H3C LSPM1XP1P User manual

Brand: H3C

Model: LSPM1XP1P

Type: User manual

This manual is also suitable for

H3C CX4&XFP Interface Cards

User Manual-V1.03

Introduction to CX4&XFP interface cards

Overview

Table 1 CX4&XFP interface cards brief introduction

Model Description

LSPM1CX2P

Each LSPM1CX2P interface card provides

two 10 Gbps copper ports.

LSPM1XP2P

Each LSPM1XP2P interface card provides

two 10 Gbps XFP fiber ports.

LSPM1XP1P

Each LSPM1XP1P interface card provides

one 10 Gbps XFP fiber port.

Note:

The CX4 and XFP interface cards are applicable to multiple

models of H3C switches, and the switch models that each

of them applies to may update with time. For the latest

information, contact H3C technical support or marketing

staff.

LSPM1CX2P

Appearance of the interface card

Figure 1 Front panel of the LSPM1CX2P interface card

Description of LSPM1CX2P

Each LSPM1CX2P interface card provides two 10 Gbps copper

ports and supports CX4 standards. You can connect a CX4 port to

another CX4 port through a CX4 cable provided by H3C. For more

information about the supported CX4 cables, see Table 2

. The

supported max transmission distance is 3 m (9.84 ft), which is only

suitable for short-haul transmission.

Table 2 CX4 cables supported by LSPM1CX2P

Cable Connector Cable length

LSPM2STKA 0.5m (19.69 in.)

LSPM2STKB 1m (39.37 in.)

LSPM2STKC

4X Infiniband

3m (118.11 in.)

Note:

H3C recommends that you use CX4 cables of H3C on the

LSPM1CX2P.

The types of CX4 cables may update with time. For

information about them, contact H3C technical support or

marketing staff.

Description of LEDs

There is an LED for each port on the panel of the interface card.

Table 3 Description of LEDs on the LSPM1CX2P

LED Status Description

The port is normally connected.

The LED blinks quickly when the

port is sending or receiving data.

Port LED of the

LSPM1CX2P

interface card

Off The port is not up.

Note:

Port LED of the LSPM1CX2P interface card is not affected

by the port mode switching button on your switch. For

more information about the port mode switching button,

see the installation guide of the switch.

LSPM1XP2P

Appearance of the interface card

Figure 2 Front panel of the LSPM1XP2P interface card

Description of LSPM1XP2P

Each LSPM1XP2P interface card provides two 10-Gigabit XFP

fiber ports. You can insert an XFP transceiver module into the port to

connect it to another XFP port through an optical fiber. For more

information about the supported XFP transceiver modules and fibers,

see Table 4

Table 4 XFP transceivers modules and fibers supported by

LSPM1XP2P

Transceiver

Central

wavele

ngth

Con

nect

Interface

fiber

Max

transmiss

ion

distance

50/125 µm

multimode

optical fiber

300m

(984.25

ft.)

XFP-SX-MM

850

850 nm

62.5/125 µm

multimode

optical fiber

33m

(108.27

ft.)

XFP-LX-SM

1310

10km

(6.21 mi.)

XFP-LH40-S

M1550-F1

1550

40km

(24.85 mi.)

XFP-LH80-S

M1550

1550

9/125 µm

single mode

optical fiber

80km

(49.71 mi.)

Note:

H3C recommends that you use XFP transceiver modules

of H3C on the LSPM1XP2P.

The types of XFP transceiver modules may update with

time. For information about them, contact H3C technical

support or marketing staff.

For the models and specifications of each kind of XFP

transceiver modules, see the H3C Low End Series

Ethernet Switches Pluggable Modules Manual on the H3C

website.

Description of LEDs

For information about the description of LEDs, see Table 3 .

LSPM1XP1P

Appearance of the interface card

Figure 3 Front panel of the LSPM1XP1P interface card

Description of LSPM1XP1P

Each LSPM1XP1P interface card provides one 10-Gigabit XFP

fiber port. You can insert an XFP transceiver module into the port to

connect it to another XFP port through an optical fiber. For more

information about the supported XFP transceiver modules and fibers,

see Table 4

Description of LEDs

For information about the description of LEDs, see Table 3 .

Installing and removing an interface card

The following tools are needed for installation and removal of an

interface card:

z Phillips screwdriver

z ESD-preventive wrist strap

Note:

The installation tools are not shipped together with H3C’s

devices. Prepare them yourself.

Installing the interface card

Installing the interface card to the switch

Note:

The procedure of installing the interface card to different

models of H3C switches is similar. This manual takes the

S5500-28C-EI switch as an example.

Follow these steps to install the interface card to the switch:

(1) Wear an ESD-preventive wrist strap, and make sure that the

ESD-pre

ventive wrist strap makes good skin contact and is

properly grounded.

(2) Loosen the mounting screws of the filler panel on the interface

card slo

t of the switch with a Phillips screwdriver and remove the

filler panel, as shown in Figure 4

Figure 4 Install an interface card (I)

(3) Holding the fastening screws on the front panel of the interface

card, g

ently push the interface card in along the slot guide rail

until the interface card is in close contact with the switch, as

shown in Figure 5

(4) Tighten the captive screws with a Phillips screwdriver to fix the

interface

card.

Figure 5 Install an interface card (II)

Caution:

Keep the removed filler panel properly for future use.

When tightening the fastening screws at both sides of the

interface card with a screwdriver or an electric screwdriver,

make sure that the torque is not bigger than 0.4 N-m.

Removing the interface card

Follo

w these steps to remove the interface card:

(1) Wear an ESD-preventive wrist strap, and make sure that the

ESD-pre

ventive wrist strap makes good skin contact and is

properly grounded.

(2) Use a Phillips screwdriver to loosen the captive screws at both

sides of

the interface card until all spring pressure is released.

(3) Pull the interface card towards you along the guide rails, until it

complete

ly comes out of the switch chassis.

Caution:

When installing or removing an interface card, note the

following guidelines:

Do not touch the surface-mounted components directly

with your hands.

Do not use too much force in the operation.

After removing an interface card, if no new interface card

is to be installed, install the filler panel as soon as

possible to prevent dust and ensure normal ventilation in

the switch.

Installing an XFP transceiver module

To avoid component damage caused by improper installation,

carefully read the H3C Pluggable SFP/SFP+/XFP Transceiver

Modules Installation Guide from the H3C's website before installing

the XFP transceiver modules.

Installing and removing the dedicated CX4 cable

Installing the dedicated CX4 cable

Figure 6 CX4 cable

Caution:

Make sure that you have installed the LSPM1CX2P

interface card before installing dedicated CX4 cables.

Follow these steps to install the dedicated CX4 cable:

(1) Wear an ESD-preventive wrist strap and make sure it is properly

grounde

d. Then unpack the dedicated CX4 cable.

(2) Horizontally insert the plug of the dedicated CX4 cable into the

CX4 p

ort of the switch and pay attention to the direction of the

plug when plugging it.

Removing the dedicated CX4 cable

Follow these steps to remove the dedicated CX4 cable:

(1) Wear an ESD-preventive wrist strap and make sure the

ESD-pre

ventive wrist strap properly grounded.

(2) Holding the plug of the CX4 cable, pull the handle at the end of

the plug to h

orizontally unplug the plug of the CX4 cable from the

CX4 port of the switch.

Caution:

Dedicated CX4 cable is hot swappable.

Make sure that the cable bending radius is no less than

eight times of the cable diameter when dedicated CX4

cable is connected.

Verifying the installation

When the switch runs properly, check whether the interface card

is operating properly according to the status of the Port LED on the

interface card.

Technical support

Hangzhou H3C Technologies Co., Ltd. provides customers with

comprehensive technical support and service. If you purchase the

products from the sales agent of Hangzhou H3C Technologies Co.,

Ltd., please contact our sales agent or technical personnel.

Address: 310 Liuhe Road, Zhijiang Science Park,

Hangzhou, Zhejiang Province, P. R. China

Postal Code: 310053

Website: http://www.h3c.com

E-mail: [email protected]

BOM: 3104A02Q

H3C LSPM1XP1P User manual

Brand: H3C

Model: LSPM1XP1P

Type: User manual

This manual is also suitable for

Download PDF

report

H3C LSPM1XP1P User manual

This manual is also suitable for

H3C LSPM1XP1P User manual

Related papers

Other documents