urban ambiance UQL1391 Installation guide

Type
Installation guide
Package Contents
Warnings and Cautions
1of2
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
A
Inner
Backplate
x1
Pleasegoto forproductcleaningtips.Gotothe selection.
(2)B10CandelabraBaseBulbs60WMaximum,CandelabraBaseT8Vintage Bulbs are recommended, bulbs not included.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
Fixturecanonlybemountedinthedirectionindicatedonpage2.
ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Fixture Body
x1 C
BMounting screw
x4
D
Front/Back
Glass Panel
x2
E
Side Glass
Panel
x2
STEP 1 Install Glass Panels-
A. Remove fixture hood from the top
of the Fixture Body (C) by
unscrewing screws on the side.
B. Install two Side Glass Panels (E)
first. And then install Front/Back
Glass Panels (D). Make sure
smooth surface of Glass Panels
(D/E) are outside during
installation.
C. Insert the bottom edge of the
Glass Panels (D/E) into the slot in
the side of the Fixture Body (C).
Secure the Glass Panels (D/E) by
folding tabs in the top edge of the
Fixture Body (C) onto the top
edge of the Glass Panels (D/E).
Figure 1
D
E
Slot
Tab
C
Screw
Fixture Hood
STEP 2 -Install Bulbs
A. Insert bulbs onto sockets and screw snugly into place.
B. Place the fixture hood back onto the Fixture Body (C) and secure
with previously removed screws. Hand tighten until snug.
Screw
Fixture Hood
C
Socket
T8 Vintage Bulb
(recommended
but not included)
Figure 2
STEP 3 -Install the Inner Backplate to the outlet box
A. Place the supply wires and ground wire through the Inner
Backplate (A). Attach the Inner Backplate (A) to the outlet box with
the head of the green ground screw facing you. Secure it with
outlet box screws (not included). Tighten until snug with
screwdrivers.
Outlet Box
Outlet Box Screw
(not included)
Supply Wires
with Ground Wire
A
Green Ground Screw
Figure 3
Outside Surface is smooth,
Internal Surface is ribbed.
Installation Instructions: UQL1391
www.urbanambiance.com
2of2
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"
STEP 4 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Green Ground Screw
on the Crossbar
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Figure 4
STEP 5 - Install the Fixture Body
A. Place the backplate of the Fixture Body (C) onto the Inner
Backplate (A) and secure with Mounting Screws (B). Tighten until
snug with screwdrivers.
C
A
B
Backplate
Figure 5
STEP 6 -Apply Silicone Sealer
A. Make sure the exterior wall surface and fixture backplate are free of
dirt before applying caulk. Using exterior grade caulk, caulk over top
of backplate and down both sides. Do not caulk the bottom of the
fixture backplate to ensure proper moisture drainage.
Your fixture is now assembled and ready to use. Enjoy!
Exterior
Grade Caulk
Backplate
Figure 6
Exterior
Grade Caulk
8” 6.5”
7.75”
13.25”
17.25”
Fixture can
only be
mounted in
the direction
indicated
7”
FINISH: STAINLESS STEEL
www.urbanambiance.com
UQL1391
  • Page 1 1
  • Page 2 2

urban ambiance UQL1391 Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI