Extron electronics DTP2 T 204 User manual

User Guide

DTP2 T 204

DTP Switching Transmitters

Four Input Switcher with

Integrated DTP2 Transmitter

68-3277-01 Rev. A

09 20

Safety Instructions

Safety Instructions • English

WARNING: This symbol, , when used on the product, is intended to

alert the user of the presence of uninsulated dangerous voltage within

the product’s enclosure that may present a risk of electric shock.

ATTENTION: This symbol, , when used on the product, is intended

to alert the user of important operating and maintenance (servicing)

instructions in the literature provided with the equipment.

For information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics, see the Extron Safety and

Regulatory Compliance Guide, part number 68-290-01, on the Extron website,

www.extron.com.

Sicherheitsanweisungen • Deutsch

WARUNG: Dieses Symbol auf demProdukt soll den Benutzer darauf

aufmerksam machen, dass im Inneren des Gehäuses dieses Produktes

gefährliche Spannungen herrschen, die nicht isoliert sind und die einen

elektrischen Schlag verursachen können.

VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in

der im Lieferumfang enthaltenen Dokumentation besonders wichtige

Hinweise zur Bedienung und Wartung (Instandhaltung) geben.

Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,

EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in den

Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer

68-290-01) auf der Extron-Website, www.extron.com.

Instrucciones de seguridad • Español

ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto, avisa

al usuario de la presencia de voltaje peligroso sin aislar dentro del

producto, lo que puede representar un riesgo de descarga eléctrica.

ATENCIÓN: Este símbolo, , cuando se utiliza en el producto,

avisa al usuario de la presencia de importantes instrucciones de

uso y mantenimiento estas estan incluidas en la documentación

proporcionada con el equipo.

Para obtener información sobre directrices de seguridad, cumplimiento

de normativas, compatibilidad electromagnética, accesibilidad y temas

relacionados, consulte la Guía de cumplimiento de normativas y seguridad de

Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.

Instructions de sécurité • Français

AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le

produit, signale à l’utilisateur la présence à l’intérieur du boîtier du

produit d’une tension électrique dangereuse susceptible de provoquer

un choc électrique.

ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,

signale à l’utilisateur des instructions d’utilisation ou de maintenance

importantes qui se trouvent dans la documentation fournie avec

l’équipement.

Pour en savoir plus sur les règles de sécurité, la conformité à la réglementation,

la compatibilité EMI/EMF, l’accessibilité, et autres sujets connexes, lisez les

informations de sécurité et de conformité Extron, réf. 68-290-01, sur le site

Extron, www.extron.com.



Copyright

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks (

®

), registered service marks (

SM

), and trademarks (

TM

) are the property of RGBSystems, Inc. or Extron (see the

current list of trademarks on the Terms of Use page at www.extron.com):

Registered Trademarks

(

®

)

Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, eLink, Flat Field, FlexOS, Glitch Free, Global

Configurator, GlobalScripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, MediaPort,

NAV, NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, ShareLink, Show Me, SoundField, SpeedMount, SpeedSwitch, StudioStation,

SystemINTEGRATOR, TeamWork, TouchLink, V-Lock, VideoLounge, VN-Matrix, VoiceLift, WallVault, WindoWall, XPA, XTP, XTPSystems, and ZipClip

Registered Service Mark

(SM)

: S3 Service Support Solutions

Trademarks

(

™

)

AAP, AFL (Accu-RATEFrameLock), ADSP(Advanced Digital Sync Processing), Auto-Image, AVEdge, CableCover, CDRS(ClassD Ripple

Suppression), Codec Connect, DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator, DSPConfigurator,

DSVP(Digital Sync Validation Processing), EQIP, Everlast, FastBite, Flex55, FOX, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, Opti-Torque,

PendantConnect, ProDSP, QS-FPC(QuickSwitch Front Panel Controller), RoomAgent, Scope-Trigger, SIS, SimpleInstructionSet, Skew-Free,

SpeedNav, Triple-Action Switching, True4K, True8K, Vector™ 4K, WebShare, XTRA, and ZipCaddy

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause interference. This interference must be corrected at the expense of the user.

ATTENTION:

• The Twisted Pair Extension technology works with unshielded twisted pair (UTP)

or shielded twisted pair (STP) cables; but to ensure FCC Class A and CE

compliance, STP cables and STP Connectors are required.

• La technologie extension paires torsadées fonctionne avec les câbles paires

torsadées blindées(UTP) ou non blindées(STP). Afin de s’assurer de la

compatibilité entre FCC ClasseA et CE, les câbles STP et les connecteurs STP

sont nécessaires.

NOTES:

• This unit was tested with shielded I/O cables on the peripheral devices. Shielded

cables must be used to ensure compliance with FCC emissions limits.

• For more information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics, see the Extron Safety and

Regulatory Compliance Guide on the Extron website.

VCCI-A Notice

この装置は、クラスＡ情報技術装置です。この装置を家庭環境で使用すると、電波妨害を引き

起こすことがあります。その場合には使用者が適切な対策を講ずるよう要求されることがあります。

ＶＣＣI－Ａ

Conventions Used in this Guide

Notifications

The following notifications are used in this guide:

WARNING: Potential risk of severe injury or death.

AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.

CAUTION: Risk of minor personal injury.

ATTENTION : Risque de blessuremineure.

ATTENTION:

• Risk of property damage.

• Risque de dommages matériels.

NOTE: A note draws attention to important information.

Software Commands

Commands are written in the fonts shown here:

^AR Merge Scene,,0p1 scene 1,1 ^B 51 ^W^C.0

[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]

E X! *X1&* X2)* X2#* X2! CE}

NOTE: For commands and examples of computer or device responses used in this

guide, the character “0” is the number zero and “O” is the capital letter “o.”

Computer responses and directory paths that do not have variables are written in the font

shown here:

Reply from 208.132.180.48: bytes=32 times=2ms TTL=32

C:\Program Files\Extron

Variables are written in slanted form as shown here:

ping xxx.xxx.xxx.xxx —t

SOH R Data STX Command ETB ETX

Selectable items, such as menu names, menu options, buttons, tabs, and field names are

written in the font shown here:

From the File menu, select New.

Click the OK button.

Specifications Availability

Product specifications are available on the Extron website, www.extron.com.

Extron Glossary of Terms

A glossary of terms is available at http://www.extron.com/technology/glossary.aspx.

viiDTP2 T 204 Switcher • Contents

Contents

Introduction ................................................1

About this Guide .................................................. 1

About the DTP2 T 204 Switcher .......................... 1

Features .............................................................. 1

Application Diagrams ........................................... 4

Installation .................................................. 5

Installation Overview ............................................ 5

Rear Panel Features ............................................ 6

Wiring the Power Connector .............................. 11

Wiring for RS-232 Control ................................. 12

Wiring the Contact/Tally Connectors .................. 13

Connecting Using a Show Me (SM Series)

Cable ............................................................ 14

Wiring for Over TP RS-232 and IR Control ......... 14

LockIt HDMI Lacing Bracket Installation ............. 16

Operation..................................................17

Front Panel Features .......................................... 17

Operations......................................................... 18

Powering on the Switcher .............................. 18

Selecting an Input .......................................... 19

Auto-input Switching ..................................... 19

EDID Minder .................................................. 20

Resetting ....................................................... 21

Contact/Tally Modes ...................................... 23

Remote Conﬁguration and Control .............24

Using Simple Instruction Set (SIS) Commands ... 24

Host-to-switcher Communications ................ 24

Switcher-initiated Messages .......................... 24

Error Responses ............................................ 25

Using the Command and Response Table ..... 26

Symbol Deﬁnitions ......................................... 26

Command and Response Table for SIS

Commands ...................................................... 31

Command and Response Table for CEC

Communications SIS Commands ..................... 43

Downloading the DTP2 T 204 Firmware ............ 45

Accessing the Product Conﬁguration

Software ........................................................... 47

Downloading and Installing PCS .................... 47

Starting PCS .................................................. 50

Internal Web Page ..................................... 51

Accessing the Web Page ................................... 51

Web Page Overview .......................................... 52

Communication Settings Panel ...................... 52

Input Status Panel ......................................... 53

Output Status Panel ...................................... 53

Date/Time Settings Panel .............................. 54

Device Info Panel ........................................... 55

Passwords Panel ........................................... 56

Conﬁgure This Device Panel .......................... 57

Mounting ..................................................58

Tabletop Use ..................................................... 58

Rack Mounting .................................................. 58

UL Rack Mounting Guidelines ........................ 58

Furniture Mounting ............................................ 58

DTP2 T 204 Switcher • Contents viii

DTP2 T 204 Switcher • Introduction 1

Introduction

This section gives an overview of the Extron DTP2 T 204 switcher. Topics include:

• About this Guide

• About the DTP2 T 204 Switcher

• Features

• Application Diagrams

About this Guide

This guide describes the DTP2 T 204 switchers and discusses how to install, configure, and

operate them.

In this guide, the terms “DTP2 T 204” and “switcher” are used interchangeably to refer to

the DTP2 T 204 switcher.

About the DTP2 T 204 Switcher

The Extron DTP2 T 204 is a four-input switcher for sending HDMI and control up to 330 feet

(100 meters) over a shielded CATx cable to an Extron DTP-enabled product. It has four

HDMI inputs and a DTP2 output. The DTP2 T 204 supports video signals at resolutions up

to 4K @ 60 Hz at 4:4:4 chroma sampling and complies with HDCP 2.3. Ethernet remote

control and contact/tally connections facilitate integration in professional environments.

Integrator-friendly features include EDID Minder, auto-switching between inputs, and

bidirectional RS-232 and IR pass-through for remote AV device control. The half-rack

enclosure enables discreet placement within lecterns, beneath tables, or wherever needed

to meet application requirements.

The DTP2 T 204 provides reliable switching and transmission of HDMI video at data rates

up to 18 Gbps, along with support for HDR, Deep Color up to 12-bit, 3D, and embedded

HD lossless audio formats. For simplified operation, it can be configured to automatically

switch between the sources. The DTP2 output can be configured to send video and

embedded audio, plus bidirectional RS-232 and IR signals, to an HDBaseT-enabled display.

Features

• Transmits HDMI and control up to 330 feet (100 meters) over a shielded CATx

cable

• Inputs — Four HDMI female type-A connectors

• Output — One DTP2 twisted pair output on RJ-45

• Supports computer and video resolutions up to 4K @ 60 Hz at 4:4:4 chroma

sampling — Support of 4K @ 60 Hz at 4:4:4 chroma sampling requires connection to

a matching DTP2 product.

• Auto-switching between inputs — Multiple switching priority modes are available,

including last-connected input and user-selectable priority.

DTP2 T 204 Switcher • Introduction 2

• Supports HDMI 2.0b specification features include data rates up to 18 Gbps,

HDR, Deep Color up to 12-bit, 3D, and HD lossless audio formats

• Support for High Dynamic Range (HDR) video — Enables greater contrast range

and wider color gamut by providing the necessary video bandwidth, color depth, and

metadata interchange capability for HDR video.

• HDCP 2.3 compliant — Ensures display of content-protected 4K video media and

interoperability with other HDCP compliant devices.

• Remote power capability — Can be remotely powered by a DTP2-enabled product

over the twisted pair connection. Can also be configured to provide power to the

connected DTP2 receiver product.

• Ethernet monitoring and control — Enables control and proactive monitoring over a

network.

• Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for

optimal performance

• Compatible with CATx shielded twisted pair cable — Fully supports a maximum

transmission distance of 330 feet (100 meters) for all compatible resolutions when used

with CATx shielded twisted pair cable. Shielded twisted pair cabling with solid center

conductor sizes of 24 AWG or better is recommended for optimal performance.

• DTP2 output is compatible with HDBaseT-enabled devices — The DTP2 output

can be configured to send video and embedded audio, plus bidirectional RS-232 and IR

signals to an HDBaseT-enabled display.

• Bidirectional RS-232 and IR pass-through for AV device control — Bidirectional

RS-232 control and IR signals can be transmitted alongside the video signal, allowing

remote AV devices to be controlled without the need for additional cabling.

• RS-232 insertion from the Ethernet control port — Saves system resources and

simplifies installation by enabling a control processor to access remote RS-232 devices

over Ethernet.

• CEC insertion — A control processor can insert CEC commands via SIS commands

to control devices connected at the HDMI output.

• Supports multiple embedded audio formats — Compatible with a broad range of

multi-channel audio signals, providing reliable operation with HDMI sources.

• Compatible with all DTP receivers and DTP-enabled products — Enables mixing

and matching with desktop and wallplate receivers, as well as other DTP-enabled

products to meet application requirements.

• User-selectable HDCP authorization — Allows individual inputs to appear

HDCP-compliant or non-HDCP compliant to the connected source, which is beneficial

if the source automatically encrypts all content when connected to an HDCP-compliant

device. Protected material is not passed in non-HDCP mode.

• Comprehensive EDID management — Use PCS to access EDID Minder for setting

video input EDID, capturing EDID from connected displays, or uploading custom EDID

files. Proper EDID management ensures that sources and displays are easily integrated

into a system resulting in optimized system operation. Free, downloadable EDID

Manager 2.0 software is available for advanced EDID editing and creating custom EDID

files.

• EDID Minder automatically manages EDID communication between connected

devices — Ensures that all sources power up properly and reliably output content for

display.

DTP2 T 204 Switcher • Introduction 3

• Key Minder continuously verifies HDCP compliance — Key Minder authenticates

and maintains continuous HDCP encryption between input and output devices to

ensure quick and reliable switching in professional AV environments, while enabling

simultaneous distribution of a single source to multiple displays.

• HDCP authentication and signal presence confirmation — Provides real-time

verification of HDCP status for each digital video input and output. This allows for easy

signal and HDCP verification through front panel LEDs, RS-232, USB, or Ethernet,

providing valuable feedback to a system operator or helpdesk support staff.

• HDCP Visual Confirmation — When HDCP-encrypted content is transmitted to

a non-HDCP compliant display, a full screen green signal is sent to the display for

immediate visual confirmation that protected content cannot be viewed on that display.

• HDMI to DVI Interface Format Correction — Automatically enables or disables

embedded audio and InfoFrames, and sets the correct color space for proper

connection to HDMI and DVI displays.

• Automatic color bit depth management — The DTP2 T 204 automatically adjusts

color bit depth based on the display EDID, preventing color compatibility conflicts

between source and displays.

• Output muting control — Enables HDMI output muting at any time.

• Front panel security lockout — Locks all front panel functions. All functions, however,

are available through USB, RS-232, and Ethernet control.

• Built-in web pages — Enables the use of a standard browser for device monitoring

and troubleshooting over an intuitive web interface.

• RS-232 control port — Enables the use of serial commands for integration into a

control system. Extron products use the SIS command protocol, a set of basic ASCII

commands that allow for quick and easy programming.

• Contact closure remote control with tally output — Allows for remote selection of

an input channel, while a tally output provides +5 VDC to light an LED to indicate the

currently selected input. The contact and tally ports can be configured for independent

use when the DTP2 T 204 is connected to an external control processor.

• Compatible with TeamWork SM Series Cables — SM cables provide convenient

connectivity and user input selection and control for TeamWork Collaboration Systems.

See the TeamWork System Builder to create a customized system for your collaboration

environment.

• Front panel USB configuration port — Enables easy configuration without the need

to access the rear panel.

• LED indicators for signal presence, HDCP, power, and link status — Provides

visual indication of system status for real-time feedback and monitoring of key

performance parameters.

• RJ-45 signal and link LED indicators for DTP port — Provides a means for

validating signal flow and operation, allowing quick identification of connectivity issues.

• Easy setup and commissioning with PCS — Enables configuration of multiple

products using a single software application.

• 1U high, half rack width metal enclosure

• Includes LockIt HDMI cable lacing brackets

• External Extron Everlast power supply included — (Replacement part number

70-769-01) Provides worldwide power compatibility with high-demonstrated reliability

and low power consumption. The Extron Everlast Power Supply is covered by a 7-year

parts and labor warranty.

DTP2 T 204 Switcher • Introduction 4

Application Diagrams

The following diagram shows a typical application for a DTP2 T 204.

L

RS-232 IR

Tx Rx Tx RxG

R

POWER

12V

--A MAX

AUDIO

OUTPUTS

OVER DTP2

SIG LINK

DTP2 IN

--AMAX

POWER

12V

SIG LINK

OUT

1 2 3 4

RxTx

RS-232IR

RxTxG

INPUTS

DTP2 T 204

DTP

HDBT

OFF

SEND

POWER

REMOTE

OVER TP2

5

12 34

G

6

C+VTGC+VT

C+VTCTCTCT

RxTx

G

RS-232

LAN

POWER

12V

0.3A MAX

IPL PRO S3

G

Tx Rx RTSCTS

G

Tx Rx RTSCTS

G

Tx Rx RTSCTS

COM 1 COM 2 COM 3

LAN / PoE

SHARE

MODEL 80

FLAT PANEL

LAN

ON OFF MUTE

HDMI

Ethernet

Extron

DTP2 T 204

Transmitter

Extron

IPL Pro S3

IP Link Pro

Control Processo

r

Extron

DTP2 R 211

Receiver

Ethernet

CATx Cable

up to 330' (100 m)

Flat Panel Display

HDMI

RS-232

Extron

CCR 30

Contact Closure Remote

with Three LED Switches

ON/OFF/MUTE Control

Extron

HDMI SM

Show Me Cables

Figure 1. DTP2 T 204 Application Diagram with IPL Pro and DTP2 R 211

POWER

12V

1A MAX

G

Tx Rx RTSCTS

COM 1

G

Tx Rx

COM 2

VCG

VOL

RELAYS

12C

1 2 3 4G

DIGITAL I/O

PWROUT =6W

eBUS

+V +S

-S

G

LAN

IPCP PRO250

IR/S

SG

L

RS-232 IR

Tx Rx Tx RxG

R

POWER

12V

--A MAX

AUDIO

OUTPUTS

OVER DTP2

SIG LINK

DTP2 IN

--AMAX

POWER

12V

SIG LINK

OUT

1 2 3 4

RxTx

RS-232 IR

RxTxG

INPUTS

DTP2 T 204

DTP

HDBT

OFF

SEND

POWER

REMOTE

OVER TP2

5

12 34

G

6

C+VTGC+VT

C+VTCTCTCT

RxTx

G

RS-232

LAN

RESET

A/PoE

+

B

POWER

12V

1.7A MAX

HDMI HDMI

Tx Rx G

RS-232

COM

L

AUDIO

R

OUTPUT

1

CT

2

CT

3

CT

4

CTG+V

CONTACT / TALLY

LAN

INPUT

OUTPUT

WiFi

1234

MODEL 80

FLAT PANEL

Network

Public

Private

PCSHARELINKON/OFF

PRESS PRESS

USB CHARGER

125 VAC. 50-60 Hz 12A MAX

CATx Cable

up to 330' (100 m)

Extron

HDMI

Sh

ow Me Cables

Extron

DTP2 R 211

Receiver

RS-232

HDMI

RS-232

Extron

DTP2 T 204

Switcher

Display

Extron

IPCP Pro 250

Control Processor

PC

Extron

Cable Cubby 500 CCB

Cable Access Enclosure

Facility/Room

Wireless Access Point

Ethernet

Extron

ShareLink Pro 1000

Wireless Collaboration

Gateway

Wireless

Laptop

Tablet

Smartphone

Ethernet Ethernet

Figure 2. DTP2 T 204 Application with ShareLink and IPCP Pro

1

2

DTP2 T 204 Switcher • Installation 5

Installation

This section describes the installation and setup of the DTP2 T 204 switchers. Topics

include:

• Installation Overview

• Rear Panel Features

• Wiring the Power Connector

• Wiring for RS-232 Control

• Wiring the Contact/Tally Connectors

• Wiring for Over TP RS-232 and IR Control

• LockIt HDMI Lacing Bracket Installation

Installation Overview

To install and set up the DTP2 T 204 switcher:

1. Turn off all equipment and disconnect it from the power source.

2. (Optional) Mount the switcher on a rack shelf or furniture (see Mounting starting on

page58).

3. Connect HDMI input sources

to one or more of the DTP2 T 204 input connectors.

NOTE: LockIt cable lacing brackets, one for each HDMI input connector, are

provided with the DTP2 T 204. These brackets can be used to secure the HDMI

cables to the rear panel connectors to reduce stress on the connectors and

prevent signal loss due to loose cable connections. For information on attaching

the LockIt brackets, see LockIt HDMI Lacing Bracket Installation on

page16).

4. Connect a DTP or HDBaseT compatible output device to the DTP/HDBT OUT

connector.

5. Set the TP mode switch to HDBT (up) or DTP (down).

When the output is configured for DTP mode, remote power is available. When the output

is configured for HDBT mode, remote power is disabled and the switcher and receiver each

require its own 12 VDC power supply.

ATTENTION:

• Position this switch BEFORE connecting the appropriate device to the TP

connector. Failure to comply can damage the endpoint.

• Positionnez le sélecteur AVANT de connecter l’appareil approprié au connecteur

TP. Ne pas respecter cette procédure pourrait endommager le point de connexion.

• Do not connect these devices to a computer data or telecommunications network.

• Ne connectez pas cet appareil à un réseau de télécommunications ou de données

informatiques.

DTP2 T 204 Switcher • Installation 6

6. For IR control and bidirectional over TP RS-232, connect a serial RS-232 signal,

a modulated IR signal, or both into the 3.5 mm, 5-pole captive screw connector

(see Wiring for Over TP RS-232 and IR Control on page14).

7. Connect the computer to one of the following DTP2 T 204 ports to configure and

control the switcher via SIS commands or PCS (Config and LAN ports only):

• RS-232 port — 3-pole captive screw connector for serial RS-232 control (see

Wiring for RS-232 Control on page12 for connection procedures)

• Config port — USB mini-B connector for USB control

• LAN port — RJ-45 connector for Ethernet control (see LAN (Ethernet) connector

on page9).

8. Power on the output display.

9. Connect power to the switcher (see Powering on the Switcher on page18).

10. (Optional) Configure the EDID Minder (see EDID Minder on page20).

11. Power on the source devices.

Rear Panel Features

INPUTS

OVER TP

DTP2 T 204

1 2 3 4

LAN

RS-232 IR

Tx Rx GTxRx

LINKSIG

OUT

Tx

TTCCT +VT

C

TG+V

C

TG+V

C

12 34

56

Rx

RS-232

G

2.2A

MAX

POWER

12V

REMOTE

CONT

HDBT

DTP

SEND POWER

OFF

A

B

C

D

E

F

G

H

F

I

A

Power input connector

B

HDMI input connectors

C

DTP2 and HDBT output connector

D

TP mode switch

E

Over TP RS-232 and IR connectors

F

Contact closure input and tally

output ports

G

Remote RS-232 connector

H

LAN (Ethernet) connector

I

Send Power mode switch

Figure 3. DTP2 T 204 Rear Panel

A

Power input connector — Plug the provided external 12 VDC, 3 A power supply into

this 2-pole, 3.5 mm captive screw connector and into an AC power outlet.

B

HDMI input connectors — Connect HDMI video input sources to these female Type A

HDMI connectors.

NOTE: LockIt cable lacing brackets are provided with the DTP2 T 204 units. These

brackets secure the HDMI cables to the rear panel connectors and reduce stress

on the connectors, preventing signal loss due to loose cable connections.

C

DTP2 and HDBT output connector — Connect the input of a DTP2 or HDBaseT

compatible device to this RJ-45 connector. The connector contains two LEDs:

• Signal LED — This green LED lights green the unit is outputting a TMDS clock

signal.

• Link LED — This amber LED blinks to indicate a valid link is established between

the units.

3

DTP2 T 204 Switcher • Installation 7

D

TP mode switch — Set this switch to DTP or HDBT according to the receiving device

connected to the switcher.

ATTENTION:

• Position this switch BEFORE connecting the appropriate device to the DTP

Out connector. Failure to comply can damage the endpoint.

• Positionnez le sélecteur AVANT de connecter l’appareil approprié au

connecteur TP. Ne pas respecter cette procédure pourrait endommager le

point de connexion.

• DTP mode — By default, the output is configured for DTP mode. It supports

remote powering of the DTP receiver, and transmits digital video and audio

and bidirectional IR control. The DTP2T204 transmits signals up to 330feet

(100meters) to any Extron device with a DTP output.

NOTE: If the receiving device is in the Extron DTP2 series or Legacy

DTP series, set this switch to DTP (Down position). The output transmits

HDMI digital video with embedded audio, analog audio, RS-232 and IR,

and remote power up to 330 feet (100 meters) to any Extron device with a

DTP 330 input, or 230 feet (70 meters to devices with a DTP 230 input.

• If the transmitter and receiver are in the Extron DTP2 series, they

can both be powered by one 12 VDC power supply connected to either

unit.

• If the transmitter and receiver are NOT both in the Extron DTP2

series, the transmitter and receiver each requires its own 12 VDC power

supply.

• HDBaseT mode — When the input is configured tor HDBaseT mode, remote

power is disabled. The DTP2T204 transmits digital video, IR control, and

embedded digital audio up to 330feet (100meters) to any third party device with

an HDBaseT output.

NOTE: If the receiving device is HDBaseT enabled receiver, set this

switch to HDBT (Up position). The TP output transmits HDMI digital video

with embedded audio along with RS-232 and IR control up to 330 feet

(100 meters) to any device with an HDBaseT input. The transmitter and

receiver each requires its own 12VDC power supply.

E

Over TP RS-232 and IR connectors — (Optional) Connect a serial RS-232 signal, a

modulated IR signal, or both to this shared 3.5 mm, 5-pole captive screw connector for

bidirectional RS-232 and IR communication (see Wiring for Over TP RS-232 and IR

Control on page14 to wire this connector).

DTP2 T 204 Switcher • Installation 8

F

Contact closure input and tally output ports — (Optional) To enable control via

contact closure, wire a push-button contact closure device to a C (contact) pin of one of

the contact/tally connectors and to a G (ground) pin. To identify the currently selected

input when the front panel buttons are not visible (if desired), connect an indicator

device, such as an LED, to tally output pin T next to the connected Contact pin.

NOTES:

• Contact closure control overrides front panel input selections.

• For contact closure control, auto-switch mode must be off (see Selecting an

Input on page19).

The contact/tally panel (labeled CONT) contains

two rows of contact and tally connectors (see the

image at right):

• Bottom row — Contains:

1

Contact inputs 1 and 2 — One 5-pole

captive screw connector containing two

pairs of pins labeled C (contact) and T

(tally).

The 5-pole connector also contains a +V

pin, which supplies power to optional tally

indicator devices such as LEDs that are

connected to contact inputs.

3

Contact inputs 3 and 4 — One 4-pole captive screw connector with two

more C-T pin pairs.

4

G pin — A ground pin, located on the 3-pole Remote RS-232 connector.

You can connect a contact closure device to this pin and to a C pin of any

contact/tally input.

• Top row — Contains two 4-pole captive screw connectors, each containing a

contact pin, a ground pin, a tally pin, and a +V pin that can be used to power

connected tally indicator devices.

5

Contact input 5

6

Contact input 6

See Wiring the Contact/Tally Connectors on page13 for information on

connecting contact closure and tally indicator devices to the contact/tally ports.

G

Remote RS-232 connector — Use this 3-pole, 3.5 mm captive screw connector for

RS-232 communication with the switcher (including firmware updates).

To enable RS-232 control, connect the Tx (transmit), Rx (receive) and G (ground) pins

to the serial port of your computer or control system (see Wiring for RS-232 Control

on page12).

CONT

5

12 34

G

6

C+

VTGC+VT

C+VTCTCTCT

RxTx

G

RS-232

22

4

5

5 6

6

3

1

REMOTE

OFF

SEND

POWER

DTP2 T 204 Switcher • Installation 9

H

LAN (Ethernet) connector — Use an RJ-45 cable to connect this jack to a LAN for

control of the switcher via Ethernet.

ATTENTION:

• Do not connect this device to a telecommunications network.

• Ne connectez pas cet appareil à un réseau de télécommunications.

• Use a straight-through cable for connection to a switch, hub, or router.

• Use a crossover cable or a straight-through cable for connection directly to a PC.

Wire the connector as shown in figure 4.

RJ-45

Connector

Insert Twisted

Pair Wires

Pins:

12345678

Straight-through Cable

(for connection to a switch, hub, or router)

End 1 End 2

Pin Wire Color Pin Wire Color

1 white-orange 1 white-orange

2 orange 2 orange

3 white-green 3 white-green

4 blue 4 blue

5 white-blue 5 white-blue

6 green 6 green

7 white-brown 7 white-brown

8 brown 8 brown

Crossover Cable

(for direct connection to a PC)

End 1 End 2

Pin Wire Color Pin Wire Color

1 white-orange 1 white-green

2 orange 2 green

3 white-green 3 white-orange

4 blue 4 blue

5 white-blue 5 white-blue

6 green 6 orange

7 white-brown 7 white-brown

8 brown 8 brown

T568B T568AT568BTIA/EIA-T568B

Figure 4. Wiring for Ethernet Control

I

Send Power mode switch — In a DTP2 transmitter to DTP2 receiver configuration,

set this toggle switch to the Up (Send Power) position on the powered DTP2 unit to

enable sending remote power to the far end. Set the toggle switch to the Down (Off)

position on the DTP2 unit receiving power.

ATTENTION:

• The DTP2T 204 is configured to output power to DTP2 models only. If

connected to a non-DTP2 device, set the SEND POWER toggle switch

to the Off (Down) position. Failure to turn the power OFF will damage the

connected non-DTP2 device (see figure5 on the next page).

• Le DTP2T 204 est conﬁguré pour fournir une alimentation aux modèles

DTP2 uniquement. S’il est connecté à un autre appareil, veuillez positionner

l’interrupteur à bascule sur « Off » (Down). Si l’interrupteur n’est pas positionné

sur Off, vous risquez d’entraîner la défaillance de l’appareil non DTP2 connecté

(voir figure5).

NOTES:

• When the output is conﬁgured for DTP mode, remote power is available only

if both the transmitter and the receiver are from the DTP2 series.

• When the output is conﬁgured for HDBT mode, remote power is not available

and both the transmitter and receiver require their own 12 VDC power supply.

4

DTP2 T 204 Switcher • Installation 10

Figure 5 shows examples of connections for Send Power switch settings.

DTP2 R 211

CONFIG

INPUT

LINK

OUTPUT

SEND

POWER

OFF

STATUS

SEND

POWER

OFF

SEND POWER

OFF

DTP2 R 211

CONFIG

INPUT

LINK

OUTPUT

SEND

POWER

OFF

STATUS

SEND

POWER

OFF

SEND POWER

OFF

SEND POWER

OFF

DTP HDMI 330 Rx

OVER DTP

RS-232

IR

Tx Rx Tx RxG

OFF

ON

ON OFF

INPUTS

OVER TP

DTP2 T 204

12 34

LAN

RS-232IR

Tx Rx GTxRx

LINKSIG

OUT

Tx

TTCCT+VT

C

TG+V

C

TG+V

C

12 34

56

Rx

RS-232

G

2.0A

MAX

POWER

12V

REMOTE

CONT

HDBT

DTP

SEND POWER

OFF

INPUTS

OVER TP

DTP2 T 204

12 34

LAN

RS-232 IR

Tx Rx GTxRx

LINKSIG

OUT

Tx

TTCCT+VT

C

TG+V

C

TG+V

C

12 34

56

Rx

RS-232

G

2.0A

MAX

POWER

12V

REMOTE

CONT

HDBT

DTP

SEND POWER

OFF

INPUTS

OVER TP

DTP2 T 204

12 34

LAN

RS-232 IR

Tx Rx GTxRx

LINKSIG

OUT

Tx

TTCCT+VT

C

TG+V

C

TG+V

C

12 34

56

Rx

RS-232

G

2.0A

MAX

POWER

12V

REMOTE

CONT

HDBT

DTP

SEND POWER

OFF

Local

Power Supply

CATx Cable

up to 330' (100 m)

Local

Power Supply

No Remote Power

Extron

DTP2 T 204

Transmitter

Extron

DTP HDMI 4K 330 Rx

Receiver

DTP Endpoint Connected to a DTP2 Endpoint

CATx Cable

up to 330' (100 m)

Direction of

Remote Power

Local

Power Supply

Extron

DTP2 T 204

Transmitter

Extron

DTP2 R 211

Receiver

CATx Cable

up to 330' (100 m)

Direction of

Remote Power

Extron

DTP2 T 204

Transmitter

Extron

DTP2 R 211

Receiver

DTP2 Endpoint Connected to a DTP2 Endpoint

Local

Power Supply

Figure 5. Send Power Toggle Switch Configuration

5

DTP2 T 204 Switcher • Installation 11

Wiring the Power Connector

A 12 VDC, 3 A, pre-wired power supply is provided with the DTP2 T 204. If, instead, you

intend to use a different power supply, follow the instructions on page12 to wire the

provided 2-pole captive screw connector to your power supply.

ATTENTION:

• The wires must be kept separate while the power supply is plugged in. Remove

power before wiring.

• Les deux cordons d’alimentation doivent être tenus à l’écart l’un de l’autre quand

l’alimentation est branchée. Couper l’alimentation avant de faire l’installation

électrique.

• Always use a power supply supplied and or speciﬁed by Extron. Use of an

unauthorized power supply voids all regulatory compliance certiﬁcation and may

cause damage to the supply and the end product.

• Utilisez toujours une source d’alimentation fournie ou recommandée par Extron.

L’utilisation d’une source d’alimentation non autorisée annule toute conformité

réglementaire et peut endommager la source d’alimentation ainsi que le produit

ﬁnal.

• If not provided with a power supply, this product is intended to be supplied by a

power source marked “Class 2” or “LPS” and rated at 12 VDC and a minimum of

1.5 A.

• Si ce produit ne dispose pas de sa propre source d’alimentation électrique, il doit

être alimenté par une source d’alimentation de classe 2 ou LPS et paramétré à

12 V et 1.5 A minimum.

• The installation must always be in accordance with the applicable provisions of

National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical

Code part 1, section 16. The power supply shall not be permanently ﬁxed to

building structure or similar structure.

• Cette installation doit toujours être en accord avec les mesures qui s’applique

au National Electrical Code ANSI/NFPA70, article725, et au Canadian Electrical

Code, partie1, section16. La source d’alimentation ne devra pas être ﬁxée de

façon permanente à une structure de bâtiment ou à une structure similaire.

• Power supply voltage polarity is critical. Incorrect voltage polarity can damage the

power supply and the unit. The ridges on the side of the cord identify the power

cord negative lead (see ﬁgure6 on page 12).

• La polarité de la source d’alimentation est primordiale. Une polarité incorrecte

pourrait endommager la source d’alimentation et l’unité. Les stries sur le côté

du cordon permettent de repérer le pôle négatif du cordon d’alimentation (voir

ﬁgure6 à la page 12).

• To verify the polarity before connection, plug in the power supply with no load and

check the output with a voltmeter.

• Pour vériﬁer la polarité avant la connexion, brancher l’alimentation hors charge et

mesurer sa sortie avec un voltmètre.

DTP2 T 204 Switcher • Installation 12

ATTENTION:

• The wires must be kept separate while the power supply is plugged in. Remove

power before wiring.

• Les deux cordons d’alimentation doivent être tenus à l’écart l’un de l’autre quand

l’alimentation est branchée. Couper l’alimentation avant de faire l’installation

électrique.

• The length of the exposed (stripped) copper wires is important.

The ideal length is 3/16 inch (5 mm). Longer bare wires can short together.

Shorter wires are not as secure in the connectors and could be pulled out.

• La longueur des câbles exposés est primordiale lorsque l’on entreprend de les

dénuder. La longueur idéale est de 5mm (3/16inches). S’ils sont un peu plus

longs, les câbles exposés pourraient se toucher et provoquer un court circuit. S’ils

sont un peu plus courts, ils pourraient sortir, même s’ils sont attachés par les vis

captives.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in air

handling spaces or in wall cavities.

• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une

utilisation dans les espaces d’aération ou dans les cavités murales.

1. Cut the DC output cord to the length needed.

2. Strip the jacket to expose 3/16 inches (5 mm) of the conductors.

3. Slide the leads into the supplied 2-pole captive screw plug, and use a small screwdriver

to secure them.

4. To verify the power cord polarity before connecting the plug, connect the power supply

with no load and check the output with a voltmeter.

5. Use the supplied tie wrap to strap the power cord to the extended tail of the connector.

SECTION A–A

Ridges

Smooth

A

3/16"

(5 mm) Max.

POWER

12 V

2.2 A MAX

Figure 6. Wiring the Power Connector

Wiring for RS-232 Control

Use a female 9-pin D-to-bare wire RS-232 cable or a universal control cable (UC50' or

UC100') to connect your computer or control system to the RS-232 pins of the Remote

connector.

1. Wire the unterminated end of the RS-232 cable to the provided 3-pole captive screw

plug as described below. Connect the transmit, receive, and ground wires of the cable

to the first three pins on the connector, starting at the left:

• Connect the transmit wire to pin 1 which plugs into the Tx (transmit) port.

• Connect the receive wire to pin 2 which plugs into the Rx (receive) port.

• Connect the ground wire to pin 3 which plugs into the G (ground) port.

2. Plug the 3-pole connector into the Remote receptacle on the rear panel of the switcher.

3. Connect the other end of the cable to the computer or control system connector.

Figure7 on page13 shows how to wire this shared connector for RS-232.

6

Page is loading ...

Extron electronics DTP2 T 204 User manual

Extron electronics DTP2 T 204 User manual

Related papers

Other documents