Illumina Direct TST0092C Installation guide

Brand
Illumina Direct
Model
TST0092C
Type
Installation guide
ISSUED 05-2014
PACKAGE CONTENTS
1OF5
STYLE NUMBER: TST0092C
WARNING:
CAUTION:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching
off the circuit breaker or removing the fuse.
● These instructions are provided for your safety. It is very important that they are read completely before the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure that bulb(s) had sufficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
● Do not touch the bulb with bare hands use a cloth or glove.
WARNINGS AND CAUTIONS
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 20 - 30 minutes
● (1) Medium Base 100W Maximum, Alternate (1) CFL bulb.
● : Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape,
safety glasses.
● 1-866-535-1869
● [email protected]
● www.illuminadirect.com
Bulb Recommended:
Tools Required
Phone #:
E-mail:
website:
PREPARATION
www.illuminadirect.com
1-866-535-1869
UM-TST0092C
H
I
J
4pcs
4pcs
4pcs
Lock Screw
Tab
Short Screw
E
1pc
1pc
Fixture Body
Cage
F
G
H
4pcs
Glass Panel
I
J
A
B
D
C
PART
DESCRIPTION
QUANTITY
3pcs
2pcs
Wire Connector
Outlet Box Screw
C
D
E
F
G
A
Crossbar Assembly
(Pre-assembled to fixture body)
1pc
1pc
Green Ground Screw
()Pre-assembled to Crossbar
B
2OF5
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
UM-TST0092C
FINISH: IMPERIAL BRONZE
(1) 100W
Bulb
(Not Supplied)
Medium
Base
10”
9”
12.5”
6.5”
8.5”
4.5”
7”
PART NUMBER REPLACEMENT PART DESCRIPTION
REQ.
NO.
1
G2707PA Glass Panel
4
1
10”
2.5”
Outlet Box Center
2”
3OF5
INSTALLATION INSTRUCTIONS
STYLE NUMBER: UM-TST0092C
STEP 2:
a. Place the Fixture Hood onto the top edge of the Cage.
Line up holes on the top edge of the Cage and Mounting
Holes in the bottom of the Fixture Hood. Using
screwdriver, thread Lock Screws into the Mounting
Holes in the bottom of the Fixture Hood. Hand-tighten
until snug.
Mounting Hole
Lock Screw
Cage with
Glass Panels
Fixture
Hood
Hole
STEP 1:
A. Slip Glass
Panels inside of the Slot in the bottom edge of the
Cage.
b Place Tabs onto the top edge of the Cage and Glass
Panel. Line up holes on Tabs and mounting holes on
the top edge of the Cage. Using screwdriver, thread
Short Screws into mounting holes on the top edge of
the Cage. Hand-tighten until snug.
Put the smooth side of glass outwards.
.
Glass Panel
Slot
Cage
Tab
Short Screw
4OF5
INSTALLATION INSTRUCTIONS
STYLE NUMBER: UM-TST0092C
STEP 4:
a. Connect the House Ground Wire to the Fixture Ground
Wire.
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (White or Ribbed Side).
c. Connect the House Black (or Red) Wire to the Fixture
Supply Wire (Black or Smooth Side).
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the
Outlet Box.
WHITE OR RIBBED
BLACK (OR RED) WIRE
GROUND WIRE
WHITE OR RIBBED
BLACK OR SMOOTH
GROUND WIRE
FROM HOUSE
FROM HOUSE
FROM HOUSE
FROM FIXTURE
FROM FIXTURE
FROM FIXTURE
Use Wire Connectors to connect the wires.
Mounting
Screw
Backplate
Outlet Box
Mounting Ball
Crossbar
STEP 6:
a. Install the correct bulb from the bottom of the Cage, referring to fixture markings and/or labels for maximum
wattage.
STEP 3:
a
. Remove the Crossbar Assembly from the Backplate on
the Fixture Body as shown in STEP 5.
b. Secure the Crossbar Assembly to the Outlet Box with
Outlet Box Screws.
c. Temporarily attach the backplate to the mounting
screws on the Crossbar, securing with the mounting
balls. If the backplate is not snug against the wall,
remove it from the crossbar and adjust the length of the
mounting screws by unscrewing the hex nuts. Turn the
screws in or out of the crossbar until the correct length
is achieved, then re-attach the backplate. Once the
backplate is secure, remove mounting balls and
backplate as shown in STEP 5.
Outlet Box
Crossbar Assembly
Outlet Box Screw
Mounting Screw
Hex Nut
STEP 5:
a. Carefully tuck all wires into the outlet box and position
the backplate of the Fixture Body over the outlet box.
Align the holes in the backplate of the Fixture Body with
the mounting screws attached to the crossbar. Pass the
fixture over the mounting screws and secure by
threading mounting balls onto end of mounting screws.
Tighten until snug.
5OF5
INSTALLATION INSTRUCTIONS
STYLE NUMBER: UM-TST0092C
EXTERIOR GRADE
CAULK
MOUNTING BALL
STEP 5:
a. Refer to the following information for caulking instructions:
With the OUTDOOR FIXTURE properly installed in accordance with supplied Assembly/installation instructions,
proceed with caulking instructions below.
Note: Be sure EXTERIOR WALL SURFACE and FIXTURE BACKPLATE are free to dirt to caulking. Using
EXTERIOR GRADE CAULK, start on one side of FIXTURE BACKPLATE and follow contour, were the FIXTURE
BACKPLATE meets the EXTERIOR WALL SURFACE upward. Proceed to caulk over top of backplate and down
other side. to ensure proper moisture drainage.DO NOT CAULK BOTTOM OF FIXTURE BACKPLATE
Please note that you are required to apply a small
amount of Silicone sealer to the threaded side of the
MOUNTING BALLS and then install them onto the
MOUNTING SCREWS.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
EXTERIOR GRADE
CAULK
OUTDOOR
FIXTURE BACKPLATE
EXTERIOR WALL SURFACE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Illumina Direct TST0092C Installation guide

Brand
Illumina Direct
Model
TST0092C
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents