Emtek Narrow Oval & Modern Rectangular Pocket Door Mortise Lock Door Prep & Installation guide

Emtek
Brand
Emtek
Model
Narrow Oval & Modern Rectangular Pocket Door Mortise Lock Door Prep &
Type
Installation guide
IN4-PCKMRLKINS REV 4 1/12/2023
9/64" DEEP
FOR BOX
PLATE
3-7/8" DEEP
FOR MORTISE
BOX
DOOR
EDGE OF DOOR
L
C
NARROW OVAL & NARROW MODERN RECTANGULAR
POCKET DOOR MORTISE
DOOR PREPARATION TEMPLATE
7
8"
81
16"
11
16"
63
4"
6-3/8" X 1-3/4"
OVAL POCKET
FULL RADIUS
THRU ALL
63
8"
13
4"
EDGE OF DOOR
7
8"
23
16" BACKSET
33
8"
71
8"
FULL
RADIUS
7
16"DRILL PILOT HOLE
Ø1/8" X 3/4" DEEP
R
115
16"
DOOR JAMB PREP
7/8" DEPTH
LOCK
L
C
5/64" DEEP
FOR STRIKE PLATE
13
16"
39
16"
1
2"
11
16"
(1
8")
37
8"
5
16"
5
16"
DRILL PILOT HOLE
Ø1/8" X 3/4" DEEP
FOR KEYED &
PRIVACY TRIM
ONLY
Narrow Oval & Narrow Modern
Rectangular Pocket Mortise PM PM
Narrow Oval & Narrow Modern
Rectangular Pocket Mortise
NOTE:
THIS TEMPLATE IS DESIGNED
FOR 1-3/8" THICK DOOR.
123
1
2
3
Caution:
If printed from electronic file
set print scale to 1:1, print on
8-1/2" x 11" size paper.
Measure with ruler to check
scale.
See template for door prep
specications
1. Thread Drive Bar Cylinder
4. Tighten Key Cylinder
3. Install Outside Plate and Thread Key Cylinder
Install Key Cylinder by
threading it clockwise onto
lock body plate.
TRIMS VARY
NARROW OVAL SHOWN
Cylinder Key
Note: Notches on cylinder must be
parallel with the horizontal plane
when screwed ush into lock body.
Note: Key Cylinder notches must
be parallel with the horizontal
plane when fully screwed into
lock body.
Use Cylinder Key to thread Drive Bar
Cylinder clockwise on interior side of
door.
2. Install Lock Body
Outside
Inside
Inside
Tighten locking screw
to engage notches on
cylinder
6. Install Trim Plate
5. Mount Inside Plate
Door Jamb Prep.
See template for door jamb
prep specications
IN4-PCKMRLKINS REV. 4 1/12/2023
Inside
Keyed Function
Installation Guide Narrow Oval & Narrow Modern Rectangular Pocket Mortise
1. Thread Drive Bar Cylinder
Inside
4. Tighten Drive Bar Cylinder
3. Install Inside and Outside Plates
Cylinder Key
Note: Notches on cylinder must be
parallel with the horizontal plane
when screwed ush into lock body.
Use Cylinder Key to thread Drive Bar
Cylinder clockwise on interior side of
door.
2. Install Lock Body
Outside
Tighten locking screw to engage notches on cylinder
5. Install Trim Plate Door Jamb Prep.
See template for door jamb
prep specications
Align Passage/Privacy button with Thumb-turn
tail piece and secure trim pates to door.
See template for door prep
specications
TRIMS VARY NARROW OVAL SHOWN
Inside
IN4-PCKMRLKINS REV. 4 1/12/2023
Privacy Function
Installation Guide Narrow Oval & Narrow Modern Rectangular Pocket Mortise
Inside
Passage Trim shown
1. Install Lock Body
4. Install Trim Plate
2. Install Outside Plate
3. Install Inside Plate
See template for door prep
specications
TRIMS VARY
NARROW OVAL SHOWN
IN4-PCKMRLKINS REV. 4 1/12/2023
Passage/Dummy Function
Installation Guide Narrow Oval & Narrow Modern Rectangular Pocket Mortise
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Emtek Narrow Oval & Modern Rectangular Pocket Door Mortise Lock Door Prep & Installation guide

Emtek
Brand
Emtek
Model
Narrow Oval & Modern Rectangular Pocket Door Mortise Lock Door Prep &
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents