urmet domus MT124-017 Technical Manual

Brand
urmet domus
Model
MT124-017
Category
Door intercom systems
Type
Technical Manual
sec.3c
−−−−
1
2GO! - Technical manual
CALLING MODULE
PERFORMANCE ..............................................................................2
STRUCTURE ....................................................................................2
DESCRIPTION OF TERMINALS .......................................................2
OPERATION .....................................................................................2
Stand-by .......................................................................................3
Busy .............................................................................................3
Conversation and busy management ..........................................3
Door opener code.........................................................................3
Special code .................................................................................3
Hall button signal management ....................................................4
Auto power-on, surveillance camera management ......................4
Electrical lock ..............................................................................4
PROGRAMMING .............................................................................. 4
Default settings .............................................................................4
INSTALLATION .................................................................................4
Flush-mounted version .................................................................4
Camera module connection .........................................................6
Wall-mounted version with case and hood .................................6
EXAMPLES OF MODULAR CONSTRUCTIONS ..............................7
Download from www.urmetdomus.com Technical Manuals area.
SECTION CONTENTS
Some products may be described in the “New” section.§
SECTION 3C
(REV.D)
CALLING MODULES
Ref. 1082/14K-STEEL CALLING MODULE WITH REPERTORY
2
−−−−
sec.3c
2GO! - Technical manual
K-STEEL CALLING MODULE WITH REPERTORY
Ref. 1082/14
X
7
4
1
0
8
5
2
9
6
3
The Ref. 1082/14 calling module corresponds to 2 K-Steel modules
and is provided with back-lit 16x2 character LCD display, built-in
door unit and back-lit buttons. Flush-mounting boxes or cases with
hood and respective module holders and accessories are required for
installation (see “Installation” section).
PERFORMANCE
The Ref. 1082/14 calling module offers the following functions:
Possibility of managing 2GO! systems with up to 62 users.
Possibility of forwarding door phone or video door phone calls.
Selection of name to be called by means of scroll buttons and
two 16 character row back-lit graphic display. Up to 186 separate
names are available.
Direct selection by keypad of numeric calling code. Up to 62
available user codes. Each user code can be associated to up to 3
different names.
Up to 286 door opener codes split into two categories: 100 generic
codes (not linked to names) and 186 codes associated to names.
Door opener pulse (free or private).
Electrical lock operation tone and visual signal.
60 second pick-up waiting time (system busy).
2 minute maximum conversation time from handset pick-up.
Call and end of conversation confi rmation tones and indication on
display.
Terminals for connecting to hall button for operating the electrical
lock.
Door sensor connection terminals.
Relay box control for cyclic management of several surveillance
cameras.
Speaker volume adjustment trimmer.
Load activation special code management (staircase lights).
Ten interface languages.
Connection to RS485 bus for remote programming via GSM
module.
IrDA infrared interface programming.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
STRUCTURE
X
7
4
1
0
8
5
2
9
6
3
4
1
2
3
5
1
Two-module K-Steel front
2
Infrared port for remote programming
3
Back-lit graphic display
4
Yellow back-lit name selection buttons
5
Green back-lit number pad buttons with yellow back-lit function
buttons: “Cancel”, “Key” and “Call”
DESCRIPTION OF TERMINALS
SE+ Electrical lock terminal (positive)
SE- Electrical lock connection (negative)
GND 2 reference terminals for PA, SP, T terminals
LINE B Terminal pair for connecting non-polarised bus, riser B
LINE A Terminal pair for connecting non-polarised bus, riser A
T 1038/69 relay box connection for surveillance camera cycle
function
V3 Composite video signal
V5 Video signal ground
PA Hall button connection
SP Door open sensor connection
A RS485 half duplex non-reversing input/output
B RS485 half duplex reversing input/output
REF Isolated reference GND potential for RS485 interface
OPERATION
System users are univocally identifi ed by a numeric code from 1 to
62.
A name database can be stored for associating names to numeric
user codes and door opener codes.
Other 100 door opener codes not associated to users can be
managed.
Door opener codes must be univocal in the system.
The various 2GO! repertory operating modes are:
K-STEEL CALLING MODULE WITH REPERTORY Ref. 1082/14
PERFORMANCE - STRUCTURE
DESCRIPTION OF TERMINALS - OPERATION
CALLING MODULES Ref. 1082/14K-STEEL CALLING MODULE WITH REPERTORY
sec.3c
−−−−
3
2GO! - Technical manual
K-STEEL CALLING MODULE WITH REPERTORY Ref. 1082/14
OPERATION
STAND-BY
STAND-BY WITHOUT USER DATABASE
The following appears on the display:
STAND-BY WITH USER CODE DATABASE
The following two messages appear cyclically every two seconds:
BUSY
The following message appears on the display if the module is in
stand-by mode and the line is busy:
CONVERSATION AND BUSY MANAGEMENT
To make a call, either enter the user’s code or select the user’s name
(if a user database is present).
CALL BY ENTERING CODE
The user’s code can be entered using the keypad to make a call. The
following appears on the display:
Press X to correct and return module to stand-by mode.
Press the button after entering the code to make the call. The
button will be activated for 2.5s. Press again to repeat the call.
The following message will appear on the display for two seconds if
the code is wrong (extern to fi rst/last code):
CALL BY SELECTING NAME
A user can be selected if a user name database is present. Press
/ to access the database. The user’s name will appear on two lines,
for example:
Press / to scroll the database in circular fashion (the fi rst user will
appear after the last name). The name list is in alphabetical order.
Press X or wait for the timeout to return to stand-by mode. Press the
button after selecting the name to make the call. The button will be
activated for 2.5s. Press again to repeat the call.
CALL MADE
The following will appear after a call is made:
Conversation will be established with the device if the apartment
station picks up:
A sandglass icon will appear if the video door phone is called
from a door phone station.
DOOR OPENER CODES
The following message will appear if the button
is pressed only
once:
prompting to enter the door opening code. Press X to correct and
return module to stand-by mode. The electrical lock will be operated
and the following message will appear if the entered code is
correct:
The following message appears if the code does not correspond to
a stored code:
Both messages will be shown for three seconds after which the
module will return to stand-by mode.
SPECIAL CODE
A secret four-digit code can be used to send a control to a special
Ref. 1082/80 decoder. Press 0: the following message will appear:
prompting to enter the special code. Press X to correct and return
module to stand-by mode. The following message will appear if
the entered code is correct:
The following message will appear on the other hand if the code is
wrong:
§
CALLING MODULES
Ref. 1082/14K-STEEL CALLING MODULE WITH REPERTORY
4
−−−−
sec.3c
2GO! - Technical manual
K-STEEL CALLING MODULE WITH REPERTORY Ref. 1082/14
PROGRAMMING
INSTALLATION
HALL BUTTON SIGNAL MANAGEMENT
The door unit manages the hall button contact (PA contact). Press the
button (closed contact): the calling module will operate the electrical
lock.
AUTO POWER-ON, SURVEILLANCE CAMERA
MANAGEMENT
Auto power-on is operated on main door unit ID 1. The user will see
the video door unit camera frame when the video door phone auto
power-on button is pressed once. The surveillance camera frames will
be shown in cycle when the button is pressed again. Communication
is established with the video door unit and the respective camera
frame is shown when the user picks up the handset.
The cycle will last for up to the off-hook time (60 seconds) after which
the system returns to stand-by.
ELECTRICAL LOCK
The door unit operates the electrical lock by means of a capacitance
discharge.
The electrical lock is controlled by a pulse (1 second) which can be
managed as follows:
Privacy door opener:
the electrical lock can only be operated by the apartment station
which is communicating with the calling station.
Free door opener:
the electrical lock can be operated also if the apartment station has
not established a communication with the calling station.
The apartment stations which can operate the electrical lock, also
if no communication is established, are those included in the range
from the fi rst code to the last code (see programming).
PROGRAMMING
The calling module with repertory may be programmed as follows:
Locally, via the keypad, without opening the module frame.
Via remote Palm OS device provided with IrDA interface and
appropriate software downloadable from www.urmetdomus.com.
Via Ref. 1082/52 GSM modem and PC software downloadable
from www.urmetdomus.com.
For programming mode refer to the section 2A “Calling module”.
DEFAULT SETTINGS
The default confi guration settings are:
LANGUAGE Italiano
NUMBER OF LINES 2
SURVEILLANCE CAMERAS Off
SPECIAL CODE 1111
PASSWORD 9999
MODULE TYPE Main
DOOR OPENER Privacy
FIRST CODE 1
LAST CODE 62
MODULE ID 1
DOOR PHONE/
VIDEO DOOR PHONE CODE 11 (Video door phone position)
Switch on the device pressing X, 1, 4 and 7 to restore the default
settings.
•
•
•
§
INSTALLATION
The calling module with repertory Ref. 1082/14 can be used alone or
in a combination with a camera unit.
Examples of modular constructions using 2 or 3 module holder frames
with respective fl ush-mounting boxes are shown below.
The door unit module should be installed at a height of approximately
1.55 ÷ 1.60 metres.
h = 1,55 ÷ 1,60 m
X
7
4
1
0
8
5
2
9
6
3
Important
The module should not be illuminated from behind to make the calling
module display easier to read. Never direct the module towards
strong sources of light (e.g. the sun, lampposts, light bulbs, fl ashes
or glare).
FLUSH-MOUNTED VERSION
Purchase fl ush-mounting boxes, frames and module holders
separately for wall mounting. The product codes (according to number
of modules) are:
NUMBER OF
MODULES
FLUSH MOUNTING
BOXES AND MODULE
HOLDERS
FRAME
2 1155/52 1155/85 or 1155/92
3 1155/53 1155/86 or 1155/93
Refer to “Technical product manual - Door phone and video door
phone systems”, “K-Steel panels” section for dimensions and
additional details on these products.
Refer the protections from the hole to be used to pass the wires
only from the fl ush-mounting box.
The holes in the upper part must only be used for introducing the
cables if overlapped to other boxes.
•
§
CALLING MODULES Ref. 1082/14K-STEEL CALLING MODULE WITH REPERTORY
sec.3c
−−−−
5
2GO! - Technical manual
Flush the box and the required height considering the direction and
the indications provided for video systems.
Warning: During installation, protect all parts which will be exposed
to view from mortar, plaster and cement.
NEVER USE ABRASIVE DETERGENTS to clean units.
Fit the fl ush mounting box in line with the wall: it must not project.
max.
6 mm
The wall surface on which the front rests must be as smooth as
possible (max. tolerance 1.5mm).
If the internal production has been removed from the box for any
reason, insert it as shown in the fi gure. Fix it in the upper part not
used for fi xing the module holder frame.
IMPORTANT: the warranty conditions will be forfeited if the
protection is either not installed or installed incorrectly.
For fi tting, loosen the two tap screws and remove the crossbar from
the embedding box frame. Fit the modules in the frame.
n° 7 M3
•
•
§
•
•
K-STEEL CALLING MODULE WITH REPERTORY Ref. 1082/14
INSTALLATION
Fasten the module holder frame to the fl ush mounting boxes by
means of the specifi c hinged attachment.
A
B
C
Fit the seal and close the frame.
n° 4 M4 x 16 mm
X
7
4
1
0
8
5
2
9
6
3
•
•
CALLING MODULES
Ref. 1082/14K-STEEL CALLING MODULE WITH REPERTORY
6
−−−−
sec.3c
2GO! - Technical manual
CAMERA MODULE CONNECTION
A three wire connector is provided for connecting the 1755/40 (colour)
or 1755/70 (black and white) camera module to the back of the calling
module:
RED - Power positive
BLACK - Power negative
WHITE - Video signal coax
For the camera unit specifi cations refer to “Technical product
manual” Door phone and Video door phone systems “K-Steel
panels” section.
WALL-MOUNTED VERSION WITH CASE AND
HOOD
Cases and hoods protect the calling module from the weather and
may be used for installation on walls without fl ush-mounted parts.
The case is provided with module holder frame.
The available models and the dimensions of cases and frames are
shown in “Technical product manual - door phone and video door
phone systems” section “Modular Vandal-proof panel K-Steel”.
1
1,55 m
2
n° 7 M3
3
4
§
Fasten the frame with the three screws provided.
X
7
4
1
0
8
5
2
9
6
3
The tool must only be used manually, and not fi tted on electrical
screwdrivers, to prevent damaging the screws and/or the tool.
90°
OK
NO
•
K-STEEL CALLING MODULE WITH REPERTORY Ref. 1082/14
INSTALLATION
CALLING MODULES Ref. 1082/14K-STEEL CALLING MODULE WITH REPERTORY
sec.3c
−−−−
7
2GO! - Technical manual
EXAMPLES OF MODULAR CONSTRUCTIONS
Reccommended calling module constructions are shown below.
1,55 - 1,60 m
Ref.
1082/14
Ref.
1082/14
Ref. 1155/62
Ref.
1082/14
Ref. 1155/63
Ref.
1755/40 (*)
X
7
4
1
0
8
5
2
9
6
3
Ref.
1082/14
Ref.
1755/40 (*)
X
7
4
1
0
8
5
2
9
6
3
(*) A black/white camera Ref. 1755/70 can be fi tted as an
alternative.
K-STEEL CALLING MODULE WITH REPERTORY Ref. 1082/14
EXAMPLES OF MODULAR CONSTRUCTIONS
5
8
−−−−
sec.3c
2GO! - Technical manual
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

urmet domus MT124-017 Technical Manual

Brand
urmet domus
Model
MT124-017
Category
Door intercom systems
Type
Technical Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents