Anova A2376 Installation guide

Anova
Brand
Anova
Model
A2376
Type
Installation guide

Here is some more information on your Anova A2376 Kit:

  • The kit includes easy-to-assemble surface mount mounting brackets for your picnic table.
  • The mounting brackets are made of durable steel and are designed to withstand the elements.
  • The kit comes with all the necessary hardware, including stainless steel stud anchors and washers.
  • The brackets are easy to install. All you need is a pencil, safety glasses, masonry drill bit set (3/16" and 3/8"), wire brush, hammer, level, hammer drill, and a 9/16" wrench.
  • The kit is compatible with all picnic tables with a 2.38" OD steel tube.
  • The brackets can be used to mount your picnic table to a concrete footing or slab.

Here is some more information on your Anova A2376 Kit:

  • The kit includes easy-to-assemble surface mount mounting brackets for your picnic table.
  • The mounting brackets are made of durable steel and are designed to withstand the elements.
  • The kit comes with all the necessary hardware, including stainless steel stud anchors and washers.
  • The brackets are easy to install. All you need is a pencil, safety glasses, masonry drill bit set (3/16" and 3/8"), wire brush, hammer, level, hammer drill, and a 9/16" wrench.
  • The kit is compatible with all picnic tables with a 2.38" OD steel tube.
  • The brackets can be used to mount your picnic table to a concrete footing or slab.
anovafurnishings.com
888.535.5005 tel
Installation Instructions
TOOLS NEEDED: HARDWARE NEEDED:
Step-by-Step Installation Sequence
Product requires assembly before installation.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a 3,000 psi
minimum and be cured for at least 28 days prior to the installation of the table.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
!
Hammer DrillHammer
Pencil
Wire Brush
Level
Safety Glasses
Picnic Tables using the A2376 Kit
9/16"Wrench
Masonry Drill Bit Set
3/16" and 3/8"
Optional: (4) 3/8"
Rubber Washers
90130A050
(4) 3/8" x 3.5" 18-8
Stainless Steel Stud Anchors
92188A202
Instructions apply to all Picnic Tables with a 2.38" OD steel tube.
A2374 KIT:
(2) Surface Mount
Mounting Brackets
Installation Instructions
Step-by-Step Installation Sequence
2.
3.
5.
4.
Evacuate debris from mounting holes using compressed air and a steel wire brush.
This will create a clean environment for the anchor system.
!
2
Locate an anchor and adjust the nut so it is ush with the top of the anchor to
protect the threads from being damaged. Insert the anchor into the hole.
Use the hammer to x the anchor into the drilled hole by giving it several hammer
blows.
6.
7.
Repeat steps 2 - 5 until all anchors are installed.
8.
!
Place table in the desired location. Mark the location of the holes with a pencil. To
verify the alignment of the anchor markings you may reference page 3.
5
4
Remove the nuts and washers o of the anchors. Place the table frame so it is
centered between two anchors on both sides. Reference image 9 at the bottom of
the page for additional clarity. The brackets line up with the vertical tubing, but on
opposite sides to prevent any kind of movement.
Care should be given to avoid rubbing the powder coating o the bracket.
A 3/8" rubber washer is a suitable replacement option. Mount the table to the
ground by placing a washer and a nut onto each anchor. Leave the hardware
nger tight until all of them have been installed. Verify that the table is level before
tightening the anchors. Tighten all of the hardware with a 9/16" wrench.
It is recommended that you start holes in sequential order from the smaller to
the larger drill bits to avoid oversized holes or holes drilled too deep. Begin with a
3/16" diameter drill bit followed by a 3/8" diameter bit.
Picnic Tables using the A2376 Kit
7
9
8b8a
Table length may vary
Installation Instructions
FOOT MOUNTS:
• Furniture must not be used other than for its intended purpose and should be inspected regularly for loose, missing, or
broken hardware, and general instability
• Furniture that is damaged or appears to be unstable must be removed from service and repaired or replaced
• Repairs must be made using only factory authorized parts and methods.
WARNING
• Do not drag the assembled unit across any surface.
• This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to remove surface
dirt. Do not clean with a solvent or petroleum based products.
CARE AND
MAINTENANCE
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
12/06/2022 Copyright 2022 Anova ® Manufactured in the U.S.
Picnic Tables using the A2376 Kit
FOOT MOUNT CHART
- FOOT MOUNT 1
Sku #s Length
D2003
D2003COM
F2003
F2008
L2003
52.73"
D2014
F2010
F2014
F6420
68.53"
SECTION A-A
SCALE 1 / 20
A A
1
1
2
2
A A
B B
1
001
OF
F2014
1
REV
SHEET1 / 20
SCALE
DATE 2/6/2019
DWG NO
TITLE
A
DRAWN D. METZ
SIZE
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125
.0625 DURING COATING.
TOLERANCES UNLESS NOTED:
X
1 X.X
.5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX
.015625 ANGULAR ± 1°
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
specify@anovafurnishings.com
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
NOTES:
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
REV DESCRIPTION ECN TR.# DATE
001 02/06/19
68.53 4.44
.44
(4 PLCS)
12.63
12.63"
Length 4.44"
Ø.44"
(4 PLCS)
FOOT MOUNT 1
SECTION A-A
SCALE 1 / 11
A A
1
1
2
2
3
3
4
4
A A
B B
C C
D D
SHEET
1
OF
1
DRAWN
CHECKED
QA
MFG
APPROVED
lindsey 3/11/2009
DWG NO
F2173SPEC
TITLE
SIZE
C
SCALE
REV
120.00
99.28 10.33
2.38 OD
64.00
30.00
28.88
19.40
10.00
1.90
1.90
92.47
4.44
(2 PLCS)
.44
(4 PLCS)
12.63
F2173 & F6415
4.44"
(2 PLCS)
12.63"
Ø.44"
(4 PLCS)
92.47"
F2022
AA
12.63
4.44 84.17
.44
SECTION A-A
  • Page 1 1
  • Page 2 2
  • Page 3 3

Anova A2376 Installation guide

Anova
Brand
Anova
Model
A2376
Type
Installation guide

Here is some more information on your Anova A2376 Kit:

  • The kit includes easy-to-assemble surface mount mounting brackets for your picnic table.
  • The mounting brackets are made of durable steel and are designed to withstand the elements.
  • The kit comes with all the necessary hardware, including stainless steel stud anchors and washers.
  • The brackets are easy to install. All you need is a pencil, safety glasses, masonry drill bit set (3/16" and 3/8"), wire brush, hammer, level, hammer drill, and a 9/16" wrench.
  • The kit is compatible with all picnic tables with a 2.38" OD steel tube.
  • The brackets can be used to mount your picnic table to a concrete footing or slab.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents