Maxxima MSL-17150RB Installation guide

Type
Installation guide

This manual is also suitable for

Maxxima MSL-17150RB is a 17” LED Picture Light designed for indoor use. It provides bright, even illumination for artwork, photographs, and other display items. The fixture is easy to install and can be mounted on a wall or ceiling. It has a durable construction and a 3-year warranty.

Maxxima MSL-17150RB is a 17” LED Picture Light designed for indoor use. It provides bright, even illumination for artwork, photographs, and other display items. The fixture is easy to install and can be mounted on a wall or ceiling. It has a durable construction and a 3-year warranty.

17” LED Picture Light Installation Guide MSL-17150
www.maxximastyle.com
FIXTURE MOUNTING AND WIRING INSTRUCTIONS
info@maxximastyle.com 866-MAXXIMA (629-9462) www.maxximastyle.com 125 Cabot Court Hauppauge, NY 11788
3 YEAR WARRANTY
Maxxima extends a 3 year limited warranty to the original purchase that the products listed are free from defects in material and/or
workmanship only. Maxxima will replace any warrantied product to the original consumer/purchaser if the product fails because of defects
due to workmanship and/or materials within the limited warranty period. Limited warranty is not transferable and applies to the original
installation of the Maxxima product. This offer does not constitute in any way a product guarantee and Maxxima does not hereby assume
any obligation whatsoever beyond sending a free replacement product.
Risk of electric shock - Disconnect power at the source
before installation.
If you are unsure about the installation or the maintenance
of the wall light, please consult an electrician.
Do not make or alter any holes in the wiring enclosure or
modify any electrical componentry.
CAUTIONS
To insure personal safety, proper grounding of the
electrical fixture is required.
The fixture must be wired in accordance with the National
Electric Code and applicable local codes or ordinances.
Consult a qualified electrician to ensure correct branch
circuit conductor.
WARNINGS
1.
Ensure the power has been turned off by switching the circuit breaker
to the off position or by removing the fuse from the fuse panel.
2. If you are replacing an exisitng fixture, remove and disconnect
the old fixture first.
3. Mount the fixture mounting plate using the provided screws shown
as #2.
4. Connect the supply ground wire (green or bare copper) to the
fixture mounting plates using the provided green grounding screw
leaving some excess wire, then connect this excess to the
fixture ground wire (stranded bare copper) using the provided wire nut.
5. Connect the fixture neutral wire (white wire) to the supply
neutral wire (white wire) using the provided wire nut.
6. Connect the fixture hot wire (black wire) to the supply hot wire
(black wire) using the provided wire nut.
7. Mount the fixture assembly to the mounting bracket using the
provided screws #11 while ensuring no wires are being pinched or
misplaced.
8. Tighten the provided screws #11 until the fixture is secure.
9. Installation is now complete, restore power and
ensure the fixture is operational.
Note: this fixture is not approved to be used with dimmers.
1. Junction Box (not included)
2. Junction box screws
3. Fixture mounting plate
4. Neutral supply wire (white wire)
5. Hot supply wire (black wire)
6. Ground supply wire (green or bare copper)
7. Wire nut
8. Neutral fixture wire (white wire)
9. Hot fixture wire (black wire)
10. Ground fixture wire (standed bare copper)
11. Fixture mounting screw
12. Fixture assembly
  • Page 1 1

Maxxima MSL-17150RB Installation guide

Type
Installation guide
This manual is also suitable for

Maxxima MSL-17150RB is a 17” LED Picture Light designed for indoor use. It provides bright, even illumination for artwork, photographs, and other display items. The fixture is easy to install and can be mounted on a wall or ceiling. It has a durable construction and a 3-year warranty.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI