GetInLight 6 inch LED Disk Light, Dimmable, Flush Mount Or Recessed, Soft White 3000K, Matte Bronze Finish, ETL Listed, Wet Location Rated, IN-0301-2-BZ-30 … Installation guide

Brand: GetInLight

Model: 6 inch LED Disk Light, Dimmable, Flush Mount Or Recessed, Soft White 3000K, Matte Bronze Finish, ETL Listed, Wet Location Rated, IN-0301-2-BZ-30 …

Category: Floodlights

Type: Installation guide

Package Contents

A 1

B 1

C 2

aa 2

bb 3

Warranty

5-YEAR LIMITED WARRANTY

The manufacturer warrants this product to be free from defects in materials and workmanship for a period of five (5) years from date of purchase. This

warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this products is found to be defective,

the manufacturer's only obligation, and your exclusive remedy, is the repair or replacement of the product at he manufacturer's discretion, provided that

the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect, or mishandling. This warranty shall not apply to

any product that is found to have been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product.

This warranty shall not apply to a failure of the product as a result an accident, misuse, abuse, negligence, alteration, or faulty installation, or any other

failure not relating to faulty material workmanship. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or

incidental loss or damage, including labor/expense costs involved in the replacement or repair of said product.

Contact the Customer Service Team at [email protected] or visit www.getinlight.com

Fixture

Diffuser

Keyhole Covers

Mounting Screws

Wire Nuts

DescriptionPiece Quantity

This fixture is dimmable with most regular dimmers. Following dimmers tested to be compatible with this fixture, dimming range up to: 10%-100%.

If you are unfamiliar with electrical installations, it is recommended you have a qualified electrician do your installation.

Safety Information

● To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings

and instructions included with and on the the fixture box and all fixture labels.

● Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.

● Commercial installation, service and maintenance of luminaires should be performed by a qualified licensed electrician.

● For residental installation: If you are unsure about the in stallation or maintenance of the luminaires, consult a qualified licensed electrician and check

your local electrical code.

● DO NOT INSTALL DAMAGED PRODUCT!

● This fixture is intended to be connected to a properly installed and grounded UL listed junction box.

● These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with

installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for

the purchaser’s or owner’s purpose, this matter should be referred to Inlight Co. Ltd.

Dimmable Functionality

ATTACH YOUR RECEIPT HERE

Purchase Date __________________

Installation Guide

Integrated LED

Light Disk

Model #

IN-0301-2-XX-XX

Contact the customer service department at [email protected]

We commit to respond to emails within 24 hours - and sooner, if possible!

We are devoted to solving problems and offering the best service to our customers.

Questions, problems, missing parts?

PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING

INSTALLATION AND RETAIN FOR FUTURE REFERENCE.

WARNING: RISK OF ELECTRICALSHOCK

● Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.

● Turn off the power when you perform any maintenance.

● Verify that supply voltage is correct by comparing it with the luminaire label information.

● Make all electrical and grounded connections in accordancewith the National Electrical Code and any applicable local code requrirements.

● All wiring connections should be capped with UL approved wire connectors.

CAUTION: RISK OF INJURY

● Wear gloves and safety glasses at all times when removing luminaire from carton,installing, servicing or performing maintenance.

● Avoid direct eye exposure to the light source while it is on.

● Account for small parts and destroy packing material, as these may be hazardous to children.

WARNING: RISK OF BURN

● Allow fixture to cool before handling. Do not touch enclosure or light source.

● Do not exceed maximum wattage marked on luminaire label.

● Follow all lamp manufacturer’s warnings, recommendations and restrictions for: driver type, burning position, mounting locations/methods,

replacement, and recycling.

CAUTION: RISK OF FIRE

● Keep combustible and other materials that can burn away from luminaire and lamp/lens.

Tools Required

● Phillips Screwdiver ● Safety Goggles

● Wire Cutter ● Wire Stripper

IMPORTANT SAFETY INSTRUCTIONS

Note: Safely dispose of packaging materials. Assistance may be required to

support fixture during installation.

Safety Information

Mounting Location Disconnect Power

- Plan the layout of the fixtures and ensure power wiring is routed

to all installation locations.

- Place the wall switch to the "OFF" position. (Fig.1.)

- Depending on which type of fuse box you have in your home:

- A 4" junction box must beinstalled at each desired location

before installing the fixture

Fig.2. Place either the main (Master) switch to the "OFF" position,

cutting off power to your entire home OR turn off the individual

switch that provides power to where the fixture will be installed

Junction Box (Not included)

• 4" square or octagon

• At least 1/2” deep

Fig.3. Place either the main (Msster) switch to the "OFF" position,

cutting off power to your entire home OR turn off the fuse

that provides power to where the fixture will be installed

- Carefully unpack the fixture. Lay out all parts on a clean

surface.

- Remove the old fixture.

SECTION A: PREPARING FOR INSTALLATION

1 2

Fig.1

Wall Switch

Fig.2

Breaker Panel

Fig.3

Fuse Box

3/8 in.

1 cm

Remove the diffuser from fixture Install mounting plate

- Pull off the diffuser from fixture. The diffuser is retained with

friction snap features. No fasteners are required to install it.

Do not remove any other parts.

- Use either the existing junction box screws or the mounting

screws (aa) included in the hardware kit.

- Drive the screws into the Junction box until there is about

3/8 in. between the ceiling and the under side of the screw

head.

1 2

SECTION B: JUNCTION BOX MOUNTING INSTALLATION

WARNING: DO NOT REMOVE BARRIER LEN

FROM FIXTURE.

Fixture

Barrier Len

(DO NOT REMOVE IT)

Junction Box

(Not included)

Mounting

Screw

Connect the wires

- Pull the power supply wires out from the junction box (not included),

strip 3/8" of bare power supply wires.

Hold two wires of the same color(one from the fixture, one from the

junction box) next to each other and make sure the two stripped ends

sit tightly against each other to gurantee effective connection later

(but do not twitst wires), See .

Push wires firmly into wire nut (bb). Use your fingers, twist wire nut

lockwise until tight. Check for tightness by pulling wires, See .

Power Wires:

- Connect the Neutral (White) supply wire from the junction

box to the Neutral fixture wire (White)

- Connect the Hot (Black) supply wire from the junction box

to the Hot fixture wire (Black)

Ground Wire:

- For safety and proper operation, the fixture must be properly

grounded.

- A green or bare copper ground wire is pre-installed to the

fixture. The fixture ground wire must be spliced to the green

or bare copper ground wire in the junction box using one of

the wire nuts (bb).

Diffuser

Wire Nut

Wires From

the Fixture

Secure the fixture

- Locate the keyhole slots on the fixture.

- Align the wider end of keyhole slots on the fixture with screw heads on the junction box,

push fixture towards the junction box until screw heads go through the key hole slots.

Once both screw heads have passed through the keyholes, twist the housing, until both

screws are situated at the narrow end of the keyhole slots.

Hold fixture in place and tighten the screws just enough without distorting or damaging

the fixture.

Assemble the fixture

- Lift diffuser (B) up to housing assembly, secure the lens over the

fixture by snapping it into place.

- Turn on power at circuit breaker or fuse box.

- Turn the light switch on to activate the fixture.

WARNING:

RISK OF SHOCK - Do not operate fixture without barrier len

installed.

SECTION B: JUNCTION BOX MOUNTING INSTALLATION (CONT.)

Front View

Diffuser

Twist Clockwise

to Lock

Matintenance & Care

This LED light provides low maintenance service with no bulbs to change. Ensure that the power is disconnected prior to cleaning. Clean surface with alcohol

based cleaning products. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

- Snap the keyhole covers (C) into place to hide mounted screws.

Keyhole

covers

Questions, problems, missing parts? Before returning to the store,

contact Inlight Customer Service

Retain this manual for future use

[email protected]

Note: Do not use power tools to install the screws, and do not overtighten the

screws! Overtightening the screws may cause the fixture to warp.

is a trademark of Inlight Co. Ltd.

V. 2019

GetInLight 6 inch LED Disk Light, Dimmable, Flush Mount Or Recessed, Soft White 3000K, Matte Bronze Finish, ETL Listed, Wet Location Rated, IN-0301-2-BZ-30 … Installation guide

Brand: GetInLight

Model: 6 inch LED Disk Light, Dimmable, Flush Mount Or Recessed, Soft White 3000K, Matte Bronze Finish, ETL Listed, Wet Location Rated, IN-0301-2-BZ-30 …