2. Toro
  3. HD Vac Bagger Blower Cover, TITAN Zero-Turn-Radius Riding Mower

Toro HD Vac Bagger Blower Cover, TITAN Zero-Turn-Radius Riding Mower Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Toro HD Vac Bagger Blower Cover, TITAN Zero-Turn-Radius Riding Mower Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
FormNo.3439-702RevA
HDVacBaggerBlowerCover
TITAN
®
Zero-Turn-RadiusRidingMower
ModelNo.140-5036
InstallationInstructions
Safety
SafetyandInstructionalDecals
Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyarea
ofpotentialdanger.Replaceanydecalthatisdamagedormissing.
decal136-4164
136-4164
1.Warning—readtheOperator’sManual.4.Cutting/dismembermenthazard,impeller—keepawayfrom
movingparts;keepallguardsandcoversinplace.
2.Warning—hearingprotectionmustbeworn.
5.Cutting/dismembermenthazard,impeller—disengagethe
PTO,removethekey,andwaitforallmovingpartstostop.
3.Thrownobjecthazard—donotoperatetheblowerwithoutthe
entiresysteminstalledandlatched.
6.Warning;lossoftraction—donotoperatewithonly
counterbalanceweightsinstalled;donotoperatewithonly
E-ZVacinstalled;operateonlywithbothE-ZVacand
counterbalanceweightsinstalled.
©2020—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.
OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved
*3439-702*A
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescription
Qty.
Use
1
Nopartsrequired
–
Preparethemachine.
2
Nopartsrequired
–
Removetheexistingcover.
Cover
1
Hex-headbolt(1/4x5/8inch)
11
3
Locknut(1/4inch)
1
Installthenewcover.
1
PreparingtheMachine
NoPartsRequired
Procedure
1.Parkthemachineonalevelsurface.
2.Disengagetheblade-controlswitch.
3.Engagetheparkingbrake.
4.Movethemotion-controlleversoutwardtothe
NEUTRAL-LOCKposition.
5.Shutofftheengineandremovethekey.
2
2
RemovingtheExisting
Cover
NoPartsRequired
Procedure
Removetheexisting5shoulderscrews,5
Phillips-headscrews,blowerguard,andcoverfrom
theblowerassembly(Figure1).
Note:Youcandiscardtheseparts.
g321826
Figure1
1.Shoulderscrew
4.Blowerassembly
2.Existingcover5.Blowerguard
3.Phillips-headscrew
3
3
InstallingtheNewCover
Partsneededforthisprocedure:
1
Cover
11
Hex-headbolt(1/4x5/8inch)
1
Locknut(1/4inch)
Procedure
1.Alignthenewcoverwiththeholesontheblower
assembly.
2.Usingthecoverasthetemplate,drill1hole(6.4
mmor1/4inch)intotheblowerchute(Figure2).
g321825
Figure2
1.Drillahole(6.4mmor1/4inch)here.
3.Securethecovertotheblowerassemblyusing
the11hex-headbolts(1/4x5/8inch)and1
locknut(1/4inch)asshowninFigure3.
g322552
Figure3
1.Newcover3.Blowerassembly
2.Hex-headbolt(1/4x5/8
inch)
4.Locknut(1/4inch)
4
/