Extron electronic DTP T USW 233 User manual
- Category
- Video switches
- Type
- User manual
This manual is also suitable for
Extron electronic DTP T USW 233 is a switching video transmitter that can extend the selected signal up to 230 feet (70 m). It can switch among an analog video and two digital (HDMI) video inputs and, paired with a compatible receiver. If the selected input is HDMI, the extended video signal is HDCP-compliant. The DTP T USW 233 is ideal for use in a variety of applications, including:
- Home theater systems
- Conference rooms
- Classrooms
- Training facilities
The DTP T USW 233 is easy to install and operate. It comes with a variety of features, including:
- Front panel input selection buttons
Extron electronic DTP T USW 233 is a switching video transmitter that can extend the selected signal up to 230 feet (70 m). It can switch among an analog video and two digital (HDMI) video inputs and, paired with a compatible receiver. If the selected input is HDMI, the extended video signal is HDCP-compliant. The DTP T USW 233 is ideal for use in a variety of applications, including:
- Home theater systems
- Conference rooms
- Classrooms
- Training facilities
The DTP T USW 233 is easy to install and operate. It comes with a variety of features, including:
- Front panel input selection buttons
1
DTP T USW 233 • Setup Guide
This guide provides instructions for an experienced installer to set up and operate the
Extron DTP T USW 233 switching video transmitter. The DTP T USW 233 transmitter switches among
an analog video and two digital (HDMI) video inputs and, paired with a compatible receiver, can
extend the selected signal up to 230 feet (70 m). If the selected input is HDMI, the extended video
signal is HDCP-compliant.
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the transmitter as required.
Step 2 — Making Connections
Inputs
a
Input 1 (RGB) connector — Connect a VGA cable between this port and the VGA output port of the analog video source.
b
Input 2 and 3 (HDMI) connectors — Connect HDMI cables between these ports and the HDMI output ports of the digital video
sources.
NOTE: See the LockIt
®
Lacing Brackets on page 3 of this guide for to securely fasten the HDMI connectors to the transmitter.
c
Audio input — Connect an unbalanced stereo audio source to this 3.5 mm mini stereo jack for an analog audio input.
NOTE: Audio is not embedded in the HDMI signal; it is transmitted simultaneously and is present on all inputs.
Over DTP RS-232 and IR pass-through
d
RS-232 and IR connector — To pass serial or infrared data or control signals on the Over
DTP RJ-45 output, connect the controlling device to the transmitter via the RS-232 and IR
captive screw connector. Connect the device to be controlled to the receiver.
DTP output to receiver
e
DTP RJ-45 connector — Connect the transmitter DTP Out port to the DTP In port on the
receiver. Extron recommends that you terminate both cable ends in accordance with the
following specications, at a minimum:
• TIA/EIA T 568B • CAT 6a, shielded
• 24 AWG, solid conductor
ATTENTION: Do not connect this device to a computer data or telecommunications network.
Signal LED — Lights when the unit is outputting a TMDS clock signal on the DTP output.
Link LED — Lights when a valid link is established between the units on the DTP cable.
Remote control
f
Remote Contact port — If desired, for contact closure control, plug a locally-contructed contact closure control device into this
3.5 mm, 4-pole captive screw port. Momentarily short the pin for the desired input (1, 2, or 3) to G to select that input. To force an
input to be always selected, leave the short in place.
NOTES:
• Contact closure control overrides front panel input selections.
• For contact closure control, auto-input switching mode must be off (see Selecting the switch mode on the next page).
POWER
12V
2
--A MAX
Rx GTx RxTxG
RS-232 IR
RxTx
1
RGB, Y, R-Y, B-Y HDMI HDMI
SIG LINK
DTP OUT
AUDIO
CONTACT RS-232TALLY
3
123G 123+V
RESET
INPUTS
OVER DTPREMOTE
4 6
10 51 2 923
87
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Blue
TIA/EIA T
568B
TP Wires
12345678
Pins:
TxRx
RxTx
Gnd
Gnd
IR Device
RS-232 Device
RxTx RxTxG
RS-232 IR
OVER DTP
2
DTP T USW 233 • Setup Guide (Continued)
g
Remote Tally port — If desired, to remotely identify the currently selected input, plug a locally-constructed device into this 3.5 mm,
4-pole captive screw connector. Connect the power wire for the device into the +V pin and connect the ground wire for the each
indicator into the corresponding tally output pin: 1, 2, or 3.
When an input is selected, by either contact closure or front panel selection, the corresponding tally output pin shorts to ground,
closing the circuit and lighting the connected indicator (LED).
h
Remote RS-232 port — Plug a serial RS-232 device into the switching transmitter via this rear
panel 3.5 mm, 3-pole captive screw connector for remote control of the switching transmitter.
Reset button
i
Reset button — This button initiates two levels of reset. For different reset levels, use an
Extron Tweeker or small screwdriver to press and hold the recessed button while the switcher
is running or while applying power. See the DTP T USW 233 User Guide, available at www.extron.com, for details.
Power
j
Power connector — Connect an IEC power cord between the included 12 VDC
power supply and a 100-240 VAC, 50-60 Hz source. Connect the power supply to
either unit, transmitter or receiver, as shown at right. Use the included tie-wrap to
strap the cord to the captive screw connector.
NOTE: Only one power supply is required. A single power supply connected to
either unit in the pair powers both units. A power supply is included with the
transmitter.
Front panel Configuration port
a
Configuration port — Plug a PC or other controlling device into the switching transmitter via this front
panel mini-USB connector for remote conguration of the switching transmitter.
Operation
Switching inputs
Select the desired input by pressing the associated input button. Observe that the
LED for the selected input lights.
NOTE: The switcher must be in normal (manual) mode (see below).
Selecting the switch mode
In auto-input switching mode, the switcher selects to the highest numbered input
with a sync signal present. Turn auto-input switching mode on and off as follows:
1. Press and hold the Mode (Input 1) button.
2. Press and release the button for the desired mode:
Auto (Input 3) — The Auto Switch LED lights.
Normal (Input 2) — The Auto Switch LED goes off.
3. Release the Mode button.
Locking and unlocking the front panel
(Executive mode)
The switcher has a front panel lock feature that locks the front panel. If you try to make
front panel input selections when the panel is locked, all front panel LEDs ash three
times. Toggle the front panel lock on and off by pushing and holding all three Input
buttons simultaneously for 5 seconds. All front panel LEDs ash three times.
Release the buttons.
Interpreting the Status LEDs
Signal LEDs (1 through 3) —Indicate that the switcher detects horizontal sync
(Signal LED 1) or TMDS clock (Signal LED 2 and Signal LED 3) signals on the associated input.
HDCP LEDs (2 and 3) —Indicate that the corresponding input signal is HDCP encrypted.
Power Supply
Output Cord
Ridges
Smooth
Captive
Screw
Connector
3"
16 (5 mm) Max.
SECTION A–A
AA
REMOTE
RxTx Gnd
RS-232 Device
GRxTx
RS-232
V
AUTO
SWITCH
CONFIG
1
1
23
MODE
NORMAL
AUTO
Press the button.
The LED lights
green.
1 23
MODE
NORMAL
AUTO
AUTO
SWITCH
Press the and HOLD the Mode button.
Press and release the Auto or Normal button.
Release the Mode button.
Auto Switch lights (auto)
or goes out (normal).
1
23
MODE
NORMAL
AUTO
Press the and
HOLD
the all three Input buttons.
All three LEDs flash three times. Release the Input buttons.
HDCP
SIGNAL
STATUS
123
3
3
3
1
2
4
5
LockIt
®
Lacing Brackets
Use the included LockIt Lacing Brackets to securely fasten both HDMI cables as follows.
1. Plug the HDMI cable into the panel connection.
2. Loosen the HDMI connection mounting screw from the panel enough to allow the LockIt lacing
bracket to be placed over it. The screw does not have to be removed.
3. Place the LockIt lacing bracket on the screw and against the HDMI connector, then tighten the
screw to secure the bracket.
ATTENTION: Do not overtighten the HDMI connector mounting screw. The shield it fastens
to is very thin and can easily be stripped.
4. Loosely place the included tie wrap around the HDMI connector and the LockIt lacing bracket as
shown.
5. While holding the connector securely against the lacing bracket, use pliers or similar tools to
tighten the tie wrap, then remove any excess length.
Application Diagram
POWER
12V
2
--A MAX
Rx GTx RxTxG
RS-232 IR
Rx
T
x
1
RGB, Y, R-Y, B-Y HDMI HDMI
SIG LINK
DTP OUT
AUDIO
CONTACT RS-232TALLY
3
1 2 3 G 1 2 3 +V
RESET
INPUTS
OVER DTP REMOTE
Tx Rx G Tx Rx
RS-232
IR
OVER DTP
OUTPUTS
AUDIO
1
31
42
3
1
4
2
3
1
4
2
2
3
100
L
INK
ACT
CO
M
IR
I
NPUT
R
EL
AY
T
X RX
R
IPL 250
®
ON
OFF
D
I
S
PLAY
M
U
T
E
SC
REE
N
U
P
S
CRE
E
N
D
OW
N
VCR
D
VD
DOC
CAM
LAP
TOP
PC
Extr
on
DTP T
USW 233
DT
P Transmitter
La
ptop
Laptop
Document
Camera
TCP/IP
AV Device
Control
Switcher
Control
VGA
HDMI
HDMI
Extron
TouchLink
Control
System
Extron
IPL 250
CATx Cable
Up to 230' (70 m)
Extron
DTP HDMI 230 D Rx
Receiver
HDMI with
Embedded
Audio
Flat Panel Displa
y
with Speakers
AV Device
Control
Figure 1. Typical Switching Transmitter Application
4
68-2490-50 Rev. A
11 13
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2013 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
-
1
-
2
-
3
-
4
Extron electronic DTP T USW 233 User manual
- Category
- Video switches
- Type
- User manual
- This manual is also suitable for
Extron electronic DTP T USW 233 is a switching video transmitter that can extend the selected signal up to 230 feet (70 m). It can switch among an analog video and two digital (HDMI) video inputs and, paired with a compatible receiver. If the selected input is HDMI, the extended video signal is HDCP-compliant. The DTP T USW 233 is ideal for use in a variety of applications, including:
- Home theater systems
- Conference rooms
- Classrooms
- Training facilities
The DTP T USW 233 is easy to install and operate. It comes with a variety of features, including:
- Front panel input selection buttons
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Extron electronics DTP T MK 332 User manual
-
Extron DTP HDMI 4K 330 Rx User manual
-
Extron electronics XTP SR HDMI User manual
-
Extron electronics XTP T UWP 202 User manual
-
Extron electronic IN1608 User manual
-
Extron electronics 1600 User manual
-
-
Extron SW HDMI Series User manual
-
Extron electronics CTR 8 User manual
-
Other documents
-
Legrand 40744 Owner's manual
-
-
-
Extron electronics DTP2 T 212 User manual
-
Extron electronics DTP T MK 232 User manual
-
Extron electronics DTP T USW 233 User manual
-
Extron electronics DTP T SW4 HD 4K User manual
-
-
Extron electronics DTP2 T 212 User manual
-
Extron DTP T SW4 HD 4K User manual
