H3C S5500-52 C-EI Installation guide

Brand: H3C

Model: S5500-52 C-EI

Category: Network switches

Type: Installation guide

This manual is also suitable for

H3C S5500-EI Series Ethernet Switches

Installation Manual

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Manual Version: 20090726-C-1.02

No part of this manual may be reproduced or transmitted in any form or by any means without prior

written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H

Care,

, TOP G, , IRF, NetPilot, Neocean, NeoVTL,

SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V

G, V

G, PSPT,

XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co.,

Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners.

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Technical Support

customer_service@h3c.com

http://www.h3c.com

About This Manual

Organization

H3C S5500-EI Series Ethernet Switches Installation Manual is organized as follows:

Chapter Contents

1 Product Overview

Briefly introduces the appearance, system description, as well as

the features and applications of the S5500-EI series switches.

2 Preparing for Installation

Describes the requirements on installation site, the safety

recommendations before and during installation, and the

required tools.

3 Installing the Switch

Covers the procedures for installing the S5500-EI series

switches, ground wire connection, power module installation,

interface module installation, and so on.

4 Starting and Configuring the

Switch

Helps you get familiar with the basic knowledge of how to boot

and configure the S5500-EI series switches, including device

startup, power-on, and initialization of system files, and so on.

5 Boot ROM and Host Software

Introduces how to load Boot ROM and host software for an

S5500-EI series switch

6 Maintenance and

Troubleshooting

Introduces the problems that might occur during the installation

and the booting of an S5500-EI series switch and the related

solution.

Appendix A Lightning Protection

of the Switch

Introduces lightning protection of S5500-EI Series Ethernet

Switches.

Conventions

The manual uses the following conventions:

Command conventions

Convention Description

Boldface

The keywords of a command line are in Boldface.

italic

Command arguments are in italic.

[ ] Items (keywords or arguments) in square brackets [ ] are optional.

{ x | y | ... }

Alternative items are grouped in braces and separated by vertical bars.

One is selected.

[ x | y | ... ]

Optional alternative items are grouped in square brackets and

separated by vertical bars. One or none is selected.

{ x | y | ... } *

Alternative items are grouped in braces and separated by vertical bars.

A minimum of one or a maximum of all can be selected.

[ x | y | ... ] *

Optional alternative items are grouped in square brackets and

separated by vertical bars. Many or none can be selected.

&<1-n>

The argument(s) before the ampersand (&) sign can be entered 1 to n

times.

# A line starting with the # sign is comments.

GUI conventions

Convention Description

Boldface

Window names, button names, field names, and menu items are in

Boldface. For example, the New User window appears; click OK.

Multi-level menus are separated by angle brackets. For example, File >

Create > Folder.

Symbols

Convention Description

Means reader be extremely careful. Improper operation may cause

bodily injury.

Means reader be careful. Improper operation may cause data loss or

damage to equipment.

Means a complementary description.

Related Documentation

In addition to this manual, each H3C S5500-EI Series Ethernet Switches documentation set includes

the following:

Manual Description

H3C S5500-EI Series Ethernet

Switches Operation Manual

It is used for assisting the users in data configurations and typical

applications. It includes Product Overview, Access Volume, IP

Service Volume, IP Routing Volume, IP Multicast Volume, QoS

Volume, Security Volume and System Volume.

H3C S5500-EI Series Ethernet

Switches Command Manual

It is used for assisting the users in using various commands. It

includes Command Index, Access Volume, IP Services Volume,

IP Routing Volume, IP Multicast Volume, QoS Volume, Security

Volume and System Volume.

Obtaining Documentation

You can access the most up-to-date H3C product documentation on the World Wide Web at this URL:

http://www.h3c.com.

The following are the columns from which you can obtain different categories of product documentation:

[Products & Solutions]: Provides information about products and technologies, as well as solutions.

[Technical Support & Document > Technical Documents]: Provides several categories of product

documentation, such as installation, configuration, and maintenance.

[Technical Support & Document > Software Download]: Provides the documentation released with the

software version.

Documentation Feedback

You can e-mail your comments about product documentation to [email protected].

We appreciate your comments.

Environmental Protection

This product has been designed to comply with the requirements on environmental protection. For the

proper storage, use and disposal of this product, national laws and regulations must be observed.

Table of Contents

1 Product Overview······································································································································1-1

Overview ·················································································································································1-1

Introduction to S5500-EI Series Ethernet Switches················································································1-3

S5500-28C-EI··································································································································1-3

S5500-28C-EI-DC ···························································································································1-5

S5500-52C-EI··································································································································1-5

S5500-28C-PWR-EI ························································································································1-6

S5500-52C-PWR-EI ························································································································1-7

S5500-28F-EI ··································································································································1-8

Ports······················································································································································1-10

Console Port··································································································································1-10

10/100/1000Base-T Ethernet Port·································································································1-10

SFP Port ········································································································································1-10

Combo Port ···································································································································1-12

LEDs······················································································································································1-13

System Status LED ·······················································································································1-13

Hot Swappable Power Module Status LEDs·················································································1-13

RPS Status LED ····························································································································1-14

Port Mode LED ······························································································································1-14

Seven-Segment LED·····················································································································1-15

10/100/1000Base-T Auto-Sensing Ethernet Port Status LED·······················································1-16

SFP Port Status LED·····················································································································1-17

Interface Module Status LED ········································································································1-17

Optional Interface Modules ···················································································································1-17

Dual-port GE SFP interface module······························································································1-18

Short-haul Dual-Port 10 GE CX4 Interface Module ······································································1-19

Dual-Port 10 GE SFP+ Interface Module ······················································································1-20

Dual-Port 10 GE XFP Interface Module ························································································1-22

One-port 10 GE XFP Interface Module ·························································································1-23

Description of LEDs of Interface Modules ·····················································································1-23

2 Preparing for Installation··························································································································2-1

Safety Precautions ··································································································································2-1

Installation Site········································································································································2-1

Temperature/Humidity·····················································································································2-1

Cleanness········································································································································2-1

Electromagnetic Susceptibility·········································································································2-2

Laser Safety ····································································································································2-2

Installation Tools ·····································································································································2-3

3 Installing the Switch··································································································································3-1

Installation Flow of the Switch·················································································································3-1

Installing the Switch into a 19-Inch Rack Using Mounting Brackets·······················································3-2

Installation Modes····························································································································3-2

Introduction to Mounting Bracket·····································································································3-3

Introduction to Guide Rail················································································································3-4

Use Front Mounting Brackets to Install a Switch·············································································3-4

Use Front Mounting Brackets and a Tray to Install a Switch ··························································3-5

Use Front and Rear Mounting Brackets to Install a Switch·····························································3-6

Use Front Mounting Brackets and Guide Rails to Install a Switch··················································3-9

Mounting the Switch on a Workbench ··································································································3-11

Connecting the Grounding Cable··········································································································3-11

When a Grounding Strip is Available·····························································································3-12

Where a Grounding Conductor Can be Buried ·············································································3-13

In Other Installation Sites ··············································································································3-14

Installing a Power Module·····················································································································3-15

Installing the Power Module ··········································································································3-15

Removing the Power Module ········································································································3-16

Connecting the Power Cords ················································································································3-17

Connecting the AC Power Cord ····································································································3-17

Connecting the -48V DC Power Cord ···························································································3-18

Connecting the RPS Power Cord··································································································3-19

Installing an Interface Module ···············································································································3-21

Installing an Interface Card ···········································································································3-21

Removing an Interface Module ·····································································································3-22

Installing Dedicated CX4/SFP+ Cable ··························································································3-23

Removing Dedicated CX4/SFP+ Cable ························································································3-23

Installing Switches for an IRF ···············································································································3-23

Installation Flow for an IRF············································································································3-24

Drawing a Plan for an IRF with Switches ······················································································3-25

Verifying the Installation························································································································3-28

4 Starting and Configuring the Switch·······································································································4-1

Setting up the Configuration Environment ······························································································4-1

Connecting the Console Cable ···············································································································4-1

Console Cable ·································································································································4-1

Connection Procedure·····················································································································4-2

Setting Terminal Parameters ··················································································································4-2

Booting the Switch ··································································································································4-5

Checking before Powering on the Switch························································································4-5

Powering on the Switch···················································································································4-5

Changing the Startup Mode ············································································································4-8

5 Boot ROM and Host Software Loading ···································································································5-1

Introduction to Loading Modes················································································································5-1

Loading Software Through the Boot ROM Menu····················································································5-1

Boot Menu ·······································································································································5-1

Loading Software Using XMODEM Through Console Port·····························································5-3

Loading Software Using TFTP through Ethernet Port·····································································5-8

Loading Software Using FTP Through Ethernet Port····································································5-10

Loading Software Through CLI ·············································································································5-12

Loading Software Using FTP ········································································································5-12

Loading Software Using TFTP ······································································································5-14

iii

6 Maintenance and Troubleshooting··········································································································6-1

Software Loading Failure ························································································································6-1

Password Missing Failure ·······················································································································6-1

Missing User Password ···················································································································6-1

Missing Boot ROM Password··········································································································6-1

Power Supply Failure······························································································································6-2

Fixed Power Module Failure············································································································6-2

Hot Swappable Power Module Failure ····························································································6-3

Fan Failure ··············································································································································6-4

Configuration System Failure··················································································································6-4

1-1

1 Product Overview

Overview

H3C S5500-EI Series Ethernet Switches (hereinafter referred to as the S5500-EI series) are Layer 3

Gigabit Ethernet switching products developed by Hangzhou H3C Technologies Co., Ltd. (hereinafter

referred to as H3C).

The S5500-EI series are designed as distribution or access devices for intranets and metropolitan area

networks (MANs). Supporting IPv4/IPv6 dual stack and 10 GE uplink interfaces, the S5500-EI series

provide abundant service features and can also be used for connecting server groups in data centers.

The S5500-EI series support the H3C-specific cluster management function, which facilitates your

network management. And they also support the Intelligent Resilient Framework (IRF) technology. You

can connect multiple S5500-EI switches through 10 GE ports to form a logical entity, thus to establish a

new intelligent network with high reliability, expandability and manageability.

The S5500-EI series include six models, and have the system specifications as shown in

Table 1-1.

Table 1-1 System specifications of the S5500-EI series

Item

S5500-28

C-EI-DC

S5500-

28C-EI

S5500-52

C-EI

S5500-52C-

PWR-EI

S5500-28C-P

WR-EI

S5500-28F-EI

Physical

dimensions

(H × W × D)

43.6 × 440 × 300 mm

(1.72 × 17.32 × 11.81 in.)

43.6 × 440 × 420 mm

(1.72 × 17.32 × 16.54 in.)

43.6 × 440 ×

360 mm

(1.72 × 17.32 ×

14.17 in.)

Weight <5 kg (11.02 lb) <7.5 kg (16.53 lb) <6 kg (13.23 lb)

Management

port

One console port, on the front panel

24 ×

10/100/1000Base-T

auto-sensing

Ethernet port

4 × 1000Base-X

SFP port

48 ×10/100/1000Base-T

auto-sensing Ethernet

port

4 × 1000Base-X SFP port

24 ×

10/100/1000B

ase-T

auto-sensing

Ethernet port

4 ×

1000Base-X

SFP port

8 ×

10/100/1000Ba

se-T Ethernet

port

24 ×

100/1000Base-

X SFP port

The last four 10/100/1000Base-T Ethernet ports and the four SFP

ports comprise four Combo ports.

The last eight

SFP ports and

the eight

10/100/1000Ba

se-T Ethernet

ports comprise

eight Combo

ports.

GE ports

Note: For each Combo port, either the SFP port or the corresponding Ethernet port

can be used at a time. For details about the combo port mapping relationship, please

refer to

Table 1-5.

1-2

Item

S5500-28

C-EI-DC

S5500-

28C-EI

S5500-52

C-EI

S5500-52C-

PWR-EI

S5500-28C-P

WR-EI

S5500-28F-EI

Interface

card models

supported

(optional)

2, on the rear panel

z Dual-port GE SFP interface module (LSPM2GP2P, not support IRF)

z Short-haul dual-port 10GE CX4 interface module (LSPM1CX2P, support IRF)

z Dual-port 10 GE SFP+ interface module (LSPM2SP2P, support IRF)

z Dual-port 10 GE XFP interface module (LSPM1XP2P, support IRF)

z One-port 10 GE XFP interface module (LSPM1XP1P, support IRF)

Optional hot

swappable

power

modules

—

PSR150-A

PSR150-D

Power

supply

system

The S5500-28F-EI is delivered with a hot-swappable power module PSR150-A by

default. You can install another PSR150-A or a PSR150-D for backup.

The other five models of the S5500-EI series switches are designed with two fixed

power receptacles respectively. The two power inputs can be simultaneously used,

acting as backup for each other. Alternatively, you can use either power input.

Power

socket types

and quantity

1 -48V DC

power

socket and

1 RPS

power

socket

1 AC power socket

and 1 RPS power

socket

1 AC power socket and 1 RPS

power socket

PSR150-A: 1

AC power

socket

PSR150-D: 1

-48V DC power

socket

Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz

Input voltage range: 90 VAC to 264 VA.C, 47 Hz to 63 Hz

–48V

Rated voltage range: –48 VDC to –60 VDC

Input voltage range: –36 VDC to –72 VDC

You can use the –48 VDC power supply in the equipment room directly or one of the

following two external RPS power supply units recommended by H3C to provide

power supply.

z RPS500-A3 (–50 VDC/7.5 A, cable suite-0404A03V) or RPS1000-A3 (–54

VDC/8 A, cable suite-0404A054) for the PSR150-D power module installed on an

S5500-28F-EI.

z RPS500-A3 (–50 VDC/7.5 A, cable suite-0404A03U) for the S5500-28C-EI-DC.

Input

volta

RPS

Use the external RPS power supply units recommended by H3C only.

z S5500-28C-EI/S5500-28C-EI-DC has a rated voltage range of 10.8 VDC to 13.2

VDC, and adopts RPS500-A3 using its 12 VDC/10.5 A output and the cable suite

of 0404A08G.

z S5500-52C-EI has a rated voltage range of 10.8 VDC to 13.2 VDC, and adopts

RPS800-A using its 12 VDC/17.25 A output and the cable suite of 0404A08G.

z S5500-28C-PWR-EI/S5500-52C-PWR-EI has a rated voltage range of –55 VDC

to –52 VDC, and adopts RPS1000-A3 using its –54 VDC/25 A output and the

cable suite of 0404A053.

Static power

consumption

27 W 36 W 63 W 83 W 60 W

PSR150-A: 44

PSR150-D: 30

1-3

Item

S5500-28

C-EI-DC

S5500-

28C-EI

S5500-52

C-EI

S5500-52C-

PWR-EI

S5500-28C-P

WR-EI

S5500-28F-EI

AC power

supply:

640 W, with

270 W of

system

power

consumption

and 370 W of

PoE power

AC power

supply:

575 W, with

205 W of

system power

consumption

and 370 W of

PoE power

Power

consumption

(full load)

105 W 110 W 155 W

RPS power

supply:

910 W, with

170 W of

system

power

consumption

and 740 W of

PoE power

RPS power

supply:

485 W, with

115 W of

system power

consumption

and 370 W of

PoE power

115 W

Cooling

system

4 fans 6 fans

6 fans (4 for the

system, and 1

for each power

module)

Operating

temperature

0°C to 45°C (32°F to 113°F)

Relative

humidity

(noncondens

ing)

10% to 90%

z Only the recommended RPS can be used for S5500-EI Ethernet switches. The –48 VDC in the

equipment room cannot be used directly. Otherwise, the device may be damaged.

z For details about the RPS power supply units, see the user manual and RPS Ordering Guide for

H3C Low-End Series Ethernet Switches.

Introduction to S5500-EI Series Ethernet Switches

S5500-28C-EI

Front Panel

The S5500-28C-EI Ethernet switch provides 24 × 10/100/1000Base-T auto-sensing Ethernet ports, four

1000 Base-X SFP ports and one console port on the front panel. The last four 10/100/1000Base-T

Ethernet ports and the four SFP ports comprise four Combo ports, with one port of a Combo port

working at a time.

1-4

Figure 1-1 Front panel of the S5500-28C-EI Ethernet switch

(1) 10/100/1000 Base-T auto-sensing Ethernet port

(2) 10/100/1000 Base-T auto-sensing Ethernet port status LED

(3) 1000 Base-X SFP port (4) 1000Base-X SFP port status LED

(5) Console port (6) Seven-segment LED

(7) Port mode LED (Mode) (8) System status LED (PWR)

(9) RPS status LED (RPS) (10) Interface module 1 status LED (MOD1)

(11) Interface module 2 status LED (MOD2) (12) Port status LED mode switching button

Rear Panel

Figure 1-2 Rear panel of the S5500-28C-EI Ethernet switch

(1) AC power input (2) RPS power input (shipped with a protective cover)

(3) Grounding screw (4) Interface module slot 1 (MOD1)

(5) Interface module slot 2 (MOD2)

The S5500-28C-EI provides two interface module slots on its rear panel. Each slot is installed with a

filler panel when the switch is shipped. You can select one or two interface modules for your switch as

needed. See

Optional Interface Modules on page 1-17 for the interface module models supported by

the S5500-EI series, and see

Installing an Interface Module on page 3-21 for the installation of interface

modules.

1-5

S5500-28C-EI-DC

Front Panel

The front panel of the S5500-28C-EI-DC is the same as that of the S5500-28C-EI. For related

description, refer to

S5500-28C-EI on page 1-3.

Rear Panel

Figure 1-3 Rear panel of the S5500-28C-EI-DC Ethernet switch

(1) -48V DC power input (2) RPS power input (shipped with a protective cover)

(3) Grounding screw (4) Interface module slot 1 (MOD1)

(5) Interface module slot 2 (MOD2)

The S5500-28C-EI-DC provides two interface module slots on its rear panel. Each slot is installed with

a filler panel when the switch is shipped. You can select one or two interface modules for your switch as

needed. See

Optional Interface Modules on page 1-17 for the interface module models supported by

the S5500-EI series, and see

Installing an Interface Module on page 3-21 for the installation of interface

modules.

S5500-52C-EI

Front Panel

The S5500-52C-EI Ethernet switch provides 48 ×10/100/1000Base-T auto-sensing Ethernet ports, four

1000 Base-X SFP ports and one console port on the front panel. The last four 10/100/1000Base-T

Ethernet ports and the four SFP ports comprise four Combo ports, with one port of a Combo port

working at a time.

1-6

Figure 1-4 Front panel of the S5500-52C-EI Ethernet switch

(1) 10/100/1000 Base-T auto-sensing Ethernet port

(2) 10/100/1000 Base-T auto-sensing Ethernet port status LED

(3) Console port (4) Seven-segment LED

(5) Port mode LED (Mode) (6) System status LED (PWR)

(7) RPS status LED (RPS) (8) Interface module 1 status LED (MOD1)

(9) Interface module 2 status LED (MOD2) (10) Port status LED mode switching button

(11) 1000 Base-X SFP port (12) 1000Base-X SFP port status LED

Rear Panel

Figure 1-5 Rear panel of the S5500-52C-EI Ethernet switch

(1) AC power input (2) RPS power input (shipped with a protective cover)

(3) Grounding screw (4) Interface module slot 1 (MOD1)

(5) Interface module slot 2 (MOD2)

The S5500-52C-EI provides two interface module slots on its rear panel. Each slot is installed with a

filler panel when the switch is shipped. You can select one or two interface modules for your switch as

needed. See

Optional Interface Modules on page 1-17 for the interface module models supported by

the S5500-EI series, and see

Installing an Interface Module on page 3-21 for the installation of interface

modules.

S5500-28C-PWR-EI

Front Panel

The S5500-28C-PWR-EI Ethernet switch provides 24 ×10/100/1000Base-T auto-sensing Ethernet

ports, four 1000 Base-X SFP ports and one console port on the front panel. The last four

10/100/1000Base-T Ethernet ports and the four SFP ports comprise four Combo ports, with one port of

a Combo port working at a time.

1-7

Figure 1-6 Front panel of the S5500-28C-PWR-EI Ethernet switch

(1) 10/100/1000 Base-T auto-sensing Ethernet port

(2) 10/100/1000 Base-T auto-sensing Ethernet port status LED

(3) 1000 Base-X SFP port (4) 1000Base-X SFP port status LED

(5) Console port (6) Seven-segment LED

(7) Port mode LED (Mode) (8) System status LED (PWR)

(9) RPS status LED (RPS) (10) Interface module 1 status LED (MOD1)

(11) Interface module 2 status LED (MOD2) (12) Port status LED mode switching button

Rear Panel

Figure 1-7 Rear panel of the S5500-28C-PWR-EI Ethernet switch

(1) RPS power input (2) AC power input

(3) Grounding screw (4) Interface module slot 1 (MOD1)

(5) Interface module slot 2 (MOD2)

The S5500-28C-PWR-EI provides two interface module slots on its rear panel. Each slot is installed

with a filler panel when the switch is shipped. You can select one or two interface modules for your

switch as needed. See

Optional Interface Modules on page 1-17 for the interface module models

supported by the S5500-EI series, and see

Installing an Interface Module on page 3-21 for the

installation of interface modules.

S5500-52C-PWR-EI

Front Panel

The S5500-52C-PWR-EI Ethernet switch provides 48 ×10/100/1000Base-T auto-sensing Ethernet

ports, four 1000 Base-X SFP ports and one console port on the front panel. The last four

10/100/1000Base-T Ethernet ports and the four SFP ports comprise four Combo ports, with one port of

a Combo port working at a time.

1-8

Figure 1-8 Front panel of the S5500-52C-PWR-EI Ethernet switch

(1) 10/100/1000 Base-T auto-sensing Ethernet port

(2) 10/100/1000 Base-T auto-sensing Ethernet port status LED

(3) Console port (4) Seven-segment LED

(5) Port mode LED (Mode) (6) System status LED (PWR)

(7) RPS status LED (RPS) (8) Interface module 1 status LED (MOD1)

(9) Interface module 2 status LED (MOD2) (10) Port status LED mode switching button

(11) 1000 Base-X SFP port (12) 1000Base-X SFP port status LED

Rear Panel

Figure 1-9 Rear panel of the S5500-52C-PWR-EI Ethernet switch

(1) RPS power input (2) AC power input

(3) Grounding screw (4) Interface module slot 1 (MOD1)

(5) Interface module slot 2 (MOD2)

The S5500-52C-PWR-EI provides two interface module slots on its rear panel. Each slot is installed

with a filler panel when the switch is shipped. You can select one or two interface modules for your

switch as needed. See

Optional Interface Modules on page 1-17 for the interface module models

supported by the S5500-EI series, and see

Installing an Interface Module on page 3-21 for the

installation of interface modules.

S5500-28F-EI

Front Panel

The S5500-28F-EI Ethernet switch provides 24 × 100/1000Base-X SFP ports, eight

10/100/1000Base-T auto-sensing Ethernet ports and one console port on the front panel. The last eight

SFP ports and the eight 10/100/1000Base-T Ethernet ports comprise eight Combo ports, with one port

of a Combo port working at a time.

