SDU-Lon Installation Instructions TG200599 Issue 1/C 20/11/06
1
Installation Instructions
SDU-Lon
Smart Display Unit
Important: Retain these instructions
3 Installation
1 Unpacking
SDU-LON Installation
Instructions TG200599
H O
2
-10 °C
+14 °F
+50 °C
+122 °F
0 %RH
95 %RH
2 Storing
It is recommended that the installation should
comply with the HSE Memorandum of Guidance
on Electricity at Work Regulations 1989.
For USA install equipment in accordance with
the National Electric Code.
WARNING: Other than removing
front panel (step 3), do not open unit.
DANGER high voltage. No
serviceable parts inside.
Note that this product may involve Lonworks system integration as referred to in step 12:
this procedure should only be performed by an installer with LonWorks engineering
expertise.
!
Dimensions
1
90 mm (3.54”)
25 mm
(0.98”)
30 mm (1.18”)
90 mm (3.54”)
150 mm (6”) 150 mm (6”)
SDU-Lon Installation Instructions
SDU-Lon Installation Instructions TG200599 Issue 1/C 20/11/06
2
3 Installation (Continued)
Requirements (continued)
2
b
c
H O
2
-10 °C
+14 °F
+40 °C
+104 °F
0 %RH 90 %RH
a
Remove Front Panel
3
Route Cables
5
b
a
c
Check SDU type
4
Check SDU-LON
* If one side of the 24 Vac input power is connected
to 0 V, that side must be connected to the SDU
- (negative) terminal
+
+
+24 Vdc
24 Vdc Power
Supply
SDU
0 Vdc
+
+24 Vac (L)
24 Vac Power
Supply
SDU
+24 Vac (N)
24 Vdc
15 mA
24 Vac
15 mA
*
O
I
S P E N G
1 2 3 4
SDU
Configure SDU
6
to change operating mode, restrictive set, or language
a Connect Input Power
b Switch on Power
24 V
Power
Supply
SDU-Lon Installation Instructions TG200599 Issue 1/C 20/11/06
3
Installation Instructions SDU-Lon
+
24 V
Power
Supply
LCI
RJ11
SDU-LON
supplied with LCI
Cable/EJ101442
9 way D type Female
LonWorks
LonWorks
SET,
SDU Tool
3 Installation (Continued)
Configure SDU (Continued)
6
LCI Installation Instructions
TG200429
c Connect to PC
d Set up SDU Configuration File
SDU Tool
Set up:
Mode Unrestricted/Restricted
Home Page Show/Don’t show
Restrictive mode list Select required modules
Language Translation of standard text
Backup File to Disk
S P E N G
1 2 3 4
SDU Data Sheet TA200559
SDU Tool Manual TE200600
SET
SDU Tool
Select
Language
Download to
SDU
f Download Language
Download Complete
h Set SDU into Download Mode
S P E N G
1 2 3 4
Config Update
i Transfer Completed
S P E N G
1 2 3 4
Config Update
j Switch off Input Power
SP ENG
1234
O
I
24 V
SDU
e Identify SDU to SDU Tool
g Download Completed
SP - service pin
SDU-Lon Installation Instructions
SDU-Lon Installation Instructions TG200599 Issue 1/C 20/11/06
4
I Q L I Q L S D U S D U
L O N
R o u t e r
L O N
R o u t e r
L o n L o n
s e g m e n t
a s s o c i a t e d
a s s o c i a t e d
V i r t u a l
L a n
3 Installation (Continued)
Note that: If two SDU/LONs are associated with IQLs which are on the same Lan, the SDU-LONs
must be on the same segment (i.e. on the same section of LonWorks separated by routers).
If the system is installed on a LonWorks Management Tool (as in step 12), this rule does
not apply.
I Q L I Q L S D U S D U
L O N
R o u t e r
L O N
R o u t e r
L o n L o n
s e g m e n t
a s s o c i a t e d
a s s o c i a t e d
V i r t u a l
L a n
Connect to LonWorks
7
+
Lon
Lon
T e r m i n a t o r
T e r m i n a t o r
T e r m i n a t o r
Star topology Ring
topology
Bus topology
1 0 0
m
F , 5 0 V m i n
1 0 0
m
F , 5 0 V m i n
Do not allow wires
to cross on a loop
* Terminate bus at one end only
Terminator
e.g. LONTERMINATOR
Terminal size 0.5 to 2.55 mm
2
(14 to 20 AWG)
Normal Trend Lan cable is not recommended.
Do not use screened cable.
elbaChtgnelsubxaM
otedonxaM
edon
20158nedleB)sdy545(m005)sdy545(m005
metsysQI
002/FH/61/0/1/PT
)1748nedleB(
)sd
y545(m005)sdy034(m004
GWA22,VIleveLLU)sdy545(m005)sdy034(m004
8.0x2x2Y)tS(YJ)sdy545(m005)sdy053(m023
GWA42,5.
taCA865AIT)sdy094(m054)sdy072(m052
LonA
SCN
LonB LonA
SCN
LonB
LINC
A
IQLROUTER
B
IQL
x
y
A
IQLROUTER
B
z
w
LONC
IQL
x
yz
w
LonA
SCN
LonB LonA
SCN
LonB
LONC
LonA
SCN
LonB LonA
SCN
LonB
45
6
7
89
10
11
T
T
T
45
6
7
89
10
11
SDU
xcite
Maximum 64 nodes per Lon segment
Maximum 40 IQLs (and LONCs) per Lan
Recommend terminate at
LINC or Router.
e.g. use IQLRouter integral
terminators
SDU-Lon Installation Instructions TG200599 Issue 1/C 20/11/06
5
Installation Instructions SDU-Lon
* If one side of the 24 Vac input power is connected to 0 V, that side must be connected to the SDU - (negative)
terminal
Connect Input Power
8
Check Start Up Reset
10
S P E N G
1 2 3 4
T r e n d S D U V 1 . 0
Firmware version
communications failure
or no sensor set up
Connect to IQ
Check LonWorks Connected
11
+
LonWorks (green)
SDU faulty
Switch on Input Power
9
failed to install on Lon;
check step 7
installed on Lon
3 Installation (Continued)
+
+
+24 Vdc
24 Vdc Power
Supply
SDU
0 Vdc
+
+24 Vac (L)
24 Vac Power
Supply
SDU
+24 Vac (N)
24 Vdc
15 mA
24 Vac
15 mA
*
O
I
S P E N G
1 2 3 4
SDU
24 V Power
Supply
SDU-Lon Installation Instructions
SDU-Lon Installation Instructions TG200599 Issue 1/C 20/11/06
6
Mount Unit
14
Standard UK pattress wall box
or panel
60 mm
46 mm
50 mm
Ø 4 mm
(M3.5
screw)
Ø 4 mm
(M3.5
screw)
60 mm
2 off (M3.5 x 35 mm)
screws provided
Install on Lon Management Tool
12
If other IQ System devices on LonWorks are installed on LonWorks Management Tool.
When installing SDU-LON on LonWork Management Tool, push service pin button when requested.
S P E N G
1 2 3 4
See LonWorks network management tool
manual. See IQ System LonWorks Products
Engineering Manual (TE200292). LonWorks
System integrator must have LonWorks
engineering expertise.
SDU Data Sheet TA200559
for LonWorks network
variables (NVs)
The SDU must also be associated with its IQL using the LMT
The following network variables need to be set up using the LMT:
nciInstallState: set to CFG_EXTERNAL
nciHostNodeAddr: set to associated IQL LonWorks node address
nciSubnetAddr: set to associated IQL LonWorks subnet address
nciMsgCode: set message code of associated IQL
nciDomainIndex: set to domain index of associated IQL
service pin button
Associate SDU with its IQL
13
ab
not if installed on LonWorks Management Tool
SP ENG
1234
Conn ect to IQ
“Connect to IQ”
SP ENG
1234
Press IQL Service PIN
“Press IQL
Service Pin”
cd
4 secs
Either use IQLTool2 runing in SET and connected to LonWorks using LCI or use buttons as follows:
3 Installation (Continued)
2 4 V a c
I Q
L
+
O / S
L A N
L O N
N I D
S t r a t e g y
: : : : :
D O 1
I N 1
D O 2
D O 3
~
D O 4
D O 5 I N 2
I N 3
2 4 V
C O M
2 4 V
C O M
~
C O M
service pin button
SDU-Lon Installation Instructions TG200599 Issue 1/C 20/11/06
7
Installation Instructions SDU-Lon
3 Installation (Continued)
Check Display
16
1234
S e n s o r 1
F l o o r 1 S p a c e T e m p
2 0 . 3 D e g C
Displays first labelled
sensor if set to
defaults
Replace Front Panel
15
Check Operation - Monitor
17
1234
Sensor
S e n s o r 1
F l o o r 1 S p a c e T e m p
2 0 . 3 D e g C
Knob
Switch
Driver
Digital Input
Time Zone
Time
1234
S e n s o r 1
F l o o r 1 S p a c e T e m p
2 0 . 3 D e g C
Sensor 1
Sensor 2
Sensor (last)
1234
Calendars
Note that the full sequence listed here
may only be shown in Unrestricted
modes. The Restricted modes show
only those pages on the Restricted
list. The Home page is optional (see
step 6d).
Plant Room 1
20/03/02 08:04
Home page
SDU-Lon Installation Instructions
SDU-Lon Installation Instructions TG200599 Issue 1/C 20/11/06
8
3 Installation (Continued)
1234
1234
Check Operation - Adjust
18
1234
Digital
ON
Analogue
if PIN required
see step 19
OFF
Units
20.32
Tenths
20.32
Knob 1
Room 1 Setpoint
20.01 DegC
Knob 1
Room 1 Setpoint
20.01 DegC
Knob 1
Room 1 Setpoint
20.01 DegC
Hundreths
20.32
SDU-Lon Installation Instructions TG200599 Issue 1/C 20/11/06
9
Installation Instructions SDU-Lon
1234
S e n s o r 1
F l o o r 1 S p a c e T e m p
2 0 . 3 D e g C
Enter PIN
19
a
PIN
5 * * *
b
c
PIN X
5 * *
d
e
PIN X X
5 *
f
g
PIN X X X
5
h
1234
P I N 5 * * * *
If required
3 Installation (Continued)
SDU-Lon Installation Instructions
SDU-Lon Installation Instructions TG200599 Issue 1/C 20/11/06
10
Set SDU Mode
20
If required
S P E N G
1 2 3 4
S e n s o r 1
F l o o r 1 S p a c e T e m p
2 0 . 3 D e g C
Display Mode = 1
S e n s o r 1
F l o o r 1 S p a c e T e m p
2 0 . 3 D e g C
Display Mode = 7
Default - Display Mode 0:
No home page, alarm log disabled
Note that if the home page is enabled, the controller’s identifier [R(D)] should be set up, otherwise
the first line of the home page will show the label of the previous item displayed.
3 Installation (Continued)
a Remove front panel - see step 3
b Set mode
c Replace front panel - see step 15
edoMteSegaP
emoH
egaP
mralA
goL
0detcirtsernUoN
oN
1detcirtsernUseY
oN
2detcirtsernUoN
oN
3detcirtsernUseY
oN
4detcirtseRoN
oN
5detcirtseRseY
oN
6detcirtseRoN
oN
7detcirtseRseY
oN
Note that the alarm log is permanently disabled
for SDU-LON so the SDU mode selects restricted/
unrestricted and home page
Engineering Resets
21
If need temporary Unrestricted mode for commissioning or need Manual reset (e.g. after multiple
mode changes as in step 20)
1234
Hold 5 secs - 10 secs Temporary Unrestricted Mode - returns to
previous mode 20 seconds after last key press.
Hold 10 secs or greater Manual Reset
SDU-Lon Installation Instructions TG200599 Issue 1/C 20/11/06
11
Installation Instructions SDU-Lon
Set up Parameters
22
Set up the following parameters for IQL using SDU:
Knobs
Switches
Time Zone Day of week (1 to 14) Period (1 to 3)
Start hours, minutes Stop hours, minutes
Time hrs, minutes, day of month, month, year
daylight saving on, day of month, month
daylight saving off, day of month, month
Calendars Use (next, Free, every)
Start date Stop date
Special day type for the zone
SDU Data Sheet
TA200559
If required
Note that if a 963 is to centrally control the IQL’s occupation state, then the SDU time zone’s times
should be left nulled at 00:00.
Note that if a 963 is centrally synchronising time, it should do so using a timemaster which will in
turn synchronise the SDU.
3 Installation (Continued)
SDU-Lon Installation Instructions
SDU-Lon Installation Instructions TG200599 Issue 1/C dd/mm/yy
12
Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Ecublens, Route
du Bois 37,Switzerland by its Authorized Representative, Trend Control Systems Limited.
Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof
without obligation to notify any person of such revisions or changes.
Trend Control Systems Limited
P.O. Box 34, Horsham, West Sussex, RH12 2YF, UK. Tel:+44 (0)1403 21888 Fax:+44 (0)1403 241608 www.trend-controls.com
Trend Control Systems USA
6670 185th Avenue NE, Redmond, Washington 98052, USA. Tel: (425)897-3900, Fax: (425)869-8445 www.trend-controls.com
WEEE Directive :
At the end of their useful life the packaging,
and product, should be disposed of by a
suitable recycling centre.
Do not dispose of with normal household waste.
Do not burn.
4 Disposal
/
