Extron ISM 1WB User manual

ISM 1WB
Extron
Brand
Extron
Model
ISM 1WB
Type
User manual

This manual is also suitable for

ISM 1WB and 2WB Output Board • Setup Guide
The Extron
®
ISM 1WB (single output)
and ISM 2WB (dual output) are
wideband output boards for
the ISM 824. Both boards pass
signals through unprocessed
on either BNCs (ISM 1WB) or
dual 15-pin HD connectors (ISM 2WB). Both boards have
local audio output(s). The ISM 1WB and ISM 2WB boards
are mounted at the rear of the ISM 824, in the vertical
expansion slots. The ISM 1WB board can be mounted in
any of the four slots (numbered 1 to 4). The ISM 2WB
must be mounted in slots 1 and 2 (dual output slots). Refer to the ISM 824 User Guide,
online at www.extron.com for operating details.
To install an ISM 1WB or ISM 2WB output board in the ISM 824 unit,
1. Turn off the ISM 824. Remove the power cord. Repeat for all connected devices.
2. Select an open slot at the rear, or take out a blank plate by removing the two screws
(top and bottom), and lifting the plate away.
NOTE: Retain and re-use the screws to secure the new output board in place. Retain
the blank plates. If a board is installed in the desired slot, remove the screws
and carefully pull out the board.
3. Holding it by the frame, align the front
(non-connector end) of the board with the top
and bottom plastic guides in the ISM 824. Slide
the board in carefully, keeping within the guides.
Push it into place firmly, and secure it with the
retained screws.
4. If required, repeat steps 2 through 4.
5. Power on the ISM 824. The new output board(s)
is auto-detected, and takes approximately 30
seconds to initialize. The 16 character LCD display
indicates the new board type, slot used, and
counts down the initialization time. See inset for
example display for a new ISM 1WB board installed in slot #2,
with 7 seconds left.
6. Following the image at right, connect output device
cables to the BNC connectors to output RGBHV, RGBS,
RGsB, or HD component video signals. If using an ISM 2WB,
connect a suitable RGB display to the 15-pin HD connectors.
7. Insert a 5-pole captive screw connector into the local audio
output connector for balanced or unbalanced stereo audio
output. Wire the connector as shown below.
1
100
-
240
50/60 Hz
1.2A MAX.
1
2 3 4 5 6 7 8
2
1 2
3 4 5 6 7 8
1
2
1
INPUTS
OUTPUTS
R/R-Y
G/Y
VID
B/C
B-Y
H/HV
V
R/R-Y
G/Y
VID
B/C
B-Y
H/HV
V
PASS THRU
INPUTS
RESET
LAN
REMOTE
RS232/RS422
ACT
LINK
OUTPUT
VIDEO
SCALER
70-545-01
3
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
UNIV.
SCALER
70-544-01
5
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
PASS
THRU
70-547-01
8
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
Extron
ISM 824
Integration Scaling
Matrix Switcher
Align output board
with top and bottom
plastic guides.
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
7
SCAN
CONV.
70-546-01
Example Output Board Installation
New Wideband
Slot #2 07
RGB/R-Y,Y,B-Y
/YC/VID
OUTPUT
3 / 5
OUTPUT
4 / 6
RGB/R-Y,Y,B-Y
/YC/VID
L
R
L
R
DUAL
WIDEBAND
ISM 2WB
ISM 1WB
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
L
R
WIDEBAND
H/
HV
RGBHV
Video
RGsB or
Component
Video
RGBS
Video
V
H/
HV
V
H/
HV
V
R/
R-Y
G/Y
B/
B-Y
R/
R-Y
G/Y
B/
B-Y
R/
R-Y
G/Y
B/
B-Y
CAUTION: For unbalanced audio, DO NOT connect the sleeves to the negative
contacts. Connect to the center ground contact.
Unbalanced Stereo Output
Balanced Stereo Output
Tip
Ring
Sleeve(s)
Tip
Ring
L R
Left
Right
Tip
Sleeve(s)
Tip
L R
Left
Right
NO GROUND HERE.
NO GROUND HERE.
Extron USA - West
Headquarters
+800.633.9 876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9 876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FA X
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.404 0
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.88 3.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299180 0
+971.4.299188 0 FA X
68-1123-66
Rev A
08 10
© 2010 Extron Electronics. All rights reserved. www.extron.com
ISM 1WB and 2WB Output Board • Setup Guide, cont’d
2
Command ASCII comm
(host to ISM)
Response
(ISM to host)
Additional description
Input selection
Video and audio
X!*X@! OutX@•InX!•All
]
Tie video/audio input X! to X@.
Video
X!*X@& OutX@•InX!•RGB
]
Tie video input X! to output X@.
Audio
X!*X@$ OutX@•InX!•Aud
]
Tie audio input X! to output X@.
Volume control
Set volume
X@*X3$V
OutX@•Vol
X3$]
Set volume to
X3$
for output
X@
.
Increment
X@+V
OutX@•Vol
X3$]
Increase volume.
Decrement
X@-V
OutX@•Vol
X3$]
Decrease volume.
View X@V
X3$]
View current volume setting.
Audio gain and attenuation
Specific gain
X!*X3@G
In
X!•
Aud
X3!]
Set input
X!
gain to
X3!
.
Set attenuation
X!*X3#g
In
X!•
Aud
X3!]
Set input
X!
attenuation to
X3#
.
Increment
X!+G/g
In
X!•
Aud
X3!]
Raise input
X!
audio level to
X3!
.
Decrement
X!-G/g
In
X!•
Aud
X3!]
Lower input
X!
audio level to
X3!
.
View
X!G/g
X3!]
View audio level of input
X!.
RGB Delay
Delay on
3*X@*X3&#
X@
Dly
X3&]
Set RGB delay.
View setting
3*X@#
X3&]
View RGB delay setting.
Video mute
Mute on
X@*1B X@
Vmt
1]
Mute selected video output.
Mute off
X@*0B X@
Vmt0
]
Unmute selected video output.
View X@B
X1)]
View the mute status.
Audio mute
Mute on
X@*1Z X@
Amt
1]
Mute selected audio output.
Mute off
X@*0Z X@
Amt
0]
Unmute selected audio output.
View X@Z
X1)]
View mute status.
Board-specific SIS commands
Specific SIS commands can be used with the ISM 1WB and ISM 2WB boards.
Refer to the ISM 824 User Guide at www.extron.com, for a detailed command list.
NOTE: X! = Input number, 0-8
X@ = Output number, 1-8
X1) = Mode status, 1 = on, 0 = off
X3!
= Audio level adjustment range (-18 to +24)
X3@
= Audio gain adjustment range (0 to 24)
X3# = Audio attenuation adjustment range (18 to 0)
X3$ = Volume adjustment range (0 - 64)
X3&
= RGB delay duration 00 to 50 in 0.1 second increments (0.0 second to 5.0 seconds)
  • Page 1 1
  • Page 2 2

Extron ISM 1WB User manual

ISM 1WB
Extron
Brand
Extron
Model
ISM 1WB
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents