urmet domus MT124-017 Technical Manual

Brand
urmet domus
Model
MT124-017
Category
Door intercom systems
Type
Technical Manual
PANELS
sec.3a
−−−−
1
2GO! - Technical manual
PANEL
PROGRAMMING MENU CAMERA AND DOOR UNIT
WITH 2 BUTTONS Ref. 1082/72 ......................................................2
Performance .................................................................................2
Structure .......................................................................................2
Description of terminal boards .....................................................2
Technical specifi cations ...............................................................2
Default programming ....................................................................3
Function ........................................................................................3
Volume regulation .........................................................................3
Camera lens direction adjustment ................................................3
Fron panel with 1 button ..............................................................4
DOOR UNIT MODULE Ref. 1082/7 .................................................4
Structure .......................................................................................4
Description of terminal boards .....................................................4
Technical specifi cations ...............................................................4
Default programming ....................................................................4
Function ........................................................................................5
Volume regulation .........................................................................5
16-PUSHBUTTON EXPANSION MODULE Ref. 1038/17 .................5
Wiring diagram .............................................................................5
Description of terminals ................................................................5
Technical specifi cations ...............................................................5
PRODUCT LIST ................................................................................6
INSTALLATION .................................................................................6
DIMENSIONS - Flush-mounted version - Wall-mounted version ....9
VIDEO DOOR PHONE SYSTEM -
Example of modular constructions with various capacities ...........10
DOOR PHONE SYSTEM -
Example of modular constructions with various capacities ...........12
SECTION 3A
(REV.D)
Download from www.urmetdomus.com Technical Manuals area.
SECTION CONTENTS
Some products may be described in the “New” section.§
2
−−−−
sec.3a
2GO! - Technical manual
PANELS
SINTHESI PANEL
SINTHESI PANEL
The module consists of anodised aluminium profi le modular elements
which can be fi tted in specifi c frames.
Furthermore, the fl ush-mounting boxes can be coupled by means of
shims to create various panel types and confi gurations with a small
number of components. The advantage of needing to stock fewer
components is relevant for both wholesalers and installers.
Furthermore, the door phone version can be installed either vertically
or horizontally to adapt to all architectural needs.
Module installation is simple thanks to the pre-wired connections on
the modules and system terminal boards on extractable carriages.
All Sinthesi products, characteristics and installation procedures are
shown in “Technical product manual - door phone and video door
phone systems” in the “Sinthesi panels” section.
CAMERA AND DOOR UNIT WITH 2 BUTTONS
Ref. 1082/72
Signalling
yellow LED
PERFORMANCE
Installable in Sinthesi frames with 2 modules.
Two pre-wired calling buttons.
Possibility of installing 2 expansion modules (connected in series)
for up to 32 user buttons in each door unit.
Connection with 16 user expansion module Ref. 1038/17 and
connector.
Possibility of connecting up to three door units in system.
Fixed focus colour camera with integrated optics and shutter.
Possibility of adjusting lens direction.
Integrated subject light.
Possibility of code sequences to calling buttons using dip
switches.
Programming entirely with dip switches also when device is not
powered.
Possibility of programming one or more buttons for controlling a
special decoder (“staircase lights” function).
60 second pick-up waiting time (system busy).
2 minute maximum conversation time from handset pick-up.
Call and end of conversation confi rmation tones.
Busy system optical and acoustic indications.
Lock control actuator with capacitance pulse discharge.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Free and privacy function electrical lock management.
Arrangement for activating electrical lock by pressing button inside
hall.
Open door sensor input.
Speaker and microphone volume adjustment trimmer.
Installation test function terminals.
Management of external coaxial video input for surveillance
cameras.
Relay box control for cyclic management of several surveillance
cameras.
Power output for name card lighting (up to 36 draw units with power
unit Ref. 1082/20).
STRUCTURE
REAR VIEW
LINE
ILL
SP
GND
T
GND
V3
V5
TST
SE+
SE-
PA
GND
Z CODE
VER.
ID
AUX
1 2 3 4 5
ON
1 2
ON
ON
12
ON
DIP
EXP
ON
Z CODE
ID
AUX
1 2 3 4 5
ON
1 2
ON
ON
12
ON
DIP
EXP
ON
2
1
3
4
5
6
1
Line terminal switch
2
User code dip switch
3
Door unit ID dip switch
4
Electrical lock operating mode and station type dip switch
5
Terminal board
6
Fonic level regulation
DESCRIPTION OF TERMINAL BOARDS
LINE
}
Non-polarised bus line
LINE
SE+ Positive electrical lock operation
SE- Negative electrical lock operation
ILL
}
Name card light power
ILL
PA Hall door opener button input
SP Open door sensor contact input
T Ref. 1038/69 relay box output for surveillance camera cycle
function
TST Test function terminal
GND
}
Reference ground for PA, T, TST, SP
GND
GND
V3
}
Secondary surveillance camera connection
V5
TECHNICAL SPECIFICATIONS
Max. Active consumption
(video + audio + 32 name tag light): 650mA
Max. Active consumption (video + audio): 400mA
Max. stand-by consumption: 80mA
Line termination: 104,4 Ohm±1%
Shooting sensor: CCD 1/3”
Built-in lens: series mounted
Octurator: series mounted
Focus: fi xed
Minimum lighting for an acceptable image: 0,2lux
Working temperature range: -10 ÷ 50°C
•
•
•
•
•
•
•
•
SINTHESI PANEL
CAMERA AND DOOR UNIT WITH 2 BUTTONS Ref. 1082/72
sec.3a
−−−−
3
2GO! - Technical manual
PANELS SINTHESI PANEL
SINTHESI PANEL
CAMERA AND DOOR UNIT WITH 2 BUTTONS Ref. 1082/72
DEFAULT PROGRAMMING
The default settings of the device are:
Door unit number: 1
Station type: Main
Electrical lock management: Privacy
First button user code: 0
Line termination: ON
ON
OFF
Z CODE
ID
AUX
12345
ON
12
ON
12
ON
DIP
FUNCTION
CALL FORWARDING
Up to 32 users can be called by pressing the corresponding buttons
on the panel associated to the camera Ref. 1082/72.
The following cases may occur when a call button is pressed according
to the state of the door unit:
The line is free: the door unit will output the call forwarding tone (3
beeps in sequence). The door unit will output an end of conversation
tone (5 beeps in rapid sequence) at the end of the communication.
The line is busy: the door unit will output a warning tone (5 beeps
in sequence) and the yellow LED on the front will blink until busy
mode ends. Press the call button again when busy mode ends.
ELECTRICAL LOCK MANAGEMENT
The door units have two terminals for electrical lock capacitance
discharge (SE-, SE+). The electrical lock is controlled in the following
cases:
Whenever the hall button is pressed (terminals PA, GND).
When a door open command is received from an apartment station
according to the confi guration of the AUX dip switch “free” or
“privacy” (see “2GO! system” paragraph “Door unit functions”).
Use timer Ref. 1032/81 to control electrical locks requiring longer
timing.
VOLUME REGULATION
Volume levels are calibrated by default so not to require adjustments
in most cases.
Use a screwdriver to adjust the trimmers if required.
J2
GT2
GT3
GT4
0~
12~
J2
GT2
GT3
GT4
0~
12~
Z
CODE
ID
AUX
1
2
3
4
5
ON
1
2
ON
ON
1
2
ON
DIP
EXP
ON
•
•
•
•
CAMERA LENS DIRECTION ADJUSTMENT
After installation, the camera direction can be adjusted according
to the position of the framed subject. This operation may be carried
out manually after removing the frame and the extractable front by
adjusting the jointed mount directly from the front. The frame does not
need to be tipped and special tools are not required.
IMAGING ANGLES
Rocking angles of the camera with respect to central position are:
VERTICAL +10 TO -15°
HORIZONTAL +10 TO -10°
50
0
50
7
22
34
-40
-21
-12
+21
-46
+32
-32
+46
-21
HORIZONTAL
VERTICAL
+10°
+10°
0
-15°
-10°0
0
Measurements in centimetres
4
−−−−
sec.3a
2GO! - Technical manual
PANELS
SINTHESI PANEL
SINTHESI PANEL
DOOR UNIT MODULE Ref. 1082/7
FRONT PANEL WITH 1 BUTTON
To make a camera unit with door unit and 1 button, procure a
Ref. 1745/107 front panel and install it as shown below:
Ref. 1082/72
Ref. 1745/107
In this case, press the button to call the apartment station with
code CODE +1 (code sent on video module).
DOOR UNIT MODULE Ref. 1082/7
PERFORMANCE
Installable in Sinthesi frames.
Possibility of installing 2 expansion modules (connected in series)
for up to 32 user buttons in each door unit.
Connection with 16 user expansion module Ref. 1038/17 and
connector.
Programming entirely with dip switches also when device is not
powered.
Possibility of code sequences to calling buttons using dip
switches.
Possibility of programming one or more buttons for controlling a
special decoder (“staircase lights” function).
60 second pick-up waiting time (system busy).
2 minute maximum conversation time from handset pick-up.
Call and end of conversation confi rmation tones.
Busy system optical and acoustic indications.
Lock control actuator with capacitance pulse discharge.
Free and privacy function electrical lock management.
Arrangement for activating electrical lock by pressing button inside
hall.
Open door sensor input.
Speaker and microphone volume adjustment trimmer.
Power output for name card lighting (up to 36 draw units with power
unit Ref. 1082/20).
§
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
STRUCTURE
ON
12
ON
12
DIP
45
ON
23
ON
1
ONDIPONON
4321 5 21
ON
2
1
1 2 3
4
SE+
SE-
GND
GND
LINE
ILL
PA
SP
EXP
Sch.1082/7
ON
Sett/Fab
Z
VER.
5
6
FRONT VIEW REAR VIEW
7
1
User code dip switch
2
Door unit ID dip switch
3
Electrical lock operating mode and station type dip switch
4
Fonic level regulation
5
Line terminal switch
6
Terminal board
7
Signalling yellow LED
DESCRIPTION OF TERMINAL BOARDS
LINE
}
Non-polarised bus line
LINE
SE+ Positive electrical lock operation
SE- Negative electrical lock operation
ILL
}
Name card light power
ILL
PA Hall door opener button input
SP
Open door sensor contact input
(not available at the moment)
GND
}
Reference ground for PA, SP
GND
TECHNICAL SPECIFICATIONS
Max. Active consumption
(audio + 16 name tag light): 250mA
Max. Active consumption (audio): 100mA
Max. stand-by consumption: 20mA
Line termination: 104,4 Ohm±1%
Working temperature range: -10 ÷ 50°C
DEFAULT PROGRAMMING
The default settings of the device are:
Door unit number: 2 (slave)
Station type: Main
Electrical lock management: Privacy
First button user code: 0
Line termination: ON
CODE
AUX
12345
ON
12
ON
ON
OFF
ID
12
ON
Z
sec.3a
−−−−
5
2GO! - Technical manual
PANELS SINTHESI PANEL
SINTHESI PANEL
DOOR UNIT MODULE Ref. 1082/7
16-PUSHBUTTON EXPANSION MODULE Ref. 1038/17
FUNCTION
CALL FORWARDING
Up to 32 users can be called by pressing the corresponding buttons
on the panel associated to the door unit module Ref. 1082/7.
The following cases may occur when a call button is pressed according
to the state of the door unit:
The line is free: the door unit will output the call forwarding tone (3
beeps in sequence). The door unit will output an end of conversation
tone (5 beeps in rapid sequence) at the end of the communication.
The line is busy: the door unit will output a warning tone (5 beeps
in sequence) and the yellow LED on the front will blink until busy
mode ends. Press the call button again when busy mode ends.
ELECTRICAL LOCK MANAGEMENT
The door units have two terminals for electrical lock capacitance
discharge (SE-, SE+). The electrical lock is controlled in the following
cases:
Whenever the hall button is pressed (terminals PA, GND).
When a door open command is received from an apartment station
according to the confi guration of the AUX dip switch “free” or
“privacy” (see “2GO! system” paragraph “Door unit functions”).
Use timer Ref. 1032/81 to control electrical locks requiring longer
timing.
VOLUME REGULATION
Volume levels are calibrated by default so not to require adjustments
in most cases.
Use a screwdriver to adjust the trimmers if required.
16-PUSHBUTTON EXPANSION MODULE
Ref. 1038/17
To
the door unit
Sch. 1038/17
OUTPUT INPUT
Sch. 1038/17
OUTPUT INPUT
Terminals for
users buttons
The extension module can be used to add 16 user buttons to the
door unit.
Arrange the device on the push-button panels, as shown in the
following fi gure.
Connect the user buttons and connect the device to the door unit
and to other extensions by means of the specifi c wire. Respect the
connections and the holes in the fl ush mounting boxes.
Ref. 1038/17
Fasten on the bottom of the fl ush-mounting box.
•
•
•
•
IMPORTANT: Fasten the expansion module near button, blank or
repertory modules.
WIRING DIAGRAM
8
2
16 User
expansion
module
To following
expansion
modules
To following
module
to the power
supply
~12
G/T
G/T U4
U2
U3
U1
~12
~0
~0
U1
~0
U3
U4G/T
G/T
~12
~0
~12
U2
InputOutput
C
P1
P2
P3
C
P14
P15
P16
P4
P5
P6
P7
P8
P13
P12
P11
P10
P9
~12
G/T
G/T U4
U2
U3
U1
~12
~0
~0
U1
~0
U3
U4G/T
G/T
~12
~0
~12
U2
Output
C
P1
C
P16
T
GND
GND
V5
V3
SE-
SE+
PA
GND
SP
TST
LINE
ILL
EXP
DESCRIPTION OF TERMINALS
C Electrical reference earth
P1...P16 User buttons
TECHNICAL SPECIFICATIONS
Consumption: 1mA Max
Current in user button: ~1mA
Working temperature range: +0°C ÷ +50°C
Humidity: 90% UR a 30 °C
6
−−−−
sec.3a
2GO! - Technical manual
PANELS
SINTHESI PANEL
INSTALLATION
You are advised to install the modules at the heights shown below
according to the required system confi guration.
1,55 ÷ 1,60 m 1,55 ÷ 1,60 m
1,55 ÷ 1,60 m
In any case, consider the height shown in the fi gure for fastening the
camera for correct installation of complex arrangement with several
modules. The height refers to the door unit in door phone systems.
The procedure for horizontal panel development (possible only for
door phone systems) is the same at that shown below for vertical
development.
Obviously, in this case, the boxes, module holders, modules and
frames must be turned by 90°.
Arrange the hole (on the bottom or on the sides) for letting through
the connection wires before closing the fl ush-mounting box (single or
joined to other boxes).
PRODUCT LIST
All Sinthesi products, characteristics and installation procedures are
shown in “Technical product manual - door phone and video door
phone systems” in the “Sinthesi panels” section.
PUSH BUTTON AND REPERTORY
With 1 key Ref. 1145/11
With 2 keys Ref. 1145/12
With 3 keys Ref. 1145/13
With 4 keys Ref. 1145/14
With 4 keys doppi Ref. 1145/18
Modulo repertorio Ref. 1145/50
Modulo cieco Ref. 1145/59
EMBEDDING BOX
For 2 modules Ref. 1145/52
For 3 modules Ref. 1145/53
For 4 modules Ref. 1145/54
FRAMES AND MODULE HOLDERS
For 2 modules Ref. 1145/62
For 3 modules Ref. 1145/63
For 4 modules Ref. 1145/64
WALL COVER FRAME
For 2 modules Ref. 1145/712
For 3 modules Ref. 1145/713
For 4 modules Ref. 1145/714
For 4 modules (2 frames for 2 modules) Ref. 1145/724
For 6 modules (2 frames for 3 modules) Ref. 1145/726
For 8 modules (2 frames for 4 modules) Ref. 1145/728
For 9 modules (3 frames for 3 modules) Ref. 1145/739
For 12 modules (3 frames for 4 modules) Ref. 1145/732
RAIN HOOD
For 2 modules Ref. 1145/612
For 3 modules Ref. 1145/613
For 4 modules Ref. 1145/614
For 4 modules (2 frames for 2 modules) Ref. 1145/624
For 6 modules (2 frames for 3 modules) Ref. 1145/626
For 8 modules (2 frames for 4 modules) Ref. 1145/628
For 9 modules (3 frames for 3 modules) Ref. 1145/639
For 12 modules (3 frames for 4 modules) Ref. 1145/632
CASE AND HOOD
For 2 modules Ref. 1145/312
For 3 modules Ref. 1145/313
For 4 modules Ref. 1145/314
For 4 modules (2 frames for 2 modules) Ref. 1145/324
For 6 modules (2 frames for 3 modules) Ref. 1145/326
For 8 modules (2 frames for 4 modules) Ref. 1145/328
For 9 modules (3 frames for 3 modules) Ref. 1145/339
For 12 modules (3 frames for 4 modules) Ref. 1145/332
CASE AND HOOD FOR SEMI-FLUSHED GATE INSTALLATION
For 2 modules Ref. 1145/342
For 3 modules Ref. 1145/343
POSTAL BOX
For 2 modules (horizontal) Ref. 1145/41
For 2 modules (vertical) Ref. 1145/42
SINTHESI PANEL
PRODUCT LIST
INSTALLATION
sec.3a
−−−−
7
2GO! - Technical manual
PANELS SINTHESI PANEL
Fit the fl ush mounting box in line with the wall: it must not project.
Fit the module holder frame.
4 mm
A
Fit the modules in the frame.
•
•
•
SINTHESI PANEL
INSTALLATION
Turn the frame round and connect wires.
J2
GT2
GT3
GT4
0~
12~
J2
GT2
GT3
GT4
0~
12~
Z
CODE
ID
AUX
1
2
3
4
5
ON
1
2
ON
ON
1
2
ON
DIP
EXP
ON
Set the dip switches as shown in the “System installation and
activation” section.
J2
GT2
GT3
GT4
0~
12~
J2
GT2
GT3
GT4
0~
12~
Z
CODE
ID
AUX
1
2
3
4
5
ON
1
2
ON
ON
1
2
ON
DIP
EXP
ON
Adjust correct perpendicularity of the panel.
Close the frame and fasten the screws A.
Fasten the screws A
•
•
•
•
8
−−−−
sec.3a
2GO! - Technical manual
PANELS
SINTHESI PANEL
Adjust direction of the camera.
Fit the name tags.
ROSSI
ROSSI
Engrave side
White tag
A
•
•
Position the panel on the frame.
Fasten screws B on screws A.
B
A
B
A
B
A
A
•
•
SINTHESI PANEL
INSTALLATION
PANELS
sec.3a
−−−−
9
2GO! - Technical manual
FLUSH-MOUNTED VERSION
45 mm
370 mm244 mm118 mm45 mm
H1
204 / 294 / 384 mm
H1
204 / 294 / 384 mm
H1
204 / 294 / 384 mm
H2
209/ 299/ 389 mm
H2
209/ 299/ 389 mm
H2
209/ 299/ 389 mm
125 mm 250 mm
375 mm
H1= 204, 294, 384 indicates fl ush mounting height and H2=209, 299, 389 indicates to total height relative to 2, 3 and 4 module versions.
WALL-MOUNTED VERSION
416 mm
H3
331 / 421
59 mm
79 mm287 mm
H3
241 / 331 / 421
59 mm
79 mm158 mm
H3
241 / 331 / 421
59 mm
79 mm
H3 referred to the total height may differ according to the number of modules that the case may contain.
§
§
SINTHESI PANEL
DIMENSIONS
SINTHESI PANEL - DIMENSIONS
PANELS
10
−−−−
sec.3a
2GO! - Technical manual
SINTHESI PANEL
VIDEO DOOR PHONE SYSTEM
EXAMPLE OF MODULAR CONSTRUCTIONS WITH VARIOUS CAPACITIES
video door phone system
BUTTONS NUMBER
BUTTONS NUMBER
COMMON
PRODUCTS
FLUSH
MOUNTED (#)
WALL
MOUNTED (#)
GATE
PILLAR (#)
Button and
repertory
modules
Front panel
with 1 button
Flush-mounting
box
Expansion
module
Module
holders
and frames
Wall
cover frame
(°)
Rain hood with
wall cover frame
(°)
Case with hood
frame and
module holders
Case with hood
1145/11
1145/13
1145/12
1145/14
1145/50
Camera
modules
and door unit
1082/72
1038/17
1145/714
1145/52
1145/53
1145/54
1145/62
1145/63
1145/712
1145/713
1145/714
1145/726
1145/728
1145/739
1145/732
1145/612
1145/613
1145/614
1145/626
1145/628
1145/639
1145/632
1145/312
1145/313
1145/314
1145/326
1145/328
1145/339
1145/332
1145/342
1145/343
1234567891011121314151617181920212223242526272829303132
1234567891011121314151617181920212223242526272829303132
1145/64
1145/59
1
111
1
1
1
11
11
11
1
1
11
1111 111
11 221231 2 3 33 44 55445 656 76767
111 1
11
1
111111
1111
11
1
1
111
11
1
1
11
1
1
111 1
11
1
111111
1111
11
1
1
111
11
1
1
11
1
1
111 1
11
1
111111
1111
11
1
1
111
11
1
1
11
1
1
11111 11
1
11111 11
1
11 11111 11 11111 111 1111111111111 11
1
2211 11 11111 222 2222211112
1
111
11
1
1
22
1
2222 2
22
2
22222
3333
33
1
2
22 2111
(°) optional, alternatives
(#) alternatives
1
111
11
1
1
22
1
2222
2
22
2
22222
3
3
33
33
1
2
1
SINTHESI PANEL - VIDEO DOOR PHONE SYSTEM
PANELS
sec.3a
−−−−
11
2GO! - Technical manual
SINTHESI PANEL
VIDEO DOOR PHONE SYSTEM
EXAMPLE OF MODULAR CONSTRUCTIONS WITH VARIOUS CAPACITIES
1324567891011
17
2120 2218 19 23
25 2624 27 28
29 30 31 32
15 16141312
SINTHESI PANEL - VIDEO DOOR PHONE SYSTEM
PANELS
12
−−−−
sec.3a
2GO! - Technical manual
SINTHESI PANEL
DOOR PHONE SYSTEM
EXAMPLE OF MODULAR CONSTRUCTIONS WITH VARIOUS CAPACITIES
door phone system
BUTTONS NUMBER
BUTTONS NUMBER
COMMON
PRODUCTS
FLUSH
MOUNTED (#)
WALL
MOUNTED (#)
GATE
PILLAR (#)
Button and
repertory
modules
Expansion
module
Flush-mounting
box
Door unit
modules
Module
holders
and frames
Wall
cover frame
(°)
Rain hood with
wall cover frame
(°)
(for vertical
panels only)
Case with hood
frame and
module holders
(for vertical
panels only)
Case with hood
1145/11
1145/13
1145/12
1145/14
1145/50
1082/17
1038/17
1145/52
1145/53
1145/54
1145/62
1145/63
1145/712
1145/713
1145/714
1145/726
1145/728
1145/739
1145/612
1145/613
1145/614
1145/626
1145/628
1145/639
1145/312
1145/313
1145/314
1145/326
1145/328
1145/339
1145/342
1145/343
1234567891011121314151617181920212223242526272829303132
1234567891011121314151617181920212223242526272829303132
1145/64
7
8
11111111
1111 111
1
122
1
2312333
44
55445
6
56 76
76
7
11111 11
1
11111 11
1
1
11 11
111
1
111111
1
11 1
11
1
111 1111
11111111
11
1
1
11
1111
1111
1
1
1
1
111
1
1
1
1
11 1
1
12211 11 11111 222 2222211222
1
11
1111
1111
2222 2222
2222222
3333
1
2
22 2111
(°) optional, alternatives
(#) alternatives
111
1
1
1
1
1111
2222
22
22
2222222
33
3
3
1
2
111 1111
11111111
11
1
1
11
1111
1111
1
11
111 1111
11111111
11
1
1
11
1111
1111
1
11
1
1
11
111
1
SINTHESI PANEL - DOOR PHONE SYSTEM
PANELS
sec.3a
−−−−
13
2GO! - Technical manual
SINTHESI PANEL
DOOR PHONE SYSTEM
EXAMPLE OF MODULAR CONSTRUCTIONS WITH VARIOUS CAPACITIES
EXAMPLES OF VERTICAL CONFIGURATIONS
132
4
56
7
8910
11
12 1715 161413
2119 2018 22 23
25 26 27 28
29
24
323130
SINTHESI PANEL - DOOR PHONE SYSTEM
PANELS
14
−−−−
sec.3a
2GO! - Technical manual
SINTHESI PANEL
DOOR PHONE SYSTEM
EXAMPLE OF MODULAR CONSTRUCTIONS WITH VARIOUS CAPACITIES
EXAMPLES OF HORIZONTAL CONFIGURATIONS
1 3 42 5 6
7 8
11
9 10
12
SINTHESI PANEL - DOOR PHONE SYSTEM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

urmet domus MT124-017 Technical Manual

Brand
urmet domus
Model
MT124-017
Category
Door intercom systems
Type
Technical Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents