arietta PRO001MX 30 Installation guide

PRO001MX 30 PRO001MX 36

Use, Care and Installation Guide

Guía de Instalación, Uso y Mantenimiento

Model Number

Número de Modelo

Serial Number

Número de Serie

Date of Purchase

Fecha de Compra

Sales Dealer

Distribuidor

READ AND SAVE THESE INSTRUCTIONS

LEA Y GUARDE ESTAS INSTRUCCIONES

LI225A

E N G L I S H

E S P A Ñ O L

2

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.

INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.

INSTALLER: Please leave these Instructions with this unit for the owner.

OWNER: Please retain these instructions for future reference.

Requirement: 120 VAC, 60 Hz. 15 or 20 A Branch Circuit

APPROVED FOR RESIDENTIAL APPLIANCES

FOR RESIDENTIAL USE ONLY

English page 2

Spanish page 25

3

Table of Contents

Important Safety Notice ..................................................................5-6

Electrical & Installation Requirements ............................................7

Electrical requirements ...............................................................7

Before installing the hood ...........................................................7

Product Dimensions and Clearances ...............................................8

Installing preparation ..................................................................8

List of Materials ..................................................................................9

Parts included in your hood ........................................................9

Optional accessories .................................................................9

Materials required ......................................................................9

Tools required for installation .....................................................9

Installation Instructions ..............................................................10-16

Installing the hood ................................................................... 11

Choosing the vent options ........................................................11

Ducting .....................................................................................11

Install framing for hood support ...............................................12

Ductwork installation guidelines ...............................................13

Discharge direction ..................................................................14

Wall mount installation .............................................................15

Cabinet installation ...................................................................15

Making the electrical connections ............................................16

4

Table of Contents

Use And Care Instructions .........................................................17-20

Control and features ................................................................18

Special Functions .....................................................................19

Clock programming ..................................................................19

 Greaseltersaturationalarm ...................................................19

 Charcoalltersaturationalarm(Recirculatingaccessories) ...

19

Audible signal activation and deactivation

...............................19

 Charcoallterinclusionandexclusion(Recirc.accessories)...19

Heat sensor .............................................................................19

 Metalgreaseltermaintenance ..............................................20

Hood maintenance ..................................................................

20

Lamp bulb maintenance ..........................................................20

Available Accessories ......................................................................21

Charcoallterplacement(Recirculatingaccessories) ............21

 Non-returnvalveinstallation(Recirculatingaccessories)........21

Trouble Shooting ..............................................................................22

List of Parts and Accessories .........................................................23

Warranty ............................................................................................24

5

Important Safety Notice

READ AND SAVE THESE INSTRUCTIONS

CAUTION:

For general ventilating use only. Do Not Use To Exhaust Hazardous or Explosive Materials, And Vapors.

CAUTION:

DURING THE HOOD INSTALLATION, THE PEOPLE INSTALLING THE HOOD MUST WEAR PROTECTION GLOVES

AGAINTS SHARP EDGES.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

• Use this unit only in the manner intended by the manufacturer. If you have questions, contact the

manufacturer.

• Before servicing or cleaning the unit, switch power off at the service panel and lock the service disconnecting

means to prevent power from being switched on accidentally. If the service disconnecting means cannot be

locked, securely fasten a prominent warning device, such as a tag, to the service panel.

• Installationworkandelectricalwiringmustbedonebyqualiedperson(s)inaccordancewithallapplicable

codes & standards, including Fire-rated construction.

• Sufcientairisneededforpropercombustion and exhaustingof gasesthrough theue (chimney)of fuel

burning equipment to prevent back- drafting. Follow the heating equipment manufacturers guideline and safety

standardssuchasthosepublishedbytheNationalFireProtectionAssociation(NFPA),theAmericanSociety

forHeating,RefrigerationandAirConditioningEngineers(ASHRAE),andthelocalcodeauthorities.

• When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

• Ducted fans must always be vented to the outdoors.

• Do not make alterations to the original wiring.

• Donotattempttorepairorreplaceanypartofyourhoodunlessitisspecicallyrecommendedinthismanual.

Allotherservicingshouldbereferredtoaqualiedtechnician.

• Avoidusingfoodproductsthatproduceamesundertherangehood.

CAUTION:

Toreduceriskofreandtoproperlyexhaustair,besuretoductairoutside-donotventexhaustairintospaceswithin

walls, ceilings, attics, crawl spaces, or garages.

Automatically operated device - to reduce risk of injury disconnect from power supply before servicing.

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCT WORK.

Installthishoodinaccordancewithallrequirementsspecied.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS HOOD WITH ANY EXTERNAL SO-

LIDSTATE SPEED CONTROL DEVICE.

6

Important Safety Notice

WARNING

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE.

• Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

• AlwaysturnhoodONwhencookingathighheatorwhenambeingfood(i.e.CrepesSuzette,CherriesJubilee,

PeppercornBeefFlambè).

• Cleanventilatingfansfrequently.Greaseshouldnotbeallowedtoaccumulateonfanorlters.

• Useproperpansize.Alwaysusecookwareappropriateforthesizeofthesurfaceelement.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS, IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE

THE FOLLOWING “

a

”:

• SMOTHERFLAMESwithaclose-ttinglid,cookiesheet,ormetaltray,thenturnofftheburner.BECAREFUL 

TOPREVENTBURNS.Iftheamesdonotgooutimmediately,

EVACUATE AND CALL THE FIRE DEPARTMENT.

• NEVERPICKUPAFLAMINGPAN-youmaybeburned.

• DONOTUSEWATER,includingwetdishclothsortowels-aviolentsteamexplosionwillresult.

• UseanextinguisherONLYif:

a) YouknowyouhaveaclassABCextinguisher,andyoualreadyknowhowtooperateit.

b) Thereissmallandcontainedintheareawhereitstarted.

c) Theredepartmentisbeingcalled.

d) Youcanghttherewithyourbacktoanexit.

“

a

”Basedon"KitchenFireSafetyTips"publishedbyNFPA.

Note To Installer

Be sure to leave these instructions to the customer.

Note To The Customer

• Keepthisinstructionmanualforfuturereference.

• Keepthisinstructionmanualforlocalinspector.

Operation

Alwaysleavesafetygrillsandltersinplace.Withoutthesecomponents,operatingblowerscouldcatchontohair,ngers

and loose clothing.

The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,

maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to negligence

andthewarrantyoftheunitautomaticallyexpiresduetoimpropermaintenance.

7

ELECTRICAL REQUIREMENTS

IMPORTANT:

• Observe all governing codes and ordinances.

• Itisthecustomer’sresponsibility:

o Tocontactaqualiedelectricalinstaller.

o To assure that the electrical installation is adequate and in conformance with National Electrical Code,

ANSI/NFPA70 latest edition* and all local codes and ordinances.

• Ifcodespermitandaseparategroundwireisused,itisrecommendedthataqualiedelectriciandeterminethat

the ground path is adequate.

• Do not ground to a gas pipe.

• Checkwithaqualiedelectricianifyouarenotsurethattherangehoodisproperlygrounded.

• Do not have a fuse in the neutral or ground circuit.

• Save installation instructions for electrical inspector’s use.

• The range hood must be connected with copper wire only.

• Therangehoodshouldbeconnecteddirectlytothefuseddisconnect(orcircuitbreaker)boxthroughmetalelectrical

conduit.

• WiresizesmustconformtotherequirementsoftheNationalElectricalCodeANSI/NFPA70latestedition*and

all local codes and ordinances.

• U.L.(underwrittersLaboratories)listedconduitconnectormustbeprovidedateachendofthepowersupplyconduit

(attherangehoodandatthejunctionbox).

*Copiesofthestandardslistedmaybeobtainedfrom:

National Fire Protection Association Batterymarch Park Quincy, Massachusetts 02269

Electric requirements

• Theseventhoodsmustbepowersupplied120V,60Hz,andconnectedtoanindividual,properlygroundedbranch

circuit, and protected by 15 or 20 Amps circuit breaker or fuse.

• Wiring must be two wire with ground.

• If the electrical supply does not meet above requirements, call a licensed electrician before proceeding.

• Routehousewiringasclosetotheinstallationlocationaspossible,intheceilingorbackwall.

• The hood must be connected to the house wiring in accordance with the local codes.

CAUTION: This appliance should be properly grounded.

Before installing the hood

• Forthemostefcientairowexhaust,useastraightrunorasfewelbowsaspossible.

CAUTION: Vent unit to outside of building only.

• At least two people are needed for installation.

• Onaverageonetothreehoursarenecessarytocompleteinstallation(withoutconsideringcuttobedoneonwall

and/oroncabinet,installationducts,conduitandelectricalconnectionstothemains).

• Thehoodisttedwithscrewssuitableforwoodenwalls,consultaqualiedinstaller,checkiftheyperfectlytwith

your cabinet/wall.

• Wall fastener anchors may be required for installation to concrete wall, etc.

• Donotuseexducting.

• COLDWEATHERinstallationsshouldhaveanadditionalnonreturnvalve(Accessorynotprovidedwiththehood)

installedtominimizebackwardcoldairowandathermalbreaktominimizeconductionofoutsidetemperatures

as part of the duct work. The damper should be on the cold air side of the thermal break. The break should be as

close as possible to where the ducting enters to the heated portion of the house.

• Make up air local building codes may require the use of makeup air systems when using ducted ventilation systems

greaterthanspeciedCFMofairmovement.ConsultyourHVACprofessionalforspecicrequirementsinyour

area.

Electrical & Installation Requirements

8

Product Dimensions and Clearances

Installing preparation

Advance planning

• Determinetheexactlocationoftheventhood.

• Plantherouteforventingexhausttotheoutdoors.

• Usetheshortestandstraightestductroutepossible.Forsatisfactoryperformanceductrunshouldnotexceed

100’equivalentlengthforanyductcongurations.

• 

Back to back elbows and “S“ turns give very poor delivery and are not recommended.

• A short straight length of duct at the inlet of the remote blower gives the best delivery.

• Referto“DuctFittings”charttocomputethemaximumpermissiblelengthforductrunstotheoutdoors.

• Installawallcapwithdamperorroofcapattheexterioropening.Orderthewallorroofcapandanytransition

needed in advance.

• Use 8" round metal ductwork only.

Wall framing for adequate support

• This vent hood is heavy. Adequate structure and support must be provided in all types of installations. If

mountedondrywall,thehoodmustbesecuretoverticalstudsinthewall,ortoahorizontalsupport.

• Theventhoodshouldbeonsitebeforenalframingandwallnishing.Thiswillhelptoaccuratelylocatethe

duct work and electrical service.

• Installation will be easier if the vent hood is installed before the cook-top and countertop are installed.

Removing the packaging

CAUTION:Removetthecartoncarefully.Wearglovestoprotectagainstsharpedges.

WARNING:Removetheprotectivelmcoveringtheproductbeforeputtingintooperation.

23

3

/32”

18”

30“

36“

12

1

/64”

18”

9

CHECK INSTALLATION HARDWARE

6 Screws 5 x 35

4 assembly screws for transition

Locate the hardware accesories box packed

with the hood

Pliers

Duct tape

Safety glasses

Masking tape

2 Hooks with regulating screw

4 Washers

Measuring tape

Knife

Wire cutter/stripper

Spirit level

Gloves

Strain relief

8?round metal duct,

length to suit installation

Saw, jig saw or

reciprocating saw

Hammer

Screwdrivers:

Phillips (Posidrive) # 2

Torx # 2

Wire nuts

Electric drill with

5/16” and 3/8” Bits

TOOLS REQUIRED FOR INSTALATION

List of Materials

Parts included in your hood

•Hood Canopy Assembly with blower, grease

ltersandlampsalreadyinstalled

• Care & Use /Installation Instructions

• Transition

•Fittingsbagwith:

 4Washers

 2 Hooks with regulating screws

6 Screws 5X35

4 screws for transition

•2greaselters(30")or3greaselters(36")

Parts Not Included with your Hood

• Duct Tape

• 1/2" Conduit

• Wire Nuts

•RoundorRectangularDuct.

•Roundbackdraftdamper

• Wiring clamp

• Wall fastener anchors

(foroptionalinstallationtoconcrete/masonrywalls.)

Optional accessories

• Duct covers

• Ductless recirculation kit

Materials required

• Duct tape

• Wire nuts

• Tape to mount template

• 8"roundedmetalduct(lenghttosuitinstallation)

Page is loading ...

11

Installation instructions

Typical installation

Theventhoodmustbeinstalledabovethecookingsurfaceat30"(minimum)ifagasrangeisusedorfrom24"

(minimum)to30"ifanelectricrangeisused.

The hood may be installed onto a wall and vented to the outdoors, or it can be installed for recirculating operation

(recirculatingaccessoriesnotsuppliedwiththehood).

This hood must not be installed over any professional cooktop / range.

1. Choosing the vent options

The hood design is ready to be used for vertical discharge as shown below.

Ifdesired,thehoodcanbeconvertedforhorizontaldischargeasshownbelow.

DUCTING

ProvideaRoundDucthavingadiameterof8”,refertoductttings

Installa1/2”conduitfromtheservicepanellongenoughtoreachthehoodonceitisinstalled.

Powersupplymustberatedfor120VAC,60Hz.15or20A.

Filter

Round Duct

Sot

Blower

Lamp

Transition

Hood

Horizontal discharge

30” min Gas Cooktop

24” min Electric Cooktop

30” min Gas Cooktop

24” min Electric Cooktop

30” min Gas Cooktop

24” min Electric Cooktop

Hood

Lamp

Sot

*Deector

Blower

Filter

* Charcoal lters

* Optional accessory - Ductless recirculation kit

Vertical discharge with recirculation

option

Round Duct

Sot

Transition

Filter

Blower

Lamp

Hood

Vertical discharge with vented option

Examples of possible ducting

INSTALLING THE HOOD

• Determinetheexactlocationoftheventhood.

• Forthemostefcientairowexhaust,useastraightrunorasfewelbowsaspossible.

CAUTION: Ventunittooutsideofbuilding,only.

Installation steps:

The following installation steps are required for wall mount installation or alternative cabinet installation.

12

Install framing for hood support

Warning: This installation instruction is not prepared for

horizontaldischarge

• If drywall is present, mark the screw hole locations.

Refertoductworkinstallationguidelines.

• Cutawayenoughdrywalltoexpose2verticalstudsat

the holes location indicated by the template.

 Install three horizontal supports at least 4" X 2"

between three wall studs at the bottom mounting holes

installation location.

• The horizontalsupport must be ushwith the room

side of the studs.

Use cleats behind both sides of the support to secure

to wall studs.

• Reinstalldrywallandrenish.

IMPORTANT

Framing must be capable of supporting 323 lbs.

Installation Instructions

8-1/2“ min. opening for ductwork

4“x 2“ Min. Mounting Support

Top screw location

Square slot

Bottom fixing screw location

Top outlet

Knockouts (junction box)

Side slot (4)

Rear outlet

13

Installation Instructions

DUCTWORK INSTALLATION GUIDELINES

2.Prepareductworkcutouts.Refertopicturesbelow.

12

5

/8“ 12

5

/8“

10“

12

5

/8“12

5

/8“

10 “

7/16“

8

13

/16“

10”

36”

4

15

/16”

2

1

/ 2”

1

39

/ 64”

12”

10

33

/ 64”

1

47

/ 64”

30”

10”

4

15

/16”

2

1

/ 2”

1

39

/ 64”

12”

10

33

/ 64”

1

47

/ 64”

36”

1

39

/ 64”

12”

10

33

/ 64”

1

47

/ 64”

30”

1

39

/ 64”

12”

10

33

/ 64”

1

47

/ 64”

φ 8

1

/4“

VERTICALDISCHARGE

HORIZONTALDISCHARGE

14

Installation Instructions

Discharge Direction:

WARNING!

Before installing remove the knock-out plate that close the air outlet on the top if is

desiredtousetherangehoodforverticaldischargeORtherearoutletifisdesiredto

usetherangehoodforhorizontaldischarge.(seealsoFigurebelow).

WARNING!

ONCE THE KNOCK OUT PLATE HAS BEEN REMOVED, THIS CANNOT BE REINSTALLED ANYMORE

TO CLOSE THE AIR OUTLET

Tochangetohorizontaldischarge,dothefollowing(seealsoFigurebelow):

a.Removeknock-outplateontherearsideofthehood(seealsoFigurebelow)

b.Removeandkeepthe4screws(2perside)thatxblowerontopofthehoodandrelease

it from keyholes.

c.Rotatetheblower90°andcheckthatpinsonsideblowerxingbracketstintothepreinstallingholes.

d.Fixtheblowerontherearsidewiththesame4screws(seestepb).

3. Assembly of the 8” Transition:

The transition supplied with the hood mounts to the top or rear of the hood.

Note-CabinetinstallationwithverticaldischargeONLY:donotinstalltransitionuntilhoodhasbeenxedon

cabinet.

a. Place the transition piece over the hood

exhaustandsecurewith4screwsprovided(Figurebelow).

b. Duct tape connection between transition and hood.

VER T I C AL D I S CHAR G E

HORI ZON TAL D I SCHA R G E

Keyhole

Top screw location

Square slot

Bottom fixing screw location

Knockouts (junction box)

Vertical discharge Knockouts

15

Installation Instructions

Wall Mount Installation

WARNING - The following instructions are intended for drywall only, please note that when installing to concrete/masonry

additionalwallfasteneranchors(notprovided)shallbeused

Note:seebelowifcabinetinstallationispreferred

4.Afterthehoodinstallationheighthasbeendetermineddrawahorizontallineatadistanceabovethecooktopequaltothe

desiredhoodinstallationheightplus10”.

5.Findthecenterlineofthecooktop.Drawaverticallinealongthiscenterlineuptothehorizontallinedrawninstep1and

drawaverticallinerightandleftatadistanceof11-59/64"(for36"model)or8-15/16”(for30"model)todeterminethe

mounting location of the mounting hooks shipped with the hood.

6. Fit two mounting hooks on the wall to hang the hood through the provided slots

(2hooks+2screws5x35).

7.Run8”Duct,longenoughtoreachthetransitiononcethehoodhasbeeninstalledplus

11/2”inchtoconnectductwork.FixDucttotransitionwithscrewsandsealwithtape.

8.Remove1of2knockoutsandinstall1/2”conduitconnectorinj-box.

9. Hang the hood and adjust its position through the screws on the hooks.

10.Fixthehoodto4additionalpoint,2onupperside,2onlowerside(use4washers+4screws5x35.

Cabinet Installation:

4. Find the centerline of the cabinet bottom. Draw a line along this centerline from rear to front of the cabinet.

5.Drawtwolines,oneataKdistancefromthewall,theotheroneataZdistancefromthepreviousline.

Mark 4 points , two along each line at a distance of half W from the center line, to determine the screw locations.

6.Fit4screwsoncabinetbottomdonottightencompletelybutleaveaspaceofabout1/2”fromcabinetbottomsurface

and head screws.

7.Run8”Duct,longenoughtoreachthetransitiononcethehoodhasbeeninstalledplus11/2”inchforconnectductwork.

8.Remove1of2knockoutsandinstall1/2”conduitconnectorinj-box.

9. Hang the hood on screws through side slots provided on hood top.

Tighten the four screws.

Note:Ifpossiblexthehoodonthewallat4additionalpoint(2onupperside,2onlowerside).

10.From the inside of the cabinet attach the transition on upper outlet.

FixDucttotransitionandsealwithtape.

11 59/64“11 59/64“

10“

7/16“

8

13

/16“

W

Z

K

8 1/4“

18 “

8 15/16“8 15/16“

10“

7/16“

8

13

/16“

W

Z

K

8 1/4“

18 “

16

Making the electrical connections:

WARNING

Electrical Shock Hazard

Warning: Turn off power at the service panel before wiring this unit.

120 VAC, 15 or 20 Amp circuit required.

IF HOUSE WIRING IS NOT A 3 WIRE INSTALLATION (NEUTRAL, LINE AND GROUND), A GROUND MUST BE PRO

-

VIDED BY THE INSTALLER. WHEN HOUSE WIRING IS ALUMINUM, BE SURE TO USE U.L. APPROVED ANTI-OXI

-

DANT COMPOUND AND ALUMINUM-TO-COPPER CONNECTORS.

ELECTRICAL GROUNDING INSTRUCTIONS. THIS APPLIANCE IS FITTED WITH AN ELECTRICAL JUNCTION BOX

WITH 3 WIRES, ONE OF WHICH (GREEN/YELLOW) SERVES TO GROUND THE APPLIANCE. TO PROTECT YOU

AGAINST ELECTRIC SHOCK, THE GREEN AND YELLOW WIRE MUST BE CONNECTED TO THE GROUNDING

WIRE IN YOUR HOME ELECTRICAL SYSTEM, AND IT MUST UNDER NO CIRCUMSTANCES BE CUT OR REMOVED.

Failure to do so can result in death or electrical shock.

•Removethej-boxcoverasshowninbelowpicture.

•Ifnotalreadydone,install1/2”conduitconnectorinj-box.

•Runblack,white,andgreenwires(#14AWG)accordingtotheNationalElectricalCodeorCSAStandardsandlocal

codes and ordinances.

•Connectblack,white,andgreenwiresfrompowersupplytoblack,white,andgreen/yellowwiresinj-boxrespectively.

•Closej-boxcover.

Power supply conduit

Junction box

Connecting the ductwork

• Installductwork,makingconnectionsinthedirectionofairowasillustrated.

• Pushductovertheexhaustoutlet.

• Wrapallductjointsandtheangeconnectionswithducttapeforanairtightseal.

• Makethesameconnectioninthewallorceilingventexit.

Final installation steps

• InstallgreaseltersasdescribedintheUse&Caresectionofthismanual.

•

Turn power on at service panel.

• Check operation of the hood.

 

 



Installation Instructions

17

Use And Care Instructions

Use and Care Instructions

Before using your hood read this manual carefully. The information on the following pages will help you operate

andmaintainyourhoodproperly.Keepithandytoansweryourquestions.

Ifyoureceiveadamagedhoodcontactimmediatelyyourdealer(builder)thatsoldyouthehood.

To obtain service, see the consumer service pages in the back of this manual. First contact the people who serviced

yourappliance,explainwhyyouarenotpleased.Inmostcases,thiswillsolvetheproblem.Ifarenotpleased,refer

to the warranty page and write all the details including your phone number.

1 Control Panel

2 Cover Lamp / Incandescent lamp

3 Grease Filter

18

Use And Care Instructions

Control and features

This hood is equipped with an electronic motor and lamp control. The control is able to set 3 different fan speeds,

turn ON/OFF light and has a timer function. In the following drawing are described the main key functions.

h4)-%2h+%9

hh+%9

h,)'(4h+%9

hh+%9

$)30,!9

#HARCOAL'REASEFILTER

1 2 3

#HARCOAL'REASEFILTER

1 2 3

hh+%9

h4)-%2h+%9

h,)'(4h+%9

$)30,!9

1. Timer Key

o The default timer setting is 10 minutes, and it can be adjusted between 20 minutes and 1

minute.

o After pressing the timer key, the control enters to a timer setup mode, and user can adjust the

timercountdowntimewiththe“-”and“+”keyswithin5seconds.Thetimercanbeinitiated

immediately pressing the timer key, after setting the timer duration or pressing the timer key

twice(default10minutessetting).

o If not action occurs within 5 seconds the countdown will start.

o Duringthetimersetupthe“-”and“+”keysarededicatedtothetimerandnomotoractionwill

occur.

o Once initiated the timer, it can be cancelled by pressing the timer key again.

2. Light Key

o PresslampkeytoturnONthelight(LampstatepreviouslyOFF).

o PresslampkeytoturnOFFthelight(LampstatepreviouslyON).

3. Display

Shows the hood settings.

4. “-” Key. Speed Decrease / OFF

o This key is used to decrease the fan speed, or turn OFF the fan.

o ThefanwillturnOFFifthe“-”keyispressedandthehoodwasintherstspeed.

o Ifthefanisatsecondspeedandthe“-”keyispressed,thefanwillbesettorstspeed.

o Ifthefanisatthirdspeedandthe“-”keyispressed,thefanwillbesettosecondspeed.

o IfthefanisOFFandthe“-”keyispressed,thecontrolbacklightwilllightup.

5. “+” Key. Speed Increase / ON

o This key is used to increase the fan speed, or turn ON the fan.

o ThefanwillturnONifthe“+”keyispressedandthehoodwasOFF.

o Ifthefanisatrstspeedandthe“+”keyispressed,thefanwillbesettosecondspeed.

o Ifthefanisatsecondspeedandthe“+”keyispressed,thefanwillbesettothirdspeed.

o Ifthefanisatthirdspeedandthe“+”keyispressed,abeepwillsound.

19

Use And Care Instructions

SPECIAL FUNCTIONS

Clock programming

• Theclockcanbereprogrammedatanytimeexceptduringanactivetimedfunction.

• Theclockcanbedisplayedinatwelvehourformatandvalidclocktimesarefrom1:00to12:59.

• Theclockcanbereprogrammedpressingthe“Timer”keyfor5seconds,andafter,theclockcanbeadjusted

withthe“+”and“-”keys.Colon“:”willashindicatingclockprogrammingmode.

• Theusercanhaveminuteincrements/decrementsof1minute,butiftheuserkeeppressingthe“+”/”-”keys

for more than 1 second, the increments / decrements will be of 5 minutes. During this option the control will

round to the nearest 5 minutes.

• Theusercannishonreprogrammingtheclockpressingthe“timer”key.

• After 1 minute of no key pressed the control will accept the programmed clock time and will add one minute

to the set clock.

Grease lter saturation alarm

• Afterthirtyfanfunctionalhours,thedisplaywillshow“GreaseFilter”ifthefanisactive.Whenthisiconis

showninthedisplay,thegreaseltersinstalledarerequiredtobewashed.

• Toresetthegreaseltersaturationalarmtheusermustpressthe“+”keyfor5seconds,afterthisactionthe

icon“greaselter”isnotdisplay,andthehoodhasthenormaldisplayoperation.

Charcoal lter saturation alarm (Recirculating accessories)

• Afteronehundredandtwentyfunctionalhoursofthefan,thedisplaywillshow“CharcoalFilter”ifthefan

isactive. Whenthisicon asheson display,the charcoallters installedarerequired tobe replaced or

reactivated.

• Toresetthegreaseltersaturationindicationtheusermustpressthe“-”keyfor5seconds,afterthistime

theicon“charcoallter”isnotdisplayandthehoodhasthenormaldisplayoperation.

Audible signal activation and deactivation

• Theaudiblesignalscanbeactivatedordeactivatedpressingthe“Light”keyfor5seconds.

• Iftheaudiblesignalisactivated,atonemustsoundandthe“Snd”symbolmustappearonthedisplayfor2

second.

• Iftheaudiblesignalisdeactivated,the“Snd”symbolmustappearonthedisplayfor2secondandnosound

must sound.

Charcoal lter inclusion and exclusion (Recirculating accessories)

• Thecharcoallterinclusionorexclusioncanbesetbypressingthe“-”and“+”keysatthesametimefor5

seconds.

• TheInclusionorexclusionofcharcoalltermustbeselectedwhilethelampsandthemotorareOFF.

• Whenthecharcoalhasbeenexcluded,thecharcoallteralarmisdisabled.

Heat sensor

• Thecontrolisequippedwithaheatsensorthatwillturnonthebloweratsecondspeedifexcessiveheat

occurs(over70°C)surroundingthecontrolarea.

• IftheblowerisOFForifitisoperatingatrstspeed,theblowerwillbesetautomaticallytosecondspeed.

• During this state, the user may raise the blower speed to third speed but can not decrease the speed.

• Whenthetemperaturelevelonthehooddropstonormal,theblowerwilloperateinthesettingdenedby

the user before the alarm occured.

20

Use And Care Instructions

Metal grease lter maintenance

Themetalltertrapsgreasereleasedbyfoodsonthecooktop.Theltermustalwaysbeinstalledwhenthehoodis

operating / used.

To remove:

• Pushthelterlock/pivotindirectiontothecenterofthelter.

• Oncethepivotispushedpulldownthelterslowly.

To replace:

• Inserttheltertabsintotheslots

• Pushthelterlock/pivotindirectiontothecenterofthelter.

• Oncethepivotispushed,raisethelterslowlyuntilthetopand

release the pivot.

To clean:

• Swishthelterinhotsoapywaterandrinseinclean

water or wash it in the dish washer.

• Do not use abrasive cleaners.

Hood maintenance

• Clean with a damp, soapy cloth and dry with a clean cloth. A glass

cleaner may also be used.

ATTENTION: Do not wet the control panel.

• Do not use a steel wool pad; it will scratch the surface.

• To clean the stainless steel surface, use warm sudsy water, stainless

steel cleaner or polish. Always wipe the surface in the direction of the

grain. Follow the cleaner instructions for cleaning the stainless

steel surface.

Lamp bulb maintenance

• UseaPhillips#2screwdrivertoremovethelamp

cover.Removeitcarefullyfromitshousing.

• Removethedamagedlampbulb(turncounter

clockwise)andreplaceitwithanewbulb.E12

PhilipsLamp120V,40W.

2

1

3

21

Available Accessories

Charcoal lter placement (Recirculating accessories)

Fitthecharcoalltermattressontheuppersideofeachgreaselter.

Useprovidedspringstoxitinplace.

Note:

When removing for replacing for a new one do not remove Fixing Springs, simply pull out one rotating

outwards.

Non-return valve installation (Recirculating accessories)

• Insertend"a"oftherodintothe"plastictransitiontube",pushingoutwardsuntilitcrossesthematerial(plastic

transitiontube)withalittleforce.

• Placeend"b"oftherodintothe"plastictransitiontube".Pushoutwardsuntilitcrossesthematerial(plastictransition

tube)withalittleforce,therodmustbesymetricallyfrombothsides.

• With the pliers bend both ends of the rod, towards the "plastic transition tube".





�



















Page is loading ...

arietta PRO001MX 30 Installation guide

This manual is also suitable for

arietta PRO001MX 30 Installation guide

in other languages

Related papers

Other documents