JVC SP-XF30 is a satellite speaker system designed to enhance your home audio experience. The system includes front speakers, a center speaker, surround speakers, and a surround back speaker. The speakers are magnetically shielded to prevent distortion on TVs. With a maximum power handling capacity of 100 W, the speakers deliver clear and dynamic sound. The system is easy to assemble and connect, making it a great choice for both home theater and music listening.
JVC SP-XF30 is a satellite speaker system designed to enhance your home audio experience. The system includes front speakers, a center speaker, surround speakers, and a surround back speaker. The speakers are magnetically shielded to prevent distortion on TVs. With a maximum power handling capacity of 100 W, the speakers deliver clear and dynamic sound. The system is easy to assemble and connect, making it a great choice for both home theater and music listening.
SATELLITE SPEAKER SYSTEM
SP-XF70 / SP-XF30
INSTRUCTIONS
LVT1167-002A
[US]
SP-XF30C
SP-XF70C
SP-XF30S
SP-XF30F
SP-XF30F
SP-XF30S
SP-XF70S
• Only for SP-XF70
Cover_SP-XF70_30[US]f.p65 11/3/04, 4:08 PM1
– 2 –
Precautions for installation
• Do not install the speakers on an uneven surface or in a place subject
to vibration; otherwise, they may fall over, causing damage or injury.
• The speakers are magnetically shielded to avoid color distortions on
TVs if they are installed properly.
– When placing the speakers near a TV set, turn off the TV’s main
power switch or unplug it before installing the speakers.
Then wait at least 30 minutes before turning on the TV’s main power
switch again. If there are still distortion, move the speakers further
away from the TV.
Precautions for daily use
• Do not reproduce sounds at so high a volume that they are distorted;
otherwise, the speakers may be damaged by internal heat buildup.
• When moving the speakers, do not pull the speaker cords; otherwise,
the speakers may fall over, causing damage or injury.
• When holding a speaker, always grasp the lower portion.
Checking the Components
Check to be sure you have the following components.
The number in parenthesis indicates the quantity of the piece supplied.
• Speaker cords— 4 m (3): For front/center speakers
• Speaker cords— 10 m (2): For surround speakers
• Screws— M5 x 25 mm (8)
Surround
speakers (2)
Front
speakers (2)
Stands (4)
Base plates (4)
Surround back speaker (1) and
Speaker cord— 10 m (1)
Only for SP-XF70
Center speaker (1)
If any of the items above are missing, contact your dealer immediately.
Thank you for purchasing JVC speakers.
Before you begin using them, please read the instructions carefully.
Contents
Warnings, Cautions and Others ................................................................................................. 2
Assembling the front and surround speakers ............................................................................ 3
Connections .............................................................................................................................. 4
Specification.............................................................................................................................. 8
English
Warnings, Cautions and Others
SP-XF70C
SP-XF30S
SP-XF30F SP-XF30F
SP-XF30S
SP-XF70S
SP-XF70
SP-XF30C
SP-XF30S
SP-XF30F SP-XF30F
SP-XF30S
SP-XF30
EN02-04_SP-XF70_30[US]f.p65 11/3/04, 4:09 PM2
– 3 –
English
SP-XF30S
SP-XF30F
Assembling the front and surround speakers
Assembled speakers: With stand: Refer to Steps
1
to
6
Without stand: Refer to Steps
1
to
5
Before assembling—
• Prepare a Philips screwdriver (not supplied).
• Take care not to drop any component part while assembling; otherwise, it may cause damage to the floor or injury.
• Each speaker cord has its name tag attached to one end. Attach the end without the name tag to the speaker terminal.
or
or
With stand With standWithout stand Without stand
6
5
4
3
2
1
Route the cord
Speaker cord
Base plate
(Rear side)
Speaker cord
Stand
(or speaker
directly)
Base plate
Screw
(M5 x 25 mm)
Press ReleaseInsert
Black striped
Black
Copper
Speaker
cord
Red
Stand
Speaker
White
Black
Continue on the next page
Screw
(M5 x 25 mm)
EN02-04_SP-XF70_30[US]f.p65 1/4/04, 4:59 PM3
– 4 –
SURROUND
SPEAKERS
LEFTRIGHT LEFTRIGHT
CENTERFRONT
CENTER
FRONT LEFT
FRONT RIGHT
SURROUND RIGHT
SURROUND LEFT
SURROUND BACK
SURROUND
BACK
English
Typical connection method to an amplifier
Connect the speakers to the speaker terminals of the amplifier with
the speaker cords by referring to the diagram below.
• Make sure to match the polarity (ª and ·) when connecting
the speaker cords.
• The diagram below is an example of a typical connection.
For SP-XF30:
Recommended to use
SP-SB100—optionally
purchased.
Speaker layout
Front left
Subwoofer
Amplifier
Surround rightSurround left
Center
Surround back
Front right
Only for SP-XF70
Connecting the Surround back speaker—Only for SP-XF70
Black striped
Copper
Red
Black
Press
ReleaseInsert
Connections
Connecting the speaker system to the amplifier
Before connecting—
• Turn off the power to the amplifier before connecting the speaker
system; otherwise, the speakers may be damaged.
• The impedance of each speaker is 6 Ω. Before connecting them to
your amplifier, check the speaker impedance range of your amplifier. If
the impedance of this speaker is out of the speaker impedance range
indicated on the amplifier, you cannot connect this system to the
amplifier.
• The maximum power handling capacity of the speakers are 100 W.
Excessive input will result in abnormal noise and possible damage.
• Be sure to turn down the volume level to prevent unwanted noise
before performing following operations:
– Turning on or off other components,
– Operating the amplifier,
– Tuning FM stations,
– Fast-forwarding a tape,
– Continuously reproducing high frequency oscillation or high pitch
electronic sounds.
• When using a microphone, do not aim it at the speakers or use it near
the speakers; otherwise, the howling which occurs may damage the
speakers.
• Before replacing the cartridge, always turn off the power to the
turntable; otherwise, the clicking noise may damage the speakers.
Connecting the Center speaker
Press ReleaseInsert
Black striped
Copper
Red
Black
EN02-04_SP-XF70_30[US]f.p65 1/4/04, 4:59 PM4
– 5 –
!"#$%&'()*+,-./0
= !"#$%
• !"#$%&'()*+,-./+012!"#345678
!"#$%&
• !"#$%&'()*+,*-./0123456789:;
– !"#$%&'()*+,-'%&"#$./0123()
!"#$%&'!"()*
!"#$%&'#()*+,-./=30= !"#$%&
!"#$%&'()*+!,-./012
= !"#$%&'
• !"#$%&'()*+(,-./(0"123'4567,
!"#$%&'
• !"#$%&'!"#()*+,!"#-./01(2345
!"
• !"#$%&'(!"#)*+,
= !
!"#$%&'()*+
!"#$%&'!"()
!"#$%1
!"#10 m1
!
==
==
=SP-XF70
!"JVC !"#
!"#$%&'()*+,- !./01
!"#$%KKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKK 5
!"#$%&'KKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKK 6
KKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKK 7
KKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKK 8
!"#$%
SP-XF70C
SP-XF30S
SP-XF30F SP-XF30F
SP-XF30S
SP-XF70S
SP-XF70
SP-XF30C
SP-XF30S
SP-XF30F SP-XF30F
SP-XF30S
SP-XF30
!"=E2F
!"=E2F =E4F
=E4F
!"=E1F
• !"= 4 m3 !"#$%L !"
• !"== 10 m2 !"#$%&'(
• ==M5 × 25 mm8
Chi/MD2068 4/1/04, 3:06 PM5
– 6 –
SP-XF30S
SP-XF30F
!"#$%&'
!"#$ !"#=
1
==
6
============================ ! !"#=
1
==
5
!"#$
• !"#$%&'()*+
• !"#$%&'()*+,-./0123456789:
• !"#$%&'()*+,-./0 !"#$%&'()*+,-
! !
6
5
4
3
2
1
!
!"
!"
!"
E !
!F
EM5 x 25 mmF
!"
!"
EM5 x 25 mmF
Chi/MD2068 4/1/04, 3:07 PM6
– 7 –
SURROUND
SPEAKERS
LEFTRIGHT LEFTRIGHT
CENTERFRONT
CENTER
FRONT LEFT
FRONT RIGHT
SURROUND RIGHT
SURROUND LEFT
SURROUND BACK
SURROUND
BACK
= !"#$%&'()*
!"#$%&'()$%&*+,-./0&1$%&23
• !"#$%&'()*+, Eª ·F
• !"#$%&'()
==
==
=SP-XF30:
!=SP-SB100
E !"F
= !"#
!"#
!"#
!"
!"# !"#
!"#$
!"#
!
==
==
=SP-XF70
= !"#$%&'()*+
==
==
=SP-XF70
!"
= !"#$%&'()*!+
!"#$
• !"#$%&'()*+,-./0#123(456789!
• !"#$%&=6=Ω !"#$%&'()*+,#-./0
!"#$%&'()*+,-&./01234,-&+./5
!"#$%&'()$*+,-./0123()$4567
!"#$%
• !"#$%&'(=100 W
!"#$%&'()*+,-./0123456789
• !"#$%&'()*+,-./01234567+8
– !"#$%&'
– !"#$%
– FM=
– !"#$
– !"#$%&"'()*+
• !"#$%&'()*+,-.%/&',-.01 %23
!"#$%&'(
• !"#$%&'()*!+,-.%/0123456789:
= !"#$%
!"
!"
Chi/MD2068 4/1/04, 3:07 PM7
– 8 –
English
Specification / /
SP-XF30F (Front speakers)
Type: 2-way 3-speaker Bass reflex type (Magnetically-shielded type)
Speaker unit: 5.5 cm cone (× 2), 3.0 cm dome
Frequency range: 95 Hz to 40 000 Hz
Input impedance: 6 Ω
Power handling Capacity: 100 W
Sound pressure level: 80 dB/W•m
Dimensions: 250 mm (W) × 1 103 mm (H) × 250 mm (D)
Mass: 3.67 kg each
SP-XF30S (Surround speakers)
Type: 2-way 3-speaker Bass reflex type (Magnetically-shielded type)
Speaker unit: 5.5 cm cone (× 2), 3.0 cm dome
Frequency range: 90 Hz to 40 000 Hz
Input impedance: 6 Ω
Power handling Capacity: 100 W
Sound pressure level: 77 dB/W•m
Dimensions: 250 mm (W) × 1 103 mm (H) × 250 mm (D)
Mass: 3.83 kg each
SP-XF70C / SP-XF30C (Center speaker)
Type: 2-way 3-speaker Bass reflex type (Magnetically-shielded type)
Speaker unit: 5.5 cm cone (× 2), 3.0 cm dome
Frequency range: 90 Hz to 40 000 Hz
Input impedance: 6 Ω
Power handling Capacity: 100 W
Sound pressure level: 81 dB/W•m
Dimensions: 209 mm (W) × 85 mm (H) × 92 mm (D)
Mass: 0.87 kg
SP-XF70S (Surround back speaker)
Type: 2-way 3-speaker Bass reflex type (Magnetically-shielded type)
Speaker unit: 5.5 cm cone (× 2), 3.0 cm dome
Frequency range: 90 Hz to 40 000 Hz
Input impedance: 6 Ω
Power handling Capacity: 100 W
Sound pressure level: 78 dB/W•m
Dimensions: 84 mm (W) × 211 mm (H) × 120 mm (D)
Mass: 0.96 kg
Design and specifications are subject to change without notice.
SP-XF30F
W.m
SP-XF30S
W.m
SP-XF70C / SP-XF30C
W.m
SP-XF70S
W.m
EN08-08_SP-XF70_30[US]f.p65 1/4/04, 4:59 PM8
– 9 –
SURROUND
SPEAKERS
LEFTRIGHT LEFTRIGHT
CENTERFRONT
CENTER
FRONT LEFT
FRONT RIGHT
SURROUND RIGHT
SURROUND LEFT
SURROUND BACK
SURROUND
BACK
—
•
•
•
•
–
–
–FM
–
–
•
•
SP-XF70
•ª·
•
SP-XF30
SP-SB100
SP-XF70
––
ARA SP-XF70[US] 1/4/04, 10:42 AM9
– 10 –
SP-XF30F
—
•
•
•
123
M5
2
1
SP-XF30S
––
3
M5
ARA SP-XF70[US] 1/4/04, 10:42 AM10
– 11 –
•
•
–
•
•
•
JVC
(11)
(10)
(9)
(8)
•
•
•M5
SP-XF70
SP-XF70C
SP-XF30S
SP-XF30F SP-XF30F
SP-XF30S
SP-XF70S
SP-XF70
SP-XF30C
SP-XF30S
SP-XF30F SP-XF30F
SP-XF30S
SP-XF30
––
ARA SP-XF70[US] 1/4/04, 10:42 AM11
EN, CS, AR
© 2004 Victor Company of Japan, Limited
SP-XF70 / SP-XF30
SP-XF30C
SP-XF70C
SP-XF30S
SP-XF30F
SP-XF30F
SP-XF30S
SP-XF70S
LVT1167-002A
[US]
0304NSMMDWHCE
Cover_SP-XF70_30[US]f.p65 11/3/04, 4:08 PM2
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
JVC SP-XF30 is a satellite speaker system designed to enhance your home audio experience. The system includes front speakers, a center speaker, surround speakers, and a surround back speaker. The speakers are magnetically shielded to prevent distortion on TVs. With a maximum power handling capacity of 100 W, the speakers deliver clear and dynamic sound. The system is easy to assemble and connect, making it a great choice for both home theater and music listening.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Sony SA-RV999DX Operating instructions
-
Samsung CHT-350 User manual
-
-
Pioneer KEH-P2035 Owner's manual
-
-
-
-
-
Bosch WTC82100US Operat./Install.Instruct./Program table
-