1-9

Figure 1-10 Front panel of the S5500-28F-EI Ethernet switch

(1) 100/1000Base-X SFP port status LED (2) 10/100/1000 Base-T auto-sensing Ethernet port

status LED

(3) Console port (4) Port status LED mode switching button

(5) Interface module 1 status LED (MOD1) (6) Interface module 2 status LED (MOD2)

(7) System status LED (SYS) (8) Hot swappable power module 1 status LED

(PWR1)

(9) Hot swappable power module 2 status LED

(PWR2)

(10) Port mode LED (Mode)

(11) Seven-segment LED

Rear Panel

Figure 1-11 Rear panel of the S5500-28F-EI Ethernet switch

(1) Grounding screw (2) Hot swappable power module 1

(3) Hot swappable power module 2 (4) Interface module slot 1 (MOD1)

(5) Interface module slot 2 (MOD2)

z The S5500-28F-EI provides two interface module slots on its rear panel. Each slot is installed with

a filler panel when the switch is shipped. You can select one or two interface modules for your

switch as needed. See

Optional Interface Modules on page 1-17 for the interface module models

supported by the S5500-EI series, and see

Installing an Interface Module on page 3-21 for the

installation of interface modules.

z The S5500-28F-EI provides two power module slots on its rear panel, with only a power module

RPS150-A installed in PWR1 upon device delivery while a blank panel on PWR2. You can install a

power module, which can be PSR150-A or PSR150-D, in PWR2 to serve as a backup. For details

about PSR150-A and PSR150-D, refer to H3C PSR150-A & PSR150-D Power Modules User

Manual. For details about how to install the two power modules, refer to

Installing a Power Module.

1-10

Ports

Console Port

Each S5500-EI series provides one console port on the front panel. Table 1-2 describes the console

port specifications.

Table 1-2 Console port specifications

Item Specification

Connector type

RJ-45

Compliant standard

EIA/TIA-232

Transmission baud

rate

9600 bps to 115200 bps (defaulting to 9600 bps)

Service

z It can be connected to an ASCII terminal.

z It can be connected to a serial port of a local or remote (through a pair of

modems) PC running terminal emulation program.

10/100/1000Base-T Ethernet Port

Each S5500-EI series provides 10/100/1000Base-T Ethernet ports on its front panel. Table 1-3

describes the specifications of the 10/100/1000Base-T Ethernet ports.

Table 1-3 10/100/1000Base-T Ethernet port specifications

Item Specification

Connector type

RJ-45

Interface standard

z 10 Mbps, full duplex

z 100 Mbps, full duplex

z 1000 Mbps, full duplex

z MDI/MDI-X, auto-sensing

Max transmission

distance

100 m (328.08 ft.)

Transmission medium

Category-5 unshielded twisted pair cable

Standard

IEEE 802.3i, 802.3u, 802.3ab

SFP Port

Each S5500-EI series provides SFP ports on its front panel. You can select the SFP transceivers

described in

Table 1-4.

All SFP transceivers are hot swappable and optional. Therefore, networking is more flexible.

1-11

Table 1-4 SFP transceivers supported by the S5500-EI series SFP ports

Transceiver

Central

wavelength

Connect

Fiber

Max

transmiss

ion

distance

50/125 µm

multimode

optical fiber

550 m

(1804.5 ft)

SFP-GE-SX-MM850-A 850 nm

62.5/125 µm

multimode

optical fiber

275 m

(902.2 ft)

SFP-GE-LX-SM1310-A

10 km

(about 6.2

mi)

SFP-GE-LH40-SM1310

1310 nm

40 km

(about

24.9 mi)

SFP-GE-LH40-SM1550

40 km

(about

24.9 mi)

SFP-GE-LH70-SM1550

1550 nm

9/125 µm

single mode

optical fiber

70 km

(about

43.5 mi)

SFP-GE-LX-

SM1310-BIDI

TX: 1310 nm

RX: 1490 nm

GE SFP

transcei

ver

SFP-GE-LX-

SM1490-BIDI

Note that

these two

transceiver

models

should be

used in

pairs.

TX: 1490 nm

RX: 1310 nm

9/125 µm

single mode

optical fiber

10 km

(about 6.2

mi)

SFP-FE-SX-MM1310-A

62.5/125 µm

multimode

optical fiber

2 km

(about 1.2

mi)

SFP-FE-LX-SM1310-A

9/125 µm

single mode

optical fiber

15 km

(about 9.3

mi)

SFP-FE-LH40-SM1310

1310 nm

9/125 µm

single mode

optical fiber

40 km

(about

24.9 mi)

SFP-FE-LH80-SM1550 1550 nm

9/125 µm

single mode

optical fiber

80 km

(about

49.7 mi)

SFP-FE-LX-S

M1310-BIDI

TX: 1310 nm

RX: 1550 nm

FE SFP

transcei

ver

SFP-FE-LX-S

M1550-BIDI

Note that

these two

transceiver

models

should be

used in

pairs.

TX: 1550 nm

RX: 1310 nm

9/125 µm

single mode

optical fiber

15 km

(about 9.3

mi)

1-12

z You are recommended to use SFP transceivers of H3C on the S5500-EI series.

z The types of SFP transceivers may update with time. For information about transceivers, contact

H3C technical support or marketing staff.

z For the models and specifications of each kind of transceivers, refer to H3C Low End Series

Ethernet Switches Pluggable Modules Manual.

Combo Port

One SFP port and the corresponding 10/100/1000Base-T Ethernet port form a Combo port. For each

Combo port, either the SFP port or the corresponding 10/100/1000Base-T Ethernet port can be used at

a time. For details about the combo port mapping relationship, please refer to

Table 1-5.

Table 1-5 Combo port mapping relationship

Model SFP port 10/100/1000Base-T Ethernet port

GigabitEthernet1/0/25 GigabitEthernet1/0/22

GigabitEthernet1/0/26 GigabitEthernet1/0/24

GigabitEthernet1/0/27 GigabitEthernet1/0/21

S5500-28C-EI

S5500-28C-EI-DC

S5500-28C-PWR-EI

GigabitEthernet1/0/28 GigabitEthernet1/0/23

GigabitEthernet1/0/49 GigabitEthernet1/0/46

GigabitEthernet1/0/50 GigabitEthernet1/0/48

GigabitEthernet1/0/51 GigabitEthernet1/0/45

S5500-52C-EI

S5500-52C-PWR-EI

GigabitEthernet1/0/52 GigabitEthernet1/0/47

GigabitEthernet1/0/25 GigabitEthernet1/0/17

GigabitEthernet1/0/26 GigabitEthernet1/0/18

GigabitEthernet1/0/27 GigabitEthernet1/0/19

GigabitEthernet1/0/28 GigabitEthernet1/0/20

GigabitEthernet1/0/29 GigabitEthernet1/0/21

GigabitEthernet1/0/30 GigabitEthernet1/0/22

GigabitEthernet1/0/31 GigabitEthernet1/0/23

S5500-28F-EI

GigabitEthernet1/0/32 GigabitEthernet1/0/24

The SFP port and its corresponding 10/100/1000Base-T autosensing Ethernet port cannot be used

together at the same time. For details, refer to the Ethernet Port Configuration part in the Access

Volume of the H3C S5500-EI Series Ethernet Switches Operation Manual.

Page is loading ...

H3C S5500-52 C-EI Installation guide

Brand: H3C

Model: S5500-52 C-EI

Category: Network switches

Type: Installation guide

This manual is also suitable for

Download PDF

report

H3C S5500-52 C-EI Installation guide

This manual is also suitable for

H3C S5500-52 C-EI Installation guide

Related papers

Other documents