H3C S5500-52C-PWR-EI Quick start guide

Brand: H3C

Model: S5500-52C-PWR-EI

Type: Quick start guide

This manual is also suitable for

H3C S5500-EI & S5500-SI Series Ethernet Switches

Quick Start Guide

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

No part of this manual may be reproduced or transmitted in any form or by any means without prior

written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H

Care,

, TOP G, , IRF, NetPilot, Neocean, NeoVTL,

SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V

G, V

G, PSPT,

XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co.,

Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners.

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Environmental Protection

This product has been designed to comply with the requirements on environmental protection. The

storage, use, and disposal of this product must meet the applicable national laws and regulations.

S5500-EI and S5500-SI Quick Start Guide

About this guide

This guide provides steps for basic installation and configuration for the S5500-EI and S5500-SI

series. Further information, such as optional installation and configuration procedures are

available in the S5500-EI and S5500-SI Installation Guide. For information about changing the

boot mode, loading software, and maintenance and troubleshooting, see the S5500-EI and

S5500-SI Installation Guide.

Product overview

The S5500-EI series include the following models.

• S5500-28C-EI-DC

• S5500-28C-EI

• S5500-52C-EI

• S5500-52C-PWR-EI

• S5500-28C-PWR-EI

• S5500-28F-EI

The S5500-SI series includes the following models.

• S5500-28C-SI

• S5500-52C-SI

• S5500-28C-PWR-SI

• S5500-20TP-SI

Prepare for installation

Safety recommendations

To avoid possible bodily injury and equipment damage, read the following safety

recommendations before installing an H3C S5500-EI or S5500-SI switch; these do not cover

every possible hazardous condition.

• Do not place the switch near water or in a damp environment. Prevent water or moisture

from entering the switch chassis.

• Do not place the switch on an unstable case or desk.

• Ensure proper ventilation of the equipment room and keep the ventilation vents of the switch

free of obstruction.

• Connect the yellow-green protection grounding cable before power-on.

• Make sure that the operating voltage is in the range labeled on the power module of the

switch.

• Do not open the chassis to avoid electrical shocks when the switch is operating or just when

the switch is powered off.

• When replacing interface cards, hot-swappable power modules and fan trays, wear an

ESD-preventive strap to avoid damaging the units.

Examine the installation site

The H3C S5500-EI and S5500-SI series can only be used indoors. Make sure that the floor can

support the weight of the cabinet and the switch chassis.

To ensure the normal operation of the switch, ensure that the following elements meet

requirements described in “Preparing for installation” in the S5500-EI and S5500-SI Installation

Guide: room temperature, humidity, cleanness, EMS and laser safety.

Installation tools

The installation tools are not shipped with the S5500-EI and S5500-SI series.

• Flat-blade screwdriver

• Phillips screwdriver

• ESD-preventive wrist strap

Install the switch

This guide provides basic installation steps. See the S5500-EI and S5500-SI Installation Guide for

comprehensive product information, including port, LEDs and optional interface module

specifications as well as steps for installing the switch on a workbench, loading software and

maintenance and troubleshooting.

To avoid bodily injury, do not touch any wire, terminal, or part marked with a high-voltage hazard sign.

Installation workflow

Figure 1 Installation flow of the switch

Install the switch on a rack

This section provides steps to install the switch on a 19-inch rack using mounting brackets and a

tray. The S5500-EI and S5500-SI Installation Guide provides comprehensive steps for mounting

brackets, guide rails, as well as instructions for front and rear mounting brackets and installing

the switch on a workbench.

All models of the S5500-EI and S5500-SI series support installation using front mounting brackets

together with a tray.

Follow these steps to install a switch into a 19-inch standard cabinet:

1. Wear an ESD-preventive wrist strap and ensure a good skin contact and grounding.

Check the grounding and stability of the cabinet.

3. Fix the delivered tray horizontally in a proper position.

4. Take out the screws which are packed together with the front mounting brackets, and fix one

end of mounting brackets to the switch.

5. Place the switch on the tray horizontally, slide the tray into the cabinet, and fix the other end

of mounting brackets to the front brackets with crews and captive nuts.

Connect the ground wire

This section documents when a grounding strip is available. For information for when there is no

grounding strip or for other installation sites, see the S5500-EI and S5500-SI Installation Guide.

Correctly connecting the switch ground wire is crucial to the lightning protection and EMS of a

switch. When a grounding strip is available at the installation site, attach one end of the yellow-

green ground wire of the switch to the grounding screw on the grounding strip (the grounding

screw and the grounding hole are on the rear panel of the switch and are marked with a

grounding sign). To do this, follow these steps:

1. Remove the grounding screw from the rear panel of the switch chassis.

2. Put the supplied OT terminal of the PGND cable on the grounding screw.

3. Fasten the grounding screw, which is attached with the OT terminal of the PGND cable, into

the grounding screw hole with a screwdriver.

Install the power module

The following section describes how to install a power module for only the S5500-28F-EI and

S5500-20TP-SI Ethernet switches.

The installation/removal procedure of the PSR150-A and PSR150-D is similar. This manual takes

the PSR150-A as an example to introduce the installation and removal of the power module.

Follow these steps:

1. Wear an ESD-preventive wrist strap, ensure a good skin contact and make sure that the ESD-

preventive wrist strap is properly grounded.

2. Take the power module from the package and check that the power module model is as

required.

3. Face the slot into which the power module is to be inserted.

4. Insert the power module with the upside up. (if you insert it with the upside down, the

insertion is not smooth because of the specific structure design of the power module and

slot). Grasp the handle of the module with one hand and hold the module bottom with the

other, and then slide the module slowly along the guide rails into the slot.

5. Fasten the captive screw on the power module clockwise with a Philips screwdriver until the

power module is fixed into the chassis.

Connect the power cord

After you insert the power module into the device, you can connect the power cord. This manual

includes steps to connect the AC power cord. See the S5500-EI and S5500-SI Installation Guide

for power cord connection methods and steps to connect the -48V DC and RPS power cords. To

connect an AC power cord, follow these steps:

1. Wear an ESD-preventive wrist strap, ensure a good skin contact and make sure that the ESD-

preventive wrist strap is properly grounded.

2. Install the bail latch to prevent the AC power cord from accidentally falling off. Fix the bail

latch into the holes located at the two sides of the AC power receptacle. Then pull the bail

latch upwards.

3. Connect one end of the AC power cord to the AC receptacle on the switch.

4. Pull the bail latch down to secure the plug to the AC receptacle.

5. Connect the other end of the AC power cord to the external AC power supply system.

6. Check whether the system status LED (PWR/SYS) on the front panel of the switch is ON. If

the LED is ON, it shows the power cord is properly connected.

Install an interface module

Each S5500-EI and S5500-SI switch (except S5500-20TP-SI) provide two interface module slots

on the rear panel.

The installation and removal of various interface modules are similar. This section describes the

installation and removal of the Dual-Port 10 GE SFP+ Interface Module (LSPM2SP2P) for

illustration. For information on installing a dedicated CX4/SFP+ cable, see the S5500-EI and

S5500-SI Installation Guide.

1. Wear an ESD-preventive wrist strap, ensure a good skin contact and make sure that the ESD-

preventive wrist strap is properly grounded.

2. Loosen the mounting screws of the filler panel on the interface card slot of the switch's front

panel with a Phillips screwdriver and remove the filler panel.

3. Unwrap the interface card. Gently push the interface card in along the slot guide rails until

the interface card is in close contact with the switch. Then push the ejector levers at both

sides inward.

4. Tighten the captive screws with a Phillips screwdriver to fix the interface card.

S5500-EI only: installing switches for an IRF

The S5500-EI series support the IRF function. You can install IRF-capable interface modules to

connect multiple switches through the 10 GE ports to form a logical entity. See the S5500-EI and

S5500-SI Installation Guide for more information.

Verify the installation

Before powering on the S5500-EI and S5500-SI series switch, check the following items are in

place:

• There is enough space for heat dissipation around the switch, and the rack or workbench is

stable.

• The ground wire is connected.

• The selected power module matches that required by the switch and the power cables are

properly connected.

• All the interface cables are cabled indoors. If there is any cable wired outdoors, verify that

socket strip with lightning protection and lightning arresters for network ports have been

properly connected.

Connect the switch to the network

Connect the console cable

When you want to use the terminal to configure the switch, follow these steps to connect a

terminal device to the switch using the console cable:

1. Plug the DB-9 female connector of the console cable to the serial port of the console terminal

or PC.

2. Connect the RJ-45 connector of the console cable to the console port of the switch.

Set up a configuration environment

1. Launch a terminal emulation utility. Select Start > Programs > Accessories >

Communications > HyperTerminal to access the HyperTerminal window. Click

the window to set up a new connection.

2. Enter the name of the new connection in the Connection Description dialog box, and

click OK. Select a port from the Connect using drop-down list.

3. Set serial port parameters. Set the bits per second to 9600, data bits to 8, parity to None,

stop bits to 1, and flow control to None.

4. Click OK to enter the HypterTerminal window,

5. Select File > Properties in the HyperTerminal window. Click Settings in the Window,

select VT100 for terminal emulation, and click OK.

Power on the switch

Before powering on the switch, verify that:

• The power cable is properly connected.

• The power supply voltage meets the requirement of the switch.

• The console cable is properly connected; the terminal or PC used for configuration has been

started; and the configuration parameters have been set.

H3C S5500-52C-PWR-EI Quick start guide

Brand: H3C

Model: S5500-52C-PWR-EI

Type: Quick start guide

This manual is also suitable for

Download PDF

report

H3C S5500-52C-PWR-EI Quick start guide

This manual is also suitable for

H3C S5500-52C-PWR-EI Quick start guide

Related papers

Other documents