Emtek Classic Pocket Door Mortise Lock Door Prep & Installation guide

Emtek
Brand
Emtek
Model
Classic Pocket Door Mortise Lock Door Prep &
Type
Installation guide
IN4-
C
LP
C
KTM
R
TINS
R
EV
1
1
/
1
2/23
9/64" DEEP
FOR BOX
PLATE
3-7/8" DEEP
FOR MORTISE
BOX
115
16"
DOOR JAMB PREP
7/8" DEPTH
DOOR
EDGE OF DOOR
L
C
LOCK
L
C
5/64" DEEP
FOR STRIKE PLATE
13
16"
39
16"
CLASSIC POCKET DOOR MORTISE
DOOR PREPARATION TEMPLATE
7
8"
81
16"
11
16"
63
4"
1
2"
2-3/16" X 6-7/16"
RECTANGULAR HOLE
THRU ALL
67
16"
23
16"
EDGE OF DOOR
11
16"
1
8"
13
16"
23
16" BACKSET
33
8"
71
8"
FULL
RADIUS
7
16"DRILL PILOT HOLE
Ø1/8" X 3/4" DEEP
37
8"
5
16"
5
16"
DRILL PILOT HOLE
Ø1/8" X 3/4" DEEP
DRILL 4X PILOT HOLES
Ø1/8" X 3/4" DEEP
FOR KEYED &
PRIVACY TRIM
ONLY
1
8"
13
4"
7
8"
NOTE:
THIS TEMPLATE IS DESIGNED
FOR 1-3/8" THICK DOOR.
R
CLASSIC POCKET MORTISE PM CLASSIC POCKET MORTISE PM
123
1
2
3
Caution:
If printed from electronic file
set print scale to 1:1, print on
8-1/2" x 11" size paper.
Measure with ruler to check
scale.
See template for door prep
specications
Install Key Cylinder by
threading it clockwise
onto lock body plate
Key Cylinder notch
must be at the horizontal
position when fully screwed
in lock body.
Tighten locking screw to engage
notch on cylinder
See template for door jamb
prep specications
Drill two 7/64”
pilot holes
2. Install Lock Body
4. Mount Outside Plate
7. Install Trim Plate
1. Install Drive Bar Cylinder
5. Thread Key Cylinder
8. Install Door Jamb
6. Tighten Drive Bar Cylinder
3. Mount Inside Plate
Note: Notches on cylinder must be
parallel with the horizontal plane when
screwed ush into lock body.
Use Cylinder Key to thread Drive Bar
Cylinder clockwise on interior side of door.
Cylinder Key
Inside
Inside
IN4-CLPCKTMRTINS REV. 1 1/12/23
Keyed Function
Installation Guide Classic Pocket Door Mortise Lock
See template for door prep
specications
See template for door jamb
prep specications
Drill two 7/64”
pilot holes
2. Install Lock Body
4. Mount Inside/Outside Plates
5. Install Trim Plate
1. Install Drive Bar Cylinder
6. Install Door Jamb
3. Tighten Drive Bar Cylinder
Inside
Outside
Align Passage/Privacy Button with Thumb-Turn tail piece and secure trim plates to door.
Note: Notches on cylinder must be
parallel with the horizontal plane when
screwed ush into lock body.
Use Cylinder Key to thread Drive Bar
Cylinder clockwise on interior side of door.
Cylinder Key
Inside
Inside
IN4-CLPCKTMRTINS REV. 1 1/12/23
Privacy Function
Installation Guide Classic Pocket Door Mortise Lock
Tighten locking screw to engage
notch on cylinder
See template for door prep
specications
1. Install Lock Body
3. Install Inside Plate
2. Install Outside Plate
4. Install Trim Plate
IN4-CLPCKTMRTINS REV. 1 1/12/23
Passage/Dummy Function
Installation Guide Classic Pocket Door Mortise Lock
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Emtek Classic Pocket Door Mortise Lock Door Prep & Installation guide

Emtek
Brand
Emtek
Model
Classic Pocket Door Mortise Lock Door Prep &
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents