.10.
Remove both the nuts and washers o of each anchor. Align the
mounting holes of the bench section over top of the anchors and slide it
down into place.
11.
Care should be given when lling the cage. It is recommended that ller
be hand-placed to avoid damaging the cage.
13.
Locate the top plate and lower it onto the bench section's frame, taking
care to avoid damging the nish.
14.
Slide the top plate to align the bolt head over the smaller section of the
keyslot to prevent the top plate from being lied. Using a 5/32" Allen
Wrench or Hex Head Socket with Extension, tighten the previously-
loosened 1/4"-20 x 1" hex drive screws between the top wood planks or
metal slats.
15.
Care should be given to avoid rubbing the powder coating o of the
frame or mesh panels. A 3/8" rubber washer is a suitable replacement
option. Mount the bench section to the ground by placing a washer
and a nut onto each anchor. Leave the hardware nger-tight until all of
them have been installed. Verify that the bench section is level before
tightening the anchors. Tighten all of the hardware with a wrench.
12.
9 11
!
12.1
12.2
Manufactured in the U.S. 6
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
Copyright 2021 ANOVA®02/19/2021
Assembly and Replacement Parts
Top Plate
Front Panel
Side Panel
-
1
-
2
-
3
-
4
-
5
-
6
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Anova RLA60R Installation guide
-
-
-
-
-
-
-
-
-
