Rockwell Automation Allen-Bradley 1756-EN2TSC Installation Instructions Manual

EtherNet/IP Modules

Catalog Numbers 1756-ENBT, 1756-EN2F, 1756-EN2T, 1756-EN2TP, 1756-EN2TPXT, 1756-EN2TR, 1756-EN2TXT,

1756-EN2TRXT, 1756-EN2TSC, 1756-EN3TR, 1756-EWEB, 1768-ENBT, 1768-EWEB, 1769-AENTR

Installation Instructions

Important User Information

Read this document and the documents listed in the additional resources section about installation, configuration, and

operation of this equipment before you install, configure, operate, or maintain this product. Users are required to

familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws,

and standards.

Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required

to be carried out by suitably trained personnel in accordance with applicable code of practice.

If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be

impaired.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the

use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and

requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or

liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or

software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation,

Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

Labels may also be on or inside the equipment to provide specific precautions.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment,

which may lead to personal injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property

damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.

IMPORTANT

Identifies information that is critical for successful application and understanding of the product.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous

voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may

reach dangerous temperatures.

ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to

potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL

Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE).

Rockwell Automation Publication ENET-IN002H-EN-P - August 2017 3

Table of Contents

Summary of Changes New and Updated Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Preface Download the Add-on Profiles and Firmware. . . . . . . . . . . . . . . . . . . . . 7

Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Chapter 1

Install a 1756 EtherNet/IP

Communication Module

Installation Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Grounding Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Set the Network IP Address on a Module . . . . . . . . . . . . . . . . . . . . . . . 14

Determine Module Slot Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Install the Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Connect the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Use the following information to wire the module. . . . . . . . . . . . 17

Connect the Module to an EtherNet/IP Network Via an RJ45

Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Connect the Module to an EtherNet/IP Network Via a Fiber

Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Connect to the Module Via the USB Port . . . . . . . . . . . . . . . . . . . . . . . 19

Apply Chassis Power and Check Status Indicators . . . . . . . . . . . . . . . 19

Install or Remove the Module Under Power (RIUP) . . . . . . . . . . . . . 21

Chapter 2

Install a 1768 EtherNet/IP

Communication Module

Installation Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Grounding Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Set the Network IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Install the Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Mount the Module with Screws. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Mount on a DIN Rail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Wire the Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Connect the Module to an EtherNet/IP Network via an RJ45

Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Apply Chassis Power and Check Status Indicators . . . . . . . . . . . . . . . 30

Remove the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Chapter 3

Install a 1769 EtherNet/IP

Adapter

System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Example Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Installation Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Grounding Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Set the Network IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Install the Adapter in a 1769 System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Adapter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

System Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Mount the Adapter and I/O Modules . . . . . . . . . . . . . . . . . . . . . . . 41

4 Rockwell Automation Publication ENET-IN002H-EN-P - August 2017

Table of Contents

Wire the Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Remove or Replace the Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Chapter 4

Set the Network IP Address Set the Network IP Address with the Rotary Switches . . . . . . . . 46

Set the Network IP Address with the BOOTP/DHCP Server . . . . 47

Use DHCP Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Set the Network IP Address with RSLinx Software or the Studio 5000™

Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Reset the Module IP Address to a Factory Default Value . . . . . . 54

Chapter 5

Configure a Workstation to

Operate on an EtherNet/IP

Network

Select the Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Configure the Ethernet Communication Driver . . . . . . . . . . . . . . . . . 56

Chapter 6

USB Communication Set Up the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Configure a Module Via the USB Port . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Set Up a USB Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Load Firmware Through a USB Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Appendix A

1756 EtherNet/IP Status

Indicators

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Appendix B

1768 EtherNet/IP Module Status

Indicators

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Appendix C

1769 EtherNet/IP Adapter Status

Indicators

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Appendix D

Fiber Cable and LC Connector Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Rockwell Automation Publication ENET-IN002H-EN-P - August 2017 5

Summary of Changes

This manual contains new and updated information.

New and Updated

Information

This table contains the changes made in this revision.

Topic Page

Added graphic of the 1756-EN2TP Parallel Redundancy Protocol Ethernet Communication Module. 19

Added content about the 1756-EN2TP module status indicators. 63

6 Rockwell Automation Publication ENET-IN002H-EN-P - August 2017

Summary of Changes

Notes:

Rockwell Automation Publication ENET-IN002H-EN-P - August 2017 7

Preface

This manual describes how to install and start up EtherNet/IP module systems

with Logix5000

™

controllers.

Use this manual if you program applications that use an EtherNet/IP network

with one of these Logix5000 controllers:

• CompactLogix

™

• ControlLogix

®

Understand the following:

• Networking concepts

• How to the use Studio 5000

™

environment

• How to use RSLinx

®

Classic programming software

Download the Add-on

Profiles and Firmware

If a communication module has a later firmware revision than recognized in the

current version of the Logix Designer™ application, you must download the latest

firmware. When you download the Add-on Profile (AOP) for the module, it can

be recognized in the Controller Organizer.

Download the Add-on Profile and the latest module firmware from the Product

Compatibility and Download website at http://www.ab.com

.

If the procedure is performed while the web pages are already enabled, they

continue to be enabled and the password is reset to the serial number of the

adapter.

Additional Resources

For more information on the products that are described in this publication, use

these resources.

Resource Description

EtherNet/IP Modules Installation Instructions,

publication ENET-IN002

Provides information about how to complete these tasks with EtherNet/IP communication modules in

a Logix5000 control system:

• Install the module

• Configure initial application setup

• Troubleshoot application anomalies related to EtherNet/IP communication module use

EtherNet/IP Secure Communication User Manual,

publication ENET-UM003

Provides information on how to configure authentication, encryption, and firewalls, typical

architectures, and diagnostics for modules equipped with secure communication function.

Ethernet Design Considerations Reference Manual, publication ENET-RM002

Provides details about how to use EtherNet/IP communication modules with Logix5000 controllers

and communicate with other devices on the EtherNet/IP network.

EtherNet/IP Socket Interface Application Technique, publication ENET-AT002 Describes the socket interface that you can use to program MSG instructions. These instructions

communicate between a Logix5000 controller via an EtherNet/IP module and Ethernet devices that do

not support the EtherNet/IP application protocol. These include bar code scanners, RFID readers, or

other standard Ethernet devices.

EtherNet/IP Embedded Switch Technology Application Guide, publication

ENET-AP005

Provides details about how to install, configure, and maintain linear and Device Level Ring (DLR)

networks by using Rockwell Automation EtherNet/IP devices equipped with embedded switch

technology.

Troubleshoot EtherNet/IP Networks Application Technique, publication

ENET-AT003

Provides details about how to assign IP addresses to and how to troubleshoot EtherNet/IP networks

and devices.

8 Rockwell Automation Publication ENET-IN002H-EN-P - August 2017

Preface

You can view or download publications at

http:/www.rockwellautomation.com/literature/

. To order paper copies of

technical documentation, contact your local Allen-Bradley distributor or

Rockwell Automation sales representative.

EtherNet/IP Parallel Redundancy Protocol (PRP) Application Technique,

publication ENET-AT006

Provides details about how to install, and configure a Parallel Redundancy Protocol (PRP) networks by

using Rockwell Automation EtherNet/IP devices equipped with embedded switch technology.

EtherNet/IP Network Configuration User Manual, publication ENET-UM001 Describes how you can use EtherNet/IP communication modules with

your Logix5000 controller and communicate with various devices on the Ethernet network.

EtherNet/IP Media Planning and Installation Manual

This manual is available from the Open DeviceNet Vendor Association

(ODVA) at: http://www.odva.org.

Provides details about how to install, configure, and maintain linear and Device Level Ring (DLR)

networks by using Rockwell Automation® EtherNet/IP devices equipped with embedded switch

technology.

Resource Description

Rockwell Automation Publication ENET-IN002H-EN-P - August 2017 9

Preface

Notes:

10 Rockwell Automation Publication ENET-IN002H-EN-P - August 2017

Preface

Rockwell Automation Publication ENET-IN002H-EN-P - August 2017 11

Chapter 1

Install a 1756 EtherNet/IP Communication

Module

Topic Page

Installation Summary 14

Install the Module 16

Determine Module Slot Location 15

Install the Module 16

Connect the Module 17

Connect to the Module Via the USB Port 19

Apply Chassis Power and Check Status Indicators 19

Install or Remove the Module Under Power (RIUP) 21

ATTENTION: Environment and Enclosure

This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined

in IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating.

