2. Anova
  3. RCPG6

Anova RCPG6 Assembly Instruction

  • Hello! I am an AI chatbot trained to assist you with the Anova RCPG6 Assembly Instruction. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED:
• Ratchet with 9/16" socket
• Tape
• Level
Assembly Instructions
Recycled
RCPG6 - 6' Rectangular Picnic Table, Galvanized Legs
TABLE COMPONENTS:
ASSEMBLY HARDWARE: All hardware is stainless steel.
(3) Tabletop Planks
(1) Center Brace
Mount
(2) Seat Stiener
Supports
(2) Seat Planks (2) Angle Braces (2) Seat Stieners (2) Table Under Supports
(30) 3/8"-16 X 2 1/2"
Carriage Bolts
(1) 3/8"-16 X 1 1/2"
Carriage Bolt
(2) 3/8"-16 X 1"
Carriage Bolts
(33) 3/8"-16
Hex Nuts
(33) 3/8"Flat
Washers
ASSEMBLY:
Inspect the shipping container contents for damage and to determine that all components and hardware are present.1.
2. Lay all parts on a so work surface or on the shipping packaging to prevent damage to nish.
3. Locate the three tabletop planks and the two table under supports. The
tabletop planks can be distinguished from the seat planks because the
predrilled holes on either end of the tabletop planks are about 1 1/2”
closer to the end of the plank.
NOTE: Before assembling the nuts to the bolts, it is recommended that a light oil or petroleum jelly be applied to the screw threads.
1
6' Rectangular Picnic Table, Galvanized Legs
The assembly is a two-person operation.
2
4. Insert a 3/8"-16 X 2 1/2” carriage bolt through each of the holes in the tabletop
planks.
NOTE: It may be helpful to tape the bolt heads in place so the planks can be
adjusted without dislodging the bolts.
Place one of the table under supports over the line of carriage bolts. Make sure the
vertical ange on the mounting bar of the under support faces outward toward the
nearest end of the table. Place one 3/8" at washer and one 3/8"-16 hex nut on
the end of each carriage bolt and tighten nger tight.
Repeat this step to install the remaining under support on the other side.
Once all the hardware is installed be sure to check the alignment of the vertical
ange on the mounting bar before tightening the hex nuts with the ratchet and
9/16" socket.
5. Insert the 3/8"-16 X 1 1/2” carriage bolt through the hole in the center of the center
brace mount and hold or tape it in place and position the center brace mount over the
line of holes across the center of the tabletop. Insert 3/8"-16 X 2 1/2" carriage bolts
through the seat planks and center brace mount's mounting holes.
Place a 3/8" at washer and 3/8"-16 hex nut on each of the carriage bolts, except the
center one, and tighten them using the ratchet with the 9/16” socket.
6. Place the mounting hole of one of the angle braces over the carriage bolt in the
middle of the center brace mount. Align the hole on the other end of the brace
with the hole in the mounting plate on the under support. Insert one of the 3/8"-
16 X 1" carriage bolts through the mounting plate and angle brace and then place
a 3/8" at washer and 3/8"-16 hex nut on the end of the carriage bolt. Leave the
hardware nger tight so the tabletop can be adjusted and leveled later.
7. Repeat Step 6 to install the remaining angle brace, except place a 3/8" at washer
and 3/8"-16 hex nut on the 3/8"-16 X 1 1/2" carriage bolt in the center of the
center brace mount.
Leave the hardware nger tight so the tabletop can be adjusted and leveled later.
3/8"-16 X 2 1/2" Carriage Bolt
3/8"-16 X 2 1/2" Carriage Bolt
3/8"-16 X 1" Carriage Bolt Angle Brace
3/8"-16 X 1 1/2" Carriage Bolt
Center Brace Mount
3/8"-16 Hex Nut
3/8"-16 Hex Nut
3/8"-16 Hex Nut
3/8"-16 Hex Nut
Table Under Support
3/8" Flat Washer
3/8" Flat Washer
3/8" Flat Washer
3/8" Flat Washer
3
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
Manufactured in the U.S.Copyright 2019 ANOVA®10/25/2018
8. Insert six 3/8"-16 X 2 1/2" carriage bolts into one of the seat planks.
Place one of the seat stiener supports over the two carriage bolts in
the center of one of the seat planks. Place a 3/8" at washer and 3/8"-
16 hex nut on one of the carriage bolts and tighten with the wrench and
9/16" socket. Repeat this step for the other seat plank.
9. Raise one of the seat planks up to the seat mounting bracket on one of the under supports. Orient the seat plank so that the 3/8"-16 hex
nut and 3/8" at washer on the seat stiener support is toward the outside edge. Place a 3/8" at washer and 3/8"-16 hex nut on the end
of the two carriage bolts through the seat brackets on the outside edge of the seat plank. Leave the hardware nger tight until the seat
stiener is attached.
Place the seat stiener over the three carriage bolts on the inside edge of the seat plank and place a 3/8" at washer and 3/8"-16 hex nut
on each of the carriage bolts. Tighten all of the seat hardware with the ratchet and 9/16" socket.
Repeat this step to install the remaining seat plank to the other side of the table under supports.
10. Position the bench upright and move to the location where it will be used.
Aer two weeks, retighten all of the hardware.
3/8"-16 Hex Nut
3/8"-16 Hex Nut
3/8"-16 Hex Nut
Seat Stiener
3/8" Flat Washer
3/8" Flat Washer
3/8" Flat Washer
3/8"-16 X 2 1/2" Carriage Bolt
Seat Plank Seat Stiener Support
Assembly and Replacement Parts
Center Brace Mount
Angle Brace
Seat Plank
Seat Stiener Support
Seat Stiener
Table Under Support
Tabletop Plank
11.
/