2. Emtek
  3. #8 Classic Arched Pocket Door Mortise Lock Door Prep &

Emtek #8 Classic Arched Pocket Door Mortise Lock Door Prep & Installation guide

  • Hello! I am a chat assistant and I have read the installation guide for EMTEK's NO. 8 Pocket Door Mortise. This document provides instructions for installing the mortise in keyed, privacy and passage/dummy configurations, including the necessary steps and important template references for door and jamb preparation. I am ready to answer any questions you have about this product.
  • What is the purpose of the cylinder key?
    What should be done before installing the lock body?
    Where can I find door jamb preparation details?
IN4-NO8PCKMRTINS REV 3 1/12/2023
9/64" DEEP
FOR BOX
PLATE
3-7/8" DEEP
FOR MORTISE
BOX
115
16"
DOOR JAMB PREP
7/8" DEPTH
DOOR
EDGE OF DOOR
L
C
LOCK
L
C
5/64" DEEP
FOR STRIKE PLATE
13
16"
39
16"
NO. 8 POCKET DOOR MORTISE
DOOR PREPARATION TEMPLATE
7
8"
81
16"
11
16"
63
4"
1
2"
6-1/4" X 2"
OVAL POCKET
FULL RADIUS
THRU ALL
61
4"
2"
EDGE OF DOOR
11
16"
(1
8")
15
16"
23
16" BACKSET
33
8"
71
8"
FULL
RADIUS
1
2"
DRILL PILOT HOLE
Ø1/8" X 3/4" DEEP
37
8"
5
16"
5
16"
DRILL PILOT HOLE
Ø1/8" X 3/4" DEEP
FOR KEYED &
PRIVACY TRIM
ONLY
R
NO. 8 STYLE POCKET MORTISE PM NO. 8 STYLE POCKET MORTISE PM
NOTE:
THIS TEMPLATE IS DESIGNED
FOR 1-3/8" THICK DOOR.
123
1
2
3
Caution:
If printed from electronic file
set print scale to 1:1, print on
8-1/2" x 11" size paper.
Measure with ruler to check
scale.
See template for door prep
specications
1. Thread Drive Bar Cylinder
4. Tighten Key Cylinder
3. Install Outside Plate and Thread Key Cylinder
Install Key Cylinder by
threading it clockwise onto
lock body plate.
Cylinder Key
Note: Notches on cylinder must
be parallel with the horizontal plane
when screwed ush into lock body.
Note: Key Cylinder notches must
be parallel with the horizontal
plane when fully screwed into
lock body.
Use Cylinder Key to thread Drive Bar
Cylinder clockwise on interior side of
door.
2. Install Lock Body
Outside
Tighten locking screw
to engage notches on
cylinder
6. Install Trim Plate
5. Mount Inside Plate
Door Jamb Prep.
See template for door jamb
prep specications
IN4-NO8PCKMRTINS REV. 3 1/12/2023
Inside
Keyed Function
Installation Guide #8 Pocket Door Mortise
See template for door prep
specications
1. Thread Drive Bar Cylinder
Inside
Inside
4. Tighten Drive Bar Cylinder
3. Install Inside and Outside Plates
Cylinder Key
Note: Notches on cylinder must be
parallel with the horizontal plane
when screwed ush into lock body.
Use Cylinder Key to thread Drive Bar
Cylinder clockwise on interior side of
door.
2. Install Lock Body
Outside
Tighten locking screw to engage notches on cylinder
5. Install Trim Plate Door Jamb Prep.
See template for door jamb
prep specications
Align Passage/Privacy button with Thumb-turn
tail piece and secure trim pates to door.
IN4-NO8PCKMRTINS REV. 3 1/12/2023
Privacy Function
Installation Guide #8 Pocket Door Mortise
Passage Trim shown
1. Install Lock Body
4. Install Trim Plate
2. Install Outside Plate
3. Install Inside Plate
See template for door prep
specications
IN4-NO8PCKMRTINS REV. 3 1/12/2023
Passage/Dummy Function
Installation Guide #8 Pocket Door Mortise
/