Pioneer KEH-P2035 Owner's manual

Brand: Pioneer

Model: KEH-P2035

Category: Car media receivers

Type: Owner's manual

Pioneer KEH-P2035 is a car audio system that combines a radio tuner with a CD player and additional connectivity options. It features a DIN front/rear-mount design, allowing for flexible installation in a variety of vehicles. The system includes a 182 x 53 mm front panel and a detachable faceplate for added security.

The KEH-P2035 supports a wide range of audio formats, including CD, CD-R, and CD-RW discs. It offers various playback options, such as track search, repeat, and random play. Additionally, the system features an AM/FM tuner with manual and automatic station search functions, providing access to a variety of radio channels.

30˚

182

KEH-P2035

Printed in Malaysia

<CZR2956-A> ES

This product conforms to new cord colors.

Los colores de los cables de este producto se

conforman con un nuevo código de colores.

u« l “UN'« «c¼ r−M¹Æ…b¹b'« „öÝô« Ê«

Fig. 4

¥ qJA«

Note:

• Before finally installing the unit, connect the

wiring temporarily, making sure it is all connect-

ed up properly, and the unit and the system work

properly.

• Use only the parts included with the unit to

ensure proper installation. The use of unautho-

rized parts can cause malfunctions.

• Consult with your nearest dealer if installation

requires the drilling of holes or other modifica-

tions of the vehicle.

• Install the unit where it does not get in the dri-

ver’s way and cannot injure the passenger if there

is a sudden stop, like an emergency stop.

• The semiconductor laser will be damaged if it

overheats, so don’t install the unit anywhere hot

— for instance, near a heater outlet.

• If installation angle exceeds 30° from horizontal,

the unit might not give its optimum performance.

(Fig. 1)

DIN Front/Rear-mount

This unit can be properly installed either from

“Front” (conventional DIN Front-mount) or

“Rear” (DIN Rear-mount installation, utilizing

threaded screw holes at the sides of unit chassis).

For details, refer to the following illustrated

installation methods.

DIN Front-mount

Installation with the rubber bush (Fig. 2)

1. Dashboard

2. Holder

After inserting the holder into the dashboard,

then select the appropriate tabs according to the

thickness of the dashboard material and bend

them.

(Install as firmly as possible using the top and

bottom tabs. To secure, bend the tabs 90

degrees.)

3. Rubber bush

4. Screw

Removing the Unit (Fig. 3) (Fig. 4)

5. Frame

6. Insert the release pin into the hole in the bottom

of the frame and pull out to remove the frame.

(When reattaching the frame, point the side with

a groove downwards and attach it.)

7. Insert the supplied extraction keys into the unit,

as shown in the figure, until they click into place.

Keeping the keys pressed against the sides of the

unit, pull the unit out.

DIN Rear-mount

Installation using the screw holes on

the side of the unit (Fig. 5) (Fig. 6) (Fig. 7)

1. Remove the frame.

8. Frame

9. Insert the release pin into the hole in the bottom

of the frame and pull out to remove the frame.

(When reattaching the frame, point the side with

a groove downwards and attach it.)

2. Fastening the unit to the factory

radio mounting bracket.

10. Select a position where the screw holes of the

bracket and the screw holes of the head unit

become aligned (are fitted), and tighten the

screws at 2 places on each side. Use either truss

screws (5 × 8 mm) or flush surface screws

(5 × 9 mm), depending on the shape of the screw

holes in the bracket.

11. Screw

12. Factory radio mounting bracket

13. Dashboard or Console

Installation <ENGLISH>

Fig. 2

≤ qJA«

Fig. 1

± qJA«

Fig. 3

≥ qJA«

Fig. 5

µ qJA«

Fig. 6

∂ qJA«

Fig. 7

∑ qJA«

INSTALLATION MANUAL

CZR2956-A 8/5/02 16:03 Page 1

Page is loading ...

13. Blue/white

To system control terminal of the power amp

or Auto-antenna relay control terminal (max.

300mA 12 V DC).

11. Connecting cords with RCA pin plugs

(sold separately)

14. System remote control

21. Right

16. White

18. Gray

17. White/black

23. Green

24. Green/black

19. Gray/black

25. Violet

26. Violet/black

15. Front speaker

20. Left

29. Perform these connections when using

the optional amplfier.

28. With a 2 speaker system, do not connect

anything to the speaker leads that are not

connected to speakers.

22. Rear speaker 22. Rear speaker

15. Front speaker

27. Rear speaker 27. Rear speaker

12. Power amp

(sold separately)

1. This Product

4. IP-BUS input (Blue)

3.Antenna jack

2. Rear output

5. Multi-CD player

(sold separately)

6. IP-BUS cable

9. Black (ground)

To vehicle (metal) body.

8. Red

To electric terminal controlled by ignition switch

(12 V DC) ON/OFF.

7. Yellow

To terminal always supplied with power regardless of

ignition switch position.

10. Fuse

Note:

• This unit is for vehicles with a 12-volt battery

and negative grounding. Before installing it in a

recreational vehicle, truck, or bus, check the bat-

tery voltage.

• To avoid shorts in the electrical system, be sure

to disconnect the ≠ battery cable before begin-

ning installation.

• Refer to the owner’s manual for details on con-

necting the power amp and other units, then

make connections correctly.

• Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around them where they lie against metal parts.

• Route and secure all wiring so it cannot touch

any moving parts, such as the gear shift, hand-

brake and seat rails. Do not route wiring in

places that get hot, such as near the heater outlet.

If the insulation of the wiring melts or gets torn,

there is a danger of the wiring short-circuiting to

the vehicle body.

• Don’t pass the yellow lead through a hole into

the engine compartment to connect to the battery.

This will damage the lead insulation and cause a

very dangerous short.

• Do not shorten any leads. If you do, the protec-

tion circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply lead of the

unit and tapping into the lead. The current capac-

ity of the lead will be exceeded, causing over-

heating.

• When replacing fuse, be sure to use only fuse of

the rating prescribed on the fuse holder.

• Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded or

the left and right ≠ speaker leads are common.

• Speakers connected to this unit must be high-

power types with minimum rating of 45 W and

impedance of 4 to 8 ohms. Connecting speakers

with output and/or impedance values other than

those noted here may result in the speakers catch-

ing fire, emitting smoke, or becoming damaged.

• When this product’s source is switched ON, a

control signal is output through the blue/white

lead. Connect to an external power amp’s system

remote control or the car’s Auto-antenna relay

control terminal (max. 300 mA 12 V DC). If the

car features a glass antenna, connect to the anten-

na booster power supply terminal.

• When an external power amp is being used with

this system, be sure not to connect the blue/white

lead to the amp’s power terminal. Likewise, do

not connect the blue/white lead to the power ter-

minal of the auto-antenna. Such connection could

cause excessive current drain and malfunction.

• To avoid short-circuiting, cover the disconnected

lead with insulating tape. Especially, insulate the

unused speaker leads without fail. There is a pos-

sibility of short-circuiting if the leads are not

insulated.

• To prevent incorrect connection, the input side of

the IP-BUS connector is blue, and the output side

is black. Connect the connectors of the same col-

ors correctly.

• If this unit is installed in a vehicle that does not

have an ACC (accessory) position on the ignition

switch, the red lead of the unit should be con-

nected to a terminal coupled with ignition switch

ON/OFF operations. If this is not done, the vehi-

cle battery may be drained when you are away

from the vehicle for several hours.

• The black lead is ground. Please ground this lead

separately from the ground of high-current prod-

ucts such as power amps.

If you ground the products together and the

ground becomes detached, there is a risk of dam-

age to the products or fire.

• Cords for this product and those for other prod-

ucts may be different colors even if they have

the same function. When connecting this prod-

uct to another product, refer to the supplied

Installation manuals of both products and con-

nect cords that have the same function.

Connecting the Units

ACC position

No ACC position

Connection Diagram (Fig. 8)

1. This Product

2. Rear output

3. Antenna jack

4. IP-BUS input (Blue)

5. Multi-CD player (sold separately)

6. IP-BUS cable

7. Yellow

To terminal always supplied with power regard-

less of ignition switch position.

8. Red

To electric terminal controlled by ignition switch

(12 V DC) ON/OFF.

9. Black (ground)

To vehicle (metal) body.

10. Fuse

11. Connecting cords with RCA pin plugs (sold sep-

arately)

12. Power amp (sold separately)

13. Blue/white

To system control terminal of the power amp or

Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

14. System remote control

15. Front speaker

16. White

17. White/black

18. Gray

19. Gray/black

20. Left

21. Right

22. Rear speaker

23. Green

24. Green/black

25. Violet

26. Violet/black

27. Rear speaker

28. With a 2 speaker system, do not connect anything

to the speaker leads that are not connected to

speakers.

29. Perform these connections when using the

optional amplifier.

Fig. 8

∏ qJA«

CZR2956-A 8/5/02 16:03 Page 13

Page is loading ...

Pioneer KEH-P2035 Owner's manual

Brand: Pioneer

Model: KEH-P2035

Category: Car media receivers

Type: Owner's manual

Download PDF

report

in other languages

español: Pioneer KEH-P2035 El manual del propietario
português: Pioneer KEH-P2035 Manual do proprietário

Pioneer KEH-P2035 Owner's manual

Pioneer KEH-P2035 Owner's manual

in other languages

Related papers

Other documents