This equipment is not intended for use in residential environments and may not provide adequate protection to radio communication

services in such environments.

This equipment is supplied as open-type equipment. It must be mounted within an enclosure that is suitably designed for those

specific environmental conditions that will be present and appropriately designed to prevent personal injury resulting from

accessibility to live parts. The enclosure must have suitable flame-retardant properties to prevent or minimize the spread of flame,

complying with a flame spread rating of 5VA or be approved for the application if nonmetallic. The interior of the enclosure must be

accessible only by the use of a tool. Subsequent sections of this publication can contain additional information regarding specific

enclosure type ratings that are required to comply with certain product safety certifications.

In addition to this publication, see the following:

• Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1

, for additional installation requirements

• NEMA 250 and IEC 60529, as applicable, for explanations of the degrees of protection provided by enclosures

12 Rockwell Automation Publication ENET-IN002H-EN-P - August 2017

Chapter 1 Install a 1756 EtherNet/IP Communication Module

North American Hazardous Location Approval

The following information applies when operating this

equipment in hazardous locations.

Informations sur l’utilisation de cet équipement en

environnements dangereux.

Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for use in Class

I Division 2 Groups A, B, C, D, Hazardous Locations and nonhazardous

locations only. Each product is supplied with markings on the rating

nameplate indicating the hazardous location temperature code.

When combining products within a system, the most adverse

temperature code (lowest "T" number) may be used to help

determine the overall temperature code of the system. Combinations

of equipment in your system are subject to investigation by the local

Authority Having Jurisdiction at the time of installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne conviennent qu'à

une utilisation en environnements de Classe I Division 2 Groupes A, B,

C, D dangereux et non dangereux. Chaque produit est livré avec des

marquages sur sa plaque d'identification qui indiquent le code de

température pour les environnements dangereux. Lorsque plusieurs

produits sont combinés dans un système, le code de température le

plus défavorable (code de température le plus faible) peut être utilisé

pour déterminer le code de température global du système. Les

combinaisons d'équipements dans le système sont sujettes à

inspection par les autorités locales qualifiées au moment de

l'installation.

WARNING: EXPLOSION HAZARD

• Do not disconnect equipment unless power has

been removed or the area is known to be

nonhazardous.

• Do not disconnect connections to this equipment

unless power has been removed or the area is

known to be nonhazardous. Secure any external

connections that mate to this equipment by using

screws, sliding latches, threaded connectors, or

other means provided with this product.

• Substitution of components may impair suitability

for Class I, Division 2.

• If this product contains batteries, they must only

be changed in an area known to be nonhazardous.

AVERTISSEMENT: RISQUE D’EXPLOSION –

• Couper le courant ou s'assurer que

l'environnement est classé non dangereux avant

de débrancher l'équipement.

• Couper le courant ou s'assurer que

l'environnement est classé non dangereux avant

de débrancher les connecteurs. Fixer tous les

connecteurs externes reliés à cet équipement à

l'aide de vis, loquets coulissants, connecteurs

filetés ou autres moyens fournis avec ce produit.

• La substitution de composants peut rendre cet

équipement inadapté à une utilisation en

environnement de Classe I, Division 2.

• S'assurer que l'environnement est classé non

dangereux avant de changer les piles.

Rockwell Automation Publication ENET-IN002H-EN-P - August 2017 13

Install a 1756 EtherNet/IP Communication Module Chapter 1

European Hazardous Location Approval

The following applies when the product bears the Ex Marking.

This equipment is intended for use in potentially explosive atmospheres as defined by European Union Directive 94/9/EC and has been found to comply with the

Essential Health and Safety Requirements relating to the design and construction of Category 3 equipment intended for use in Zone 2 potentially explosive

atmospheres, given in Annex II to this Directive.

Compliance with the Essential Health and Safety Requirements has been assured by compliance with EN 60079-15 and EN 60079-0.

WARNING: Special Conditions for Safe Use

• This equipment shall be mounted in an ATEX Zone 2 certified enclosure with a minimum ingress protection rating of at least

IP54 (as defined in EN 60529) and used in an environment of not more than Pollution Degree 2 (as defined in EN 60664-1)

when applied in Zone 2 environments. The enclosure must be accessible only by the use of a tool.

• This equipment shall be used within its specified ratings defined by Rockwell Automation.

• Secure any external connections that mate to this equipment by using screws, sliding latches, threaded connectors, or other

means provided with this product.

• Do not disconnect equipment unless power has been removed or the area is known to be nonhazardous.

• The USB port is intended for temporary local programming purposes only and not intended for permanent connection and do

not use the USB port in hazardous locations.

• Provision shall be made to prevent the rated voltage from being exceeded by transient disturbances of more than 140% of the

rated voltage when applied in Zone 2 environments.

• This equipment must be used only with ATEX-certified Rockwell Automation backplanes.

• The instructions in the user manual shall be observed.

ATTENTION: Prevent Electrostatic Discharge

This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these

guidelines when you handle this equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation, if available.

• Store the equipment in appropriate static-safe packaging when not in use.

ATTENTION: This equipment is not resistant to sunlight or other sources of UV radiation.

14 Rockwell Automation Publication ENET-IN002H-EN-P - August 2017

Chapter 1 Install a 1756 EtherNet/IP Communication Module

Installation Summary

Follow these steps to install a communication module in a 1756 ControlLogix®

chassis.

1. Set the Network IP Address on a Module

.

2. Determine Module Slot Location

.

3. Install the Module

.

4. Connect the Module

.

5. Apply Chassis Power and Check Status Indicators

.

6. Install or Remove the Module Under Power (RIUP)

. - Optional

If needed, see Download the Add-on Profiles and Firmware on page 7

.

Grounding Considerations

The grounding and bonding must be of equal potential between all devices in the

communication coverage area.

Set the Network IP Address

on a Module

To operate an EtherNet/IP communication module on an EtherNet/IP network,

you must set a network IP address.

ATTENTION: If this equipment is used in a manner that is not specified by the

manufacturer, the protection that is provided by the equipment can be

impaired.

Rockwell Automation Publication ENET-IN002H-EN-P - August 2017 15

Install a 1756 EtherNet/IP Communication Module Chapter 1

Figure 1 - How the IP Address for the Module is Set

See Set the Network IP Address on page 45 to view all steps for setting the IP

address.

Determine Module Slot

Location

Install the communication module in any slot in a ControlLogix® or

ControlLogix-XT™ chassis. You can install multiple communication modules in

the same chassis.

This example shows the chassis slot numbering in a 4-slot ControlLogix chassis

and a 5-slot ControlLogix-XT™ chassis. Slot 0 is the first slot and is always the

leftmost slot in the chassis.

Module Powerup

Module has an IP

address.

Switches set

from

001…254?

YesNo

Is DHCP or

BOOTP

enabled?

YesNo

Module requests

address from DHCP/

BOOTP server.

Module uses IP address

stored in nonvolatile

memory.

20806

Slot 2Slot 0

Slot 1 Slot 3

ControlLogix Chassis ControlLogix-XT Chassis

31896

Slot 0 Slot 4Slot 1 Slot 2 Slot 3

16 Rockwell Automation Publication ENET-IN002H-EN-P - August 2017

Chapter 1 Install a 1756 EtherNet/IP Communication Module

Install the Module

Follow these steps to install the module.

1. Align the circuit board with top and bottom guides in the chassis.

2. Slide the module into the chassis.

WARNING: When you insert or remove the module while backplane power is

on, an electric arc can occur. An electrical arc can cause an explosion in

hazardous location installations.

Be sure that power is removed or the area is nonhazardous before proceeding.

Repeated electrical arcs causes excessive wear to contacts on both the module and

its mating connector. Worn contacts can create electrical resistance that can affect

module operation.

ATTENTION: Use caution when handling the module. One side of the module is

a heat sink and can be hot.

IMPORTANT

Your module resembles one of the modules that are shown in the illustrations. The

extreme temperature (XT) versions of the modules are not shown in the

illustrations.

32455

Rockwell Automation Publication ENET-IN002H-EN-P - August 2017 17

Install a 1756 EtherNet/IP Communication Module Chapter 1

Make sure that the module backplane connector properly connects to the

chassis backplane. The module is properly installed when it is flush with

the power supply or other installed modules.

Connect the Module

Use the following information to wire the module.

Connect the Module to an EtherNet/IP Network Via an RJ45

Connection

Wire the RJ45 connector as shown.

Follow these steps to connect the module to the network.

WARNING: If you connect or disconnect the communication cable with power

that is applied to this module or any device on the network, an electric arc can

occur. An electric arc can cause an explosion in hazardous location

installations.

Be sure that power is removed or the area is nonhazardous before proceeding.

8 ------ NC

7 ------ NC

6 ------ RD-

5 ------ NC

4 ------ NC

3 ------ RD+

2 ------ TD-

1 ------ TD+

18 Rockwell Automation Publication ENET-IN002H-EN-P - August 2017

Chapter 1 Install a 1756 EtherNet/IP Communication Module

1. Attach the cable with the RJ45 connector to the Ethernet port on the

module as shown.

2. Attach the other end of the cable to the devices in your network.

Connect the Module to an EtherNet/IP Network Via a Fiber Connector

Attach the LC2 multimode fiber cable to the Ethernet port on the bottom of the

module as shown.

ATTENTION: Do not look directly into the optical port. When you view the

optical port under certain conditions, can expose the eye to hazard. When

viewed under some conditions, the optical port can expose the eye beyond the

maximum permissible exposure recommendations.

Class 1 laser product. Laser radiation is present when the system is open and

interlocks bypassed. Only trained and qualified personnel are allowed to install,

replace, or service this equipment.

Dual-port Module

(Single port not shown)

32457

Dual-port

Module

Single-port

Module

Rockwell Automation Publication ENET-IN002H-EN-P - August 2017 19

Install a 1756 EtherNet/IP Communication Module Chapter 1

Connect to the Module Via

the USB Port

If the module has a USB port, is it a Type B receptacle. To use the USB port, you

must have RSLinx® Classic software, version 2.55 or later, installed on your

computer.

Use a USB cable to connect your computer to the USB port. You can download

programs to controllers and configure Ethernet modules directly from your

computer over a USB connection.

For more information about USB setup and configuration, see Chapter 6, USB

Communication on page 59.

Apply Chassis Power and

Check Status Indicators

Before you apply power, you must install and connect a ControlLogix chassis and

power supply.

Follow these steps to apply power.

1. Flip the switch to the ON position.

WARNING: Do not use the USB port in hazardous locations.

ATTENTION: The USB port is intended for temporary local programming

purposes only and not intended for permanent connection. The USB cable is not

to exceed 3.0 m (9.84 ft) and must not contain hubs. The USB cable can be

ordered from Rockwell Automation, catalog number 9300-USBCBL-ABHR.

32458

20 Rockwell Automation Publication ENET-IN002H-EN-P - August 2017

Chapter 1 Install a 1756 EtherNet/IP Communication Module

2. To determine that the power supply and module are operating properly,

check the power supply and Module Status indicators and alphanumeric

display.

The alphanumeric display cycles through the following states: TEST -

PASS - OK - REV x.x, where x.x is the firmware revision of the module.

The display then alternates between OK and port link status for both

ports.

This graphic shows the front of the module for these modules (extended-

temperature versions [catalog numbers 1756-EN2TXT and 1756-

EN2TRXT] not shown).

LINK

NET

OK

32452

NET

OK

1

LNK1LNK1 LNK2LNK2 NETNET

OKOK

LNK1LNK1

1

2

LNK2

NETNET OKOK

3245332453

Single-port

Module

Dual-port

Module

LINKLINK

NETNET

OKOK

Single-port

Module

Dual-port

Module

32730

1756-EN2TP

Page is loading ...

Rockwell Automation Allen-Bradley 1756-EN2TSC Installation Instructions Manual

Rockwell Automation Allen-Bradley 1756-EN2TSC Installation Instructions Manual

Related papers

Other documents