GetInLight IN-0317-3-SN-40 Installation guide

Brand: GetInLight

Model: IN-0317-3-SN-40

Category: Floodlights

Type: Installation guide

1 2

3 4

5 6

Package Contents

A 1

B 1

C 1

D 4

E 4

aa 1

bb 2

Warranty

5-YEAR LIMITED WARRANTY

The manufacturer warrants this product to be free from defects in materials and workmanship for a period of five (5) years from date of purchase. This

warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this products is found to be defective,

the manufacturer's only obligation, and your exclusive remedy, is the repair or replacement of the product at he manufacturer's discretion, provided that

the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect, or mishandling. This warranty shall not apply to

any product that is found to have been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product.

This warranty shall not apply to a failure of the product as a result an accident, misuse, abuse, negligence, alteration, or faulty installation, or any other

failure not relating to faulty material workmanship. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or

incidental loss or damage, including labor/expense costs involved in the replacement or repair of said product.

Piece Quantity

Fixture Pan

Acrylic Diffuser

Decorative Ring

L-angles

Thumb Nuts

Scews for Fixture Mounting

Wire Nuts

Description

Contact the Customer Service Team at [email protected] or visit www.getinlight.com

Installation Guide

Integrated LED

Flush Mount Fixture

Model #

IN-0317-1-XX-XX, IN-0317-2-XX-XX,

IN-0317-3-XX-XX, IN-0317-4-XX-XX.

ATTACH YOUR RECEIPT HERE

Purchase Date __________________

Contact the customer service department at [email protected]

We commit to respond to emails within 24 hours - and sooner, if possible!

We are devoted to solving problems and offering the best service to our customers.

Questions, problems, missing parts?

PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING

INSTALLATION AND RETAIN FOR FUTURE REFERENCE.

1 2

3 4

5 6

Safety Information

Pre-Installation

PLANNING INSTALLATION

TOOLS REQUIRED

● Phillips Screwdiver ● Ladder ● Safety Goggles

● Wire Cutter ● Wire Stripper

DIMMABLE FUNCTIONALITY

MAX. LOAD

600W

150W

300W

DV-603PG 600W

DVELV-600PLUTRON

LUTRON

PD-6WCL-WH

INCANDESCENT / HALOGEN

PART NO.

DVCL-153P

MANUFACTURER

LUTRON

DV-600P

INCANDESCENT / HALOGEN / CFL / LED

INCANDESCENT / CFL / LED

INCANDESCENT / HALOGEN

CFL / LED

MAGNETIC LOW VOLTAGE

MACL-153M

IMPORTANT SAFETY INSTRUCTIONS

LUTRON

TYPE

Note:

Safely dispose of packaging materials. Assistance

will be required to support fixture during

installation.

● To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings

and instructions included with and on the the fixture box and all fixture labels.

● Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.

● Commercial installation, service and maintenance of luminaires should be performed by a qualified licensed electrician.

● For Residental installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check

your local electrical code.

● DO NOT INSTALL DAMAGED PRODUCT!

● This fixture is intended to be connected to a properly installed and grounded UL listed junction box.

● These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with

installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for

the purchaser’s or owner’s purpose, this matter should be referred to Inlight Co. Ltd.

WARNING: RISK OF ELECTRICALSHOCK

● Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.

● Turn off the power when you perform any maintenance.

● Verify that supply voltage is correct by comparing it with the luminaire label information.

● Make all electrical and grounded connections in accordancewith the National Electrical Code and any applicable local code requrirements.

● All wiring connections should be capped with UL approved wire connectors.

CAUTION: RISK OF INJURY

● Wear gloves and safety glasses at all times when removing luminaire from carton,installing, servicing or performing maintenance.

● Avoid direct eye exposure to the light source while it is on.

● Account for small parts and destroy packing material, as these may be hazardous to children.

WARNING: RISK OF BURN

● Allow fixture to cool before handling. Do not touch enclosure or light source.

● Do not exceed maximum wattage marked on luminaire label.

● Follow all lamp manufacturer’s warnings, recommendations and restrictions for: driver type, burning position, mounting locations/methods,

replacement, and recycling.

CAUTION: RISK OF FIRE

● Keep combustible and other materials that can burn away from luminaire and lamp/lens.

Compare all parts with the parts listed in the package contents section. If any part appears missing or damaged, do not install and use this light. Contact

customer service.

This fixture is dimmable with most regular dimmers. Following dimmers tested to be compatible with this fixture, dimming range up to: 10%-100%.

If you are unfamiliar with electrical installations, it is recommended you have a qualified electrician do your installation.

***CONSULT A LOCAL LICENSED ELECTRICIAN OR ELECTRICAL CONTRACTOR IF YOU ARE NOT SURE ABOUT THE INSTALLATION.***

1 2

3 4

5 6

Mounting Location Disconnect Power

- - Place the wall switch to the "OFF" position. (Fig.1.)

- Depending on which type of fuse box you have in your home:

Fig.2.

Plan the layout of the fixtures and ensure power wiring is routed

to all installation locations.

A 3" or 4" junction box must be installed at each desired location

before installing the fixture.

Junction Box (Not included)

• 3" & 4" square or octagon

• At least 1/2” deep

Fig.3.

Unscrew the four thumb nuts from fixture Disassemble the fixture

- Twist counterclockwise to loosen the thumb nuts - Remove the decorative ring, L-angles and diffuser.

Remove the protection foam and discard it. Do not remove any

other parts.

- Remove the thumb nuts from fixture.

SECTION A: PREPARING FOR INSTALLATION

1 2

SECTION B: MOUNTING INSTALLATION

Note: To avoid damaging this product, place the components on

a soft, non-abrasive surface such as carpet or cardboard.

Diffuser

Thumb Nuts

Decorative Ring

Thumb Nuts

Diffuser

Protection Foam

Remove and discard it

Place either the main (Master) switch to the "OFF" position,

cutting off power to your entire home OR turn off the individual

switch that provides power to where the fixture will be installed

Place either the main (Msster) switch to the "OFF" position,

cutting off power to your entire home OR turn off the fuse

that provides power to where the fixture will be installed

Carefully unpack the fixture. Lay out all parts on a clean

surface.

Remove the old fixture.

Fig.1

Wall Switch

Fig.2

Breaker Panel

Fig.3

Fuse Box

L-angles

1 2

5 6

Connect the wires

- Pull the power supply wires out from the junction box, strip 3/8" of bare

power supply wires.

- Hold two wires of the same color(one from the fixture, one from the junction

box) next to each other and make sure the two stripped ends sit tightly against

each other to gurantee effective connection later (but do not twitst wires),

See .

- Push wires firmly into wire nut (bb). Use your fingers, twist wire nut clockwise until tight. Check for tightness by pulling wires, See .

- Ensure the connectors are spliced tightly and carefully push the spliced wires back into the junction box.

Ground Wire:

- For safety and proper operation, the fixture must be properly

grounded.(If house wiring does not include a ground wire,

consult your local electrical code for approved grounding methods).

- A green or bare copper ground wire is preattached to the fixture.

The fixture ground wire must be spliced to the green or bare

copper ground wire in the junction box using one of the wire

nuts (bb).

Power Wires:

- Connect the NEUTRAL supply wire (White) from the junction

box to the NEUTRAL fixture wire (White)

- Connect the HOT supply wire (Black) from the junction box

to the HOT fixture wire (Black)

SECTION B: MOUNTING INSTALLATION (CONT.)

Note: Ensure that no bare wires are exposed after making the

connections.

Install the hardware

- Use either the existing junction box screws or

the mounting screws (aa) included in the hardware kit.

- Drive the screws into the junction box until there is

abount 3/8 inch between the ceiling and the under

side of the screw head.

Note: This fixture does not use a mounting breaket to

secure it to the junction box.

3/8 in.

1 cm

Junction Box

(Not Included)

Scews

Wire Nuts

LED Driver

Note: 4-inch keyhole slots location illustrated.

Note: 16-inch or 18-inch fixture do not has

the 3-inch keyhole slots.

Note:

1 2

3 4

5 6

Do not use power tools to install the screws, and do

not overtighten the screws! Overtightening the screws

may cause the fixture to warp and thus make assemble

the fixture difficult.

Install the fixture

- Locate the keyhole slots on the fixture pan.

- Align the wider end of keyhole slots on the fixture pan with screw heads on

the mounting plate, push fixture pan towards the mounting plate until screw

heads go through the key hole slots.

- Once both screw heads have passed through the keyholes, twist the fixture pan,

until both screws are situated at the narrow end of the keyhole slots.

- Hold fixture pan in place and tighten the screws (aa) just enough

without distorting or damaging the fixture.

SECTION B: MOUNTING INSTALLATION (CONT.)

Front View

Twist Clockwise

to Lock

Rotate the fixture pan Secure the fixture

7 8

- Rotate the fixture pan to a desired angle to match the layout of

the room.

1 2

3 4

Assemble the fixture Rotate the fixture to the desired angle

- Turn on power at circuit breaker or fuse box.

Seat the diffuser in the decorative ring.

Place the diffuser and decorative ring against the fixture pan

mounted on the ceiling. The threaded end of each thumb will

need to pass through the holes in the ring for the ring to be

installed.

Once in place, hold both the diffuser and the ring in place,

attach the L-angles, then the thumb nuts to secure the

decorative ring.

- Turn the light switch on to activate the fixture.

Problem Possible Cause Corrective Action

Fixture doesn't light.

Fuse blows or circuit breaker trips when light is turned on.

Light flickers during dimming

SECTION B: MOUNTING INSTALLATION (CONT.)

Note: Assistance will be required to support the

diffuser during installation.

SECTION C: TROUBLESHOOTING

1. Power is off.

2. Defective wall Switch.

3. Bad connection

1. Check if power supply is on.

2. Replace switch.

3. Check wiring.

1. Overloaded circuit

2. Short circuit.

1. If wiring connections are loose or disconnected,

redo the connections. Make sure that there are no

exposed wire conductors.

2. Discontinue use and call customer service.

Check if dimmer being used is in

compatible dimmer list from "dimmer"

section

If dimmer is not on the list, replace it with a dimmer

listed.

V. 2019

Questions, problems, missing parts? Before returning to the store,

contact Inlight Customer Service

Retain this manual for future use.

[email protected]

is a trademark of Inlight Co. Ltd.

GetInLight IN-0317-3-SN-40 Installation guide

Brand: GetInLight

Model: IN-0317-3-SN-40

Category: Floodlights

Type: Installation guide

Download PDF

report

GetInLight IN-0317-3-SN-40 Installation guide

GetInLight IN-0317-3-SN-40 Installation guide

Related papers

Other documents