CAME AGT Installation guide

Brand: CAME

Model: AGT

Category: Security access control systems

Type: Installation guide

CAME AGT is a single LED intercom internal audio receiver that can be installed at an appropriate height for the user. The device has a door lock release button and two auxiliary buttons. The ringtone volume can be set with key presses to off, low, medium, or maximum volume. The device has terminals for call from entry panel input, audio from entry panel, audio to entry panel, auxiliary services, and power supply. The device can be programmed to connect up to three internal receivers in parallel on the same call.

AGTK200A03KHNA

HPC/1 + HNA

AGT A200K

A/200N

HA/200

AGT A200K + TARGHA + HNA KIT FA01559-EN

INSTALLATION MANUAL

AGT A200K

HA/200 A/200N

HBP HPC/1+HNA

Page 2 - Manual FA01425-EN - 02/2021 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions

CONTENTS OF THE KIT

General precautions

• Read the instructions carefully before staring installation and perform all procedures as explained by the manufacturer.

• The installation, programming, commissioning and maintenance of the product must only be carried out by technicians who are

qualiﬁ ed and properly trained in compliance with the regulations in force, including as regards health and safety, and disposal of

packaging.

• The installer must ensure that the information for the user, where there is any, is provided and delivered.

• Before carrying out any cleaning or maintenance, disconnect the devices from the power supply.

• The equipment must only be used for the purpose for which it was expressly designed.

• The manufacturer declines all liability for any damage as a result of improper, incorrect or unreasonable use.

• Only use soft, dry or slightly damp cloths to clean the device. Do not use any chemical products.

• These instructions must be attached to the device.

This product complies with current applicable reference standards.

DISPOSAL - Dispose of the packaging and the device at the end of its life cycle responsibly, in compliance with the laws in force

in the country in which the product is used. The recyclable components are marked with a symbol and the material ID marker.

THE DATA AND INFORMATION IN THIS MANUAL MAY BE CHANGED AT ANY TIME AND WITHOUT NOTICE. THE MEASUREMENTS,

UNLESS OTHERWISE STATED, ARE IN MILLIMETRES.

SW11

EXT.AUX 1

LED

P. B . SW12

SW11

Page 3 - Manual FA01425-EN - 02/2021 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions

AGT A200K

Description

Intercom internal audio receiver.

Function of terminals and jumpers

Terminal board M1

5Earth

7Call from entry panel input

8Audio FROM entry panel

9Audio TO entry panel

AUX2: auxiliary services (24V 100 mA)

21 +11 to 175 VDC LED power supply

AUX 1 (24V 100mA)

24 AUX1 LED (active to earth with SW12 jumper in position

EXT.)

Function of SW11 jumper

Remove the jumper to make the door lock release button ( )

active only with the handset raised.

Function of SW12 jumper

EXT.: LED connected to terminal 24.

P.B.: LED connected to AUX1 key.

Technical data

Type AGT A200 K

Single LED consumption (mA) 1

Operating temperature (°C) +5 to +40

Storage temperature (°C) -25 to +70

IP Rating IP30

503 503

Ø60

Page 4 - Manual FA01425-EN - 02/2021 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions

Installation

• Open the device by pressing on the tab at the bottom .

• Separate the shell from the bottom of the device.

• Fasten the bottom of the device to the box on the wall

• Avoid overtightening the screws.

the box must be installed at an appropriate height for the

user.

• Once all connections have been made, reattach the shell to

the bottom of the device .

Ringtone settings

O (red LED on)

Where there is no power to terminal 21, the

volume switches from O to Low.

Medium volume

Maximum volume

Button functions

Door lock release

AUX 1

AUX 2

64,5

105

145

43,5

7,5 57

105

106

Page 5 - Manual FA01425-EN - 02/2021 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions

A/200N

Description

A/200N guarantees the power supply to the HPC/1 entry panel

and a maximum of 20 front plates with 6 buttons HPP/6.

It is provided with the following functions:

- 2 dual-tone call beeps for two entry panels (or for additional

call, e.g. from the landing).

- Power supply and control for solenoid lock (12 V AC, 1 A) via

a relay (inside the device) controlled by a timer, adjustable from

2 to 15 seconds using the potentiometer P1 .

- Call generator: 2 types of dual-tone beep (up to 3 internal

receivers can be connected in parallel on the same call). The

device can be powered at 12 V DC, for example by a battery or

UPS (terminals +B and 5).

The equipment does not include a battery protection device.

Function of terminals and jumpers

Terminal board A

Network

Terminal board B

+B Input 12 V DC (*)

5 Earth

21 Output 11 V DC

8 Common call output 1

8A Common call output 2

11 Audio from entry panel

12 Audio to entry panel

23 – Output 14 V AC

16 +

NO Normally open

relay contactsC Common

NC Normally closed

(*) The device is electronically protected against overloads and

short circuits.

Terminal board C

5 Earth

8 Audio to internal receiver

9 Audio to internal receiver

Technical data

Type A/200N

50-60 Hz (VAC) power supply 230

Power consumption (VA) 34

Output voltages at 11 VDC (mA) 150

Output voltages at 14 VAC (mA) 650

Peak output voltages (mA) 300

Operating output voltages (mA) 650 (1A)

Storage temperature (°C) -25 to +70

Operating temperature (°C) 0 to +35

IP Rating IP30

Page 6 - Manual FA01425-EN - 02/2021 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions

HA/200

Trimmers

Speaker audio

Microphone audio

Technical data

Type HA/200

Power supply (VDC) 12

Max power consumption (mA) 50

Power consumption in stand-by (mA) <35

Storage temperature (°C) -25 to +70

Operating temperature (°C) -15 to +50

IP Rating IP54

Installation

• The device can be installed on DIN rails (EN 50022) on a

suitable switchboard, or on the wall using the terminal covers.

• To dismantle the device, proceed as shown in ﬁ gure 2-3.

• See ﬁ gure 1 for dimensions.

The power supply must always be installed horizontally.

Ensure there is correct ventilation if the power supply is

installed in a metal case.

Description

Audio module.

Functions of terminals and audio adjusters

Terminal board

5 – power supply

21 + 12 VDC

8 common call (for call beep)

11 audio to internal receiver

12 audio from internal receiver

14 enable

In systems in which there is an enable command, terminal

14 can be connected to the earth (unit always active) or to

terminal 12 (unit active only when handset is raised).

A B C

HNA/102

Description

Access control module equipped with 2 relays that can be acti-

vated by codes keyed in on keypad.

Function of terminals and link

Terminal board M1

12÷16 VAC, 14÷18 VDC Power supply input

I1 En-

trance Entry panel contact

–Ground

Terminal board M2

C1 Common

Relay contact 1NC Normally closed contact

NO Normally open contact

C2 Common

Relay contact 2NC Normally closed contact

NO Normally open contact

Function of SW1 link

Armed: Button illumination on.

Disarmed: Button illumination NOT on (default).

Technical data

Type HNA/102

Power supply (VAC) 12÷16

Consumption with AC power supply (mA) 260 max

Consumption in stand-by mode

with AC power supply (mA) 120

Power supply (VDC) 14÷18

Consumption with DC power supply (mA) 180 max

Consumption in stand-by mode

with DC power supply (mA) 80

Operating temperature (°C) 0 ÷ +35

Available functions

a) Up to 100 user codes can be stored. The codes can be of 3,

4 or 5 ﬁ gures, with a value from 001 to 65535. Each code can

be associated to one of the 2 relays.

b) The module is equipped with 2 relays for services with the

following operating features:

- Programmable activation time for each relay (from 1 to 65

seconds);

- Monostable or bistable operation for each relay;

- Option to lock in active status the relays in monostable opera-

tion, by pressing the key before the activation time runs out

(to deactivate it re-enter the same code); relay 2 can if neces-

sary be associated to an alarm or bell activation service (by ﬁ rst

enabling function 09).

Activation of the alarm

Relay 2 is activated by pressing before the user code (to

deactivate it see function 10).

All the user codes associated to relay 1 are enabled upon ac-

tivation of the alarm.

Activation of the bell

Relay 2 is activated only by pressing . In order to avoid the

alarm signal being sent inadvertently, the option to associate

user codes to relay 2 is automatically blocked.

c) When a key is pressed, beeps are generated to conﬁ rm the

di erent programming stages, in the following ways:

- Key pressed = short beep;

- Correct operation = long beep;

- Incorrect operation = three short beeps.

d) The status of the module and the functions in progress are

shown with LEDs :

- green LED A can be programmed to be:

• Light signal linked to beep.

• Disabled.

• Commanded by input I1.

- yellow LED B,

Pulsing = conﬁ rmation of activation of services.

Page 7 - Manual FA01425-EN - 02/2021 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions

- green LED C,

Always on = in operation,

Flashing = being programmed.

The LEDs light up 1 min after the equipment is powered up

(within which it is possible to carry out a reset of the equip-

ment).

e) It is possible to disable the keypad for an indeterminate time

using a special code, e.g. for prolonged absences (see function

12).

f) The keypad is locked for a time that can be programmed if a

valid code has not been entered after 20 ﬁ gures are keyed in

(see function 07).

g) There is an input I1 for an electrical contact with a program-

mable function to activate relay 1, enable Tradesman function,

or command the green LED A (see function 11).

h) Tradesman: this function allows relay 1 to be enabled only

when contact I1 is grounded (with external timer) and only for

user codes associated to service 3 (see function 03).

i) The default conﬁ guration values can be restored

using the RESET function (see reset procedure).

The stored user codes and the number of ﬁ gures programmed

are retained.

Default values with which the module is provided

Programming code: (5 ﬁ gures).

Reset code: not programmable;

User code on relay 1: .

User code on relay 2: .

Activation time for service relays: 5 seconds.

Activation type for service relays: monostable.

Number of ﬁ gures for user codes: 4.

Keypad locking time: 10 seconds.

Bell: disabled.

Bell duration: 3 seconds.

• Alarm: disabled.

• Keypad: enabled.

• Input for contact I1: command from relay 1.

• Green LED A: disabled.

Programming procedure

Function programming sequence.

1. To enter programming mode, press keys 1 and 3 at the

same time. Key in the PROGRAMMING CODE (default

12345), the green LED C will ﬂ ash.

2. Key in the FUNCTION CODE required (see list of function

codes).

To change the function code selected, press button or

and select a new function code.

3. Key in the required data.

A long beep indicates that the data has been recorded.

Three short beeps indicate an error.

4. After entering the data required a new function code can be

selected or the programming mode terminated by entering

99 (the green LED C stops ﬂ ashing).

List of function codes

After accessing programming mode (green LED C ﬂ ashing),

enter the desired function code:

FUNCTION CODE

Changing programming code (default 12345).

- Key in the new PROGRAMMING CODE (5 ﬁ gures).

FUNCTION CODE

Changing number of ﬁ gures in user code (default 4).

All the user codes have the same number of ﬁ gures.

- Key in the NUMBER OF FIGURES (3 or 4 or 5).

FUNCTION CODE

Adding a user code

(default relay 1=2580, relay 2=3690).

- Key in the number of the SERVICE to be programmed (1 or

2 or 3):

= activation of relay 1,

= activation of relay 2,

= activation of relay 1 in Tradesman operation (see function

11).

- Key in the USER CODE (3 or 4 or 5 ﬁ gures).

- Repeat the procedure to enter a new user code.

FUNCTION CODE

Deleting a user code.

- Key in the USER CODE to be deleted.

FUNCTION CODE

Deleting all user codes.

- Key in (USER CODE DELETION).

FUNCTION CODE

Setting service relays activation time (default 5 s).

- Select the desired RELAY by pressing or .

- Key in the ACTIVATION TIME from to seconds.

- Repeat the procedure to set the activation time of the other

relay.

FUNCTION CODE

Setting the keypad locking time, resulting from repeatedly

entering non-existent codes (default 10 s)

- Key in the LOCKING TIME from to seconds.

FUNCTION CODE

Setting monostable or bistable mode of relays (default mon-

ostable)

- Key in the desired SERVICE/RELAY.

= activation of relay 1,

= activation of relay 2,

= activation of relay 1 in Tradesman operation.

- Key in TYPE OF ACTIVATION

= BISTABLE

= MONOSTABLE

- Repeat the procedure to set another service/relay.

Page 8 - Manual FA01425-EN - 02/2021 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions

FUNCTION CODE

Enabling/disabling alarm and bell (default disabled)

- Key in the mode:

= DISABLED

= ALARM ENABLED

= BELL ENABLED

NOTE. Enabling the alarm or the bell disables the settings

of relay 2.

FUNCTION CODE

Reset alarm

FUNCTION CODE

Programming input I1 (default command relay 1).

- Key in:

= Command relay 1

= Enable Tradesman

= Command green LED A

= Disabled

FUNCTION CODE

Enabling/disabling keypad (default enabled).

- Key in:

= Disabled

= Enabled

FUNCTION CODE

Programming green LED A

- Key in:

= Disabled

= Access by pressing any button

Note. Programming is not possible if the LED is already

associated to input I1 (see function 11).

Reset procedure

- Cut power to the device.

- Repower the device again (green LED C o ).

- Key in the RESET CODE within 1 min from switch-on.

Note. The stored user codes and the number of ﬁ gures pro-

grammed are retained.

521 811 12 14

Page 9 - Manual FA01425-EN - 02/2021 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions

Wall-mounted installation

Fix the two hole covers to the base .

Attach the recessed box (with 3 modules

or round Ø 65 mm) ﬂ ush with the wall

and at a suitable height; ﬁ x the base to

the wall using the screws and expansion

plugs provided .

In systems where the Larsen e ect

might occur, the microphone can be

mounted remotely .

To remove the microphone from its

housing, pry it o its base using a

small screwdriver, taking care not to

damage the cabling .

Before inserting the microphone in the

bottom part of the back-box, use pliers

to remove the part that is highlighted .

Insert the audio unit near the top of the

base .

Apply the micro-contact (bottom high) in

the relevant seat . Perform the wiring.

Insert the HNA/102 access control mod-

ule at the bottom and fasten it using the

screw provided .

521 811 12 14

Button assembly

To write the desired information on the name card, take out

the card holder and the card. Personalised name cards up to a

maximum of 2 mm thick can be used.

Closing the front plate

To ﬁ t the front plate, ﬁ rst insert the upper part into the top and

then, using a 2.5 hex key, tighten the locking screw.

521 811 12 14

Page 10 - Manual FA01425-EN - 02/2021 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions

Wall mounting side by side

To mount the entry panels side by side horizontally, insert two hole covers into the exposed sides, and inside, the cable gland joint

at the bottom and the joint at the top .

Attach the assembled bases to the wall, using the screws and expansion plugs provided .

Page 11 - Manual FA01425-EN - 02/2021 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions

TARGHA 200

Accessories

HTS

Recess-mounting box

Frame

Cable gland joints

Spacer

Screws

KHPS

Button

Microcontact

Button spring

KHPD

Buttons

Microcontacts

Button springs

HBP

Wall-mounted base

Hole cover

Cable gland joint

Joint

Screws and expansion plugs

HPP/6 – HPP/12D

Front plate

Microcontacts with

common call

Lighting assembly

Cable holders

Hole cover

CAME S.p.A.

Via Martiri Della Libertà, 15

31030 Dosson di Casier - Treviso - Italy

tel. (+39) 0422 4940 - fax. (+39) 0422 4941

Page 12 - Manual FA01559-EN - 02/2021 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions