Extron ISM DVI User manual

Extron
Brand
Extron
Model
ISM DVI
Category
Socket-outlets
Type
User manual
The Extron
®
ISM DVI is a
universal video and RGB
scaler board with DVI
output, for use with the
ISM 824. It also has a DVI
connector and a local audio output. The board mounts in one of the four vertical
expansion slots (numbered 1 to 4) at the rear of the ISM 824.
Refer to the ISM 824 User Guide, online at www.extron.com for operating details.
To install an ISM DVI output board in the ISM 824 base unit:
1. Turn off the ISM 824. Remove the power cord. Repeat for all connected devices.
2. Select an open slot at the rear, or take out a blank plate by removing the two
retaining screws (top and bottom), and lifting the plate away.
NOTE: Retain and re-use the screws to secure the new output board in place.
Retain the blank plates. If a board is already installed in the desired slot,
remove the screws and carefully pull out the board.
3. Holding the new board by the frame,
align the front (non-connector end) of the
board with the top and bottom plastic
guides in the ISM 824. Slide the board in
carefully, keeping within the guides. Push
it into place firmly, and secure it with the
retained screws.
4. If required, repeat steps 2 through 4
for any other output boards.
5. Power on the ISM 824. The new output
board(s) is autodetected, and takes
approximately 30 seconds to initialize.
The 16 character LCD display indicates the new board type, slot used, and counts
down the initialization time.
See inset for example display of a new ISM DVI board
installed in slot #3, with 8 seconds left.
6. Connect a suitable display device to the DVI connector. The output can be
configured via the front panel (see page 2) or by SIS
™
commands (see page 3).
7. Insert a 5-pole captive screw connector into the local audio output connector
for balanced or unbalanced stereo output. Wire the connector as shown below.
1
100
-
240
50/60 Hz
1.2A MAX.
1
2 3 4 5 6 7
8
2
1 2
3 4 5 6 7 8
1
2
1
INPUTS
OUTPUTS
R/R-Y
G/Y
VID
B/C
B-Y
H/HV
V
R/R-Y
G/Y
VID
B/C
B-Y
H/HV
V
PASS THRU
INPUTS
RESET
LAN
REMOTE
RS232/RS422
ACT
LINK
OUTPUT
VIDEO
SCALER
70-545-01
3
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
UNIV.
SCALER
70-544-01
5
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
PASS
THRU
70-547-01
8
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
Extron
ISM 824
Integration Scaling
Matrix Switcher
Align output board
with top and bottom
plastic guides.
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
7
SCAN
CONV.
70-546-01
Example Output Board Installation
New Univ DVI
Slot #3 08
ISM DVI
DVI
UNIVERSAL
SCALER
DVI-D
L
R
ISM DVI Output Board • Setup Guide
Unbalanced Stereo Output
Balanced Stereo Output
Tip
Ring
Sleeve(s)
Tip
Ring
L R
Left
Right
Tip
Sleeve(s)
Tip
L R
Left
Right
NO GROUND HERE.
NO GROUND HERE.
CAUTION: For unbalanced audio, DO NOT connect the sleeves to the
negative contacts. Connect to center ground contact.
ISM DVI Output Board • Setup Guide, cont’d
ISM DVI configuration menu
Using the front panel menu buttons (Menu and Next), the ISM DVI configuration
menu can be accessed. From the Output Configuration screen, press Next until
reaching the #x Univ DVI menu (see the image below). Press Menu and Next to
navigate through the menus and use the front panel adjust knobs ({ [), to
change the settings as desired. For full menu details see the ISM 824 User’s
Manual, online at www.extron.com.
From the default cycle press Menu repeatedly to reach the Output
Configuration menu. Press Next (enters Select Output menu) and rotate
either Adjust knob to select the Univ DVI menu. Follow the figure below
to enter each menu and use the Adjust knobs to change value as desired.
Selec t Out put
#7 U niv DVI
Next
Input Setu p
#7 U niv DVI
Aspec t Rat io
4:3
Next
Rotate either encoder
to select Aspect Ratio
(4:3 or 16:9)
Next
H Start V
128 1 28
Rotate encoder to
adjust H(orizontal) start
Rotate encoder to
adjust V(ertical) start
Next
Total Pix Phase
1728 0 0
Rotate encoder to
adjust Total Pix value
Rotate encoder to
adjust Phase value
Next
H Activ e V
1283 10 28
Rotate encoder to
adjust H active value
Rotate encoder to
adjust V active value
Menu
Next
Outpu t Con fig
#7 U niv DVI
Rotate encoder
to adjust resolution
Rotate encoder
to adjust refresh rate
Next
1024x 768 6 0
Resol ution
Next
Menu
User Prese ts
#7 U niv DVI
<NA> 1 2 3
Save Pr eset
Next
Rotate either encoder
to select a preset to
save current settings
<NA> 1 2 3
Erase Pres et
Next
Rotate either encoder
to select a preset
to erase
Advanced Confi g
#7 U niv DVI
Next
None
Te st Patter n
Rotate either encoder
to select a test pattern
<Off> On
Blue Mode
Next
Rotate either encoder
to turn blue mode On
or Off
Off <On>
Film Mode
Next
Rotate either encoder
to turn film mode On
or Off
Next
Menu
Next
Next
Rotate encoder to
select input
Rotate encoder to
turn On or Off
Input #2 Off
Auto I mag e
Auto Memo ries
Next
Rotate either encoder
to turn auto memories
On or Off
Off <On>
Next
Input #2 O ff
Full Scree n
Rotate encoder to
select input
Rotate encoder to
turn On or Off
NOTE: Within any submenu, press the Menu button
to go directly to the top level (Output Card
Configuration) menu. If, for 30 seconds, no
button is pressed or adjust knob is rotated,
the menu times out and reverts to the default
display cycle.
Input Setup
The Input Setup submenu allows configuration of aspect ratio, horizontal and
vertical start points, total pixels, phase value, horizontal and vertical area. Rotate
the Adjust knobs as required to change values.
MENU NEXT
ADJUST
2
Output Config
The Output Config submenu displays and allows changes to be made to the
resolution and refresh rate. Use the adjust knobs to select a resolution and
refresh rate.
Resolution 24 Hz 25 Hz 30 Hz 50 Hz 60 Hz 72 Hz 75 Hz 59.94 Hz
640x480 X X X
800x600 X X X
852x480 X X X
1024x768 X X X
1024x852 X X X
1024x1024 X X X
1280x768 X X X
1280x800 X X
1280x1024 X X X
1360x765 X X X
1365x768 X X X
1366x768 X X X
1365x1024 X X X
1400x1050 X X
1440x900 X X
1600x1200 X X
1680x1050 X
1920x1200 X
480p X X
576p X
720p X X X
1080i X X X
1080p X X X X X X
1080p Sharp X
User Presets
The User Preset submenu displays and allows the current settings to be saved
as a preset, or to erase an existing saved preset. Use the Adjust knobs to select
between the presets.
Advanced Config
Within this submenu the following settings can be adjusted: auto Image (turn on
or off), test pattern (selection), blue mode (on or off), auto memories (on or off),
film mode (on or off), and full screen (on or off).
Test pattern
The test pattern submenu offers the following test patterns to choose from: split
color bars, two crosshatch patterns, grayscale, ramp, alternating pixels, crop, and
four aspect ratio patterns.
3
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.466 4 FA X
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.29 91800
+971.4.29 91880 FAX
68-1123-64
Rev A
08 10
© 2010 Extron Electronics. All rights reserved. www.extron.com
4
Board-specific SIS commands table
The ISM DVI board can be configured with specific Special Instruction Set
™
(SIS)
commands. The table below lists some of the ISM DVI board-specific commands.
For a full list refer to the ISM 824 User Guide, online at www.extron.com.
Command ASCII
command
(host to ISM)
Response
(ISM to host)
Additional description
Input selection
Video and audio
X!*X@! OutX@•InX!•All
]
Tie video/audio input X! to X@.
Video
X!*X@& OutX@•InX!•RGB
]
Tie video input X! to output X@.
Audio
X!*X@$ OutX@•InX!•Aud
]
Tie audio input X! to output X@.
Output scaler rate
Set output rate
X@
*
X2!
*
X2@
= RteX@ *X2!*X2@
]
Set output resolution/refresh rate
View
X@
= X2!*X2@
]
View selected output rate
Start auto image
Start auto image
14*X@#
ImgX@
]
Auto image input tied to X@.
Auto memory
On
X@*1M X@
Aut1
]
Set auto memory to on.
Off
X@*0M X@
Aut0
]
Set auto memory to off.
View setting
X@M
X1)]
View current auto memory.
Auto image
Enable
55*X@* X!*1# X@ImgX!*1
]
Enables auto image for all inputs.
Disable
55*X@* X!*0# X@ImgX!*0
]
Disables auto image.
View
55*X@* X!#
X1)
]
View auto image on/off setting.
Input aspect ratio
16:9
9*X@*1# X@AspX!*1
]
Set input aspect ratio 16:9
.
4:3
9*X@*0# X@AspX!*0
]
Set input aspect ratio 4:3
.
View
9*X@#
X5%
]
View current aspect ratio.
Full screen
Enable
99*X@*X!*1# X@FulX!*1
]
Enable full screen display.
Disable
99*X@*X!*0# X@FulX!*0
]
Disable full screen display.
View
99*X@*X!#
X1)
]
View the full screen status.
NOTE: X! = Input number, 0-8
X@
= Output number, 1-8
X1)
= Mode status, 1 = on, 0 = off
X2!
= Output resolution, 01 = 640x480, 02 = 800x600, 03 = 852x480, 04 = 1024x768,
05 = 1024x852, 06 = 1024x1024, 07 = 1280x768, 08 = 1280x1024, 09 = 1360x765,
10 = 1365x768, 11 = 1366x768, 12 = 1365x1024, 13 = 1400x1050, 14 = 1600x1200,
15 = 480p, 16 = 576p, 17 = 720p, 18 = 1080i, 19 = 1080p, 20 = 1280x800,
21 = 1440x900, 22 = 1680x1050, 23 = 1920x1200, 24 = 1080pSharp
X2@
= Output refresh rate, 1 = 50 Hz, 2 = 60 Hz, 3 = 72 Hz, 7 = 24 Hz, 8 = 25 Hz,
9 = 30 Hz, 10 = 59.94 Hz, 11 =75 Hz
X5%
= Aspect ratio, 1 = 16:9, 0 = 4:3
ISM DVI Output • Board Setup Guide, cont’d
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Extron ISM DVI User manual

Extron
Brand
Extron
Model
ISM DVI
Category
Socket-outlets
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents