Extron ISM V User manual

Extron
Brand
Extron
Model
ISM V
Type
User manual
The Extron
®
ISM VS is a video
scaler board for the ISM 824,
and outputs scaled low
resolution (composite, S-video,
and YUVi) signals and passes through RGB and HD component signals. It has
5 female BNC connectors and a local audio output. The board mounts in one of the
four vertical expansion slots (numbered 1 to 4) at the rear of the ISM 824.
Refer to the ISM 824 User Guide, available at www.extron.com.
To install an ISM VS output board in the ISM 824 base unit:
1. Turn off the ISM 824. Remove the power cord. Repeat for all connected devices.
2. Select an open slot at the rear, or take out a blank plate by removing the two
retaining screws (top and bottom), and lifting the plate away.
NOTE: Retain and re-use the screws to secure the new output board in place.
Retain the blank plates. If a board is already installed in the desired
slot, remove the screws and carefully pull out the board.
3. Holding the new board by the frame,
align the front (non-connector end) of the
board with the top and bottom plastic
guides in the ISM 824. Slide the board in
carefully, keeping within the guides. Push
it into place firmly, and secure it with the
retained screws.
4. If required, repeat steps 2 through 4
for any other output boards.
5. Power on the ISM 824. Any new output
boards are autodetected, and take
approximately 30 seconds to initialize. The 16 character LCD
display indicates the new board type, slot used, and counts
down the initialization
time. See inset for example display of a new ISM VS
board installed in slot #1, with 11 seconds left.
6. Following the image at right, connect output device
cables to the BNC connectors to output RGBHV, RGsB
video, RGsB, or HD component video signals. The output
can be configured from the front panel (see page 2) or
by SIS
™
commands (see pages 3 and 4).
7. Insert a 5-pole captive screw connector into the local
audio output connector for balanced or unbalanced
stereo audio output. Wire the connector as shown below.
1
100
-
240
50/60 Hz
1.2A MAX.
1
2 3 4 5 6
7 8
2
1 2
3 4 5 6 7 8
1
2
1
INPUTS
OUTPUTS
R/R-Y
G/Y
VID
B/C
B-Y
H/HV
V
R/R-Y
G/Y
VID
B/C
B-Y
H/HV
V
PASS THRU
INPUTS
RESET
LAN
REMOTE
RS232/RS422
ACT
LINK
OUTPUT
VIDEO
SCALER
70-545-01
3
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
UNIV.
SCALER
70-544-01
5
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
PASS
THRU
70-547-01
8
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
Extron
ISM 824
Integration Scaling
Matrix Switcher
Align output board
with top and bottom
plastic guides.
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
7
SCAN
CONV.
70-546-01
Example Output Board Installation
ISM VS Output Board Setup • Guide
New Video Scaler
Slot #1 11
H/HV
RGBHV
Video
RGsB or
Component
Video
RGBS
Video
V
H/HV
V
H/HV
V
R/R-Y
G/Y
VID
B/C
B-Y
R/R-Y
G/Y
VID
B/C
B-Y
R/R-Y
G/Y
VID
B/C
B-Y
Unbalanced Stereo Output
Balanced Stereo Output
Tip
Ring
Sleeve(s)
Tip
Ring
L R
Left
Right
Tip
Sleeve(s)
Tip
L R
Left
Right
NO GROUND HERE.
NO GROUND HERE.
CAUTION: For unbalanced audio, DO NOT connect the sleeves to the
negative contacts. Connect to center ground contact.
ISM VS
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
L
R
VIDEO
SCALER
ISM VS Output Board • Setup Guide, cont’d
ISM VS configuration menu
Using the front panel menu buttons (Menu and Next), the ISM VS configuration
menu can be accessed. From the Output Configuration screen, press Next until
reaching the #x Video Scaler menu (see the image below). Press Menu and Next
to navigate through the menus and use the front panel adjust knobs ({ [), to
change the settings as desired. Refer to the ISM 824 User Guide, online at
www.extron.com for full details.
From the default cycle press Menu repeatedly to reach the Output Configuration
menu. Press Next (enters Select Output menu) and rotate either Adjust
knob to select the Video Scaler menu. Follow the figure below to enter
each menu and use the Adjust knobs to change value as desired.
MENU NEXT
ADJUST
2
Select Ou tpu t
#3 Vid eo Scal er
Next
Menu
Output Co nfi g
#3 Vid eo Scal er
RGBHV
Output Ty pe
Rotate encoder to
adjust pixel value
Rotate encoder to
adjust refresh rate
Next
H - V -
Sync Polar ity
Next
Rotate either encoder
to change sync polarity
(H- V-, H- V+, H+ V-, H+ V+)
1024x768 60
Resolutio n
Next
Rotate either encoder
to select output type
(RGBHV, RGBS,
RGsB, YUV Bi-Level)
Next
Menu
Next
User Pres ets
#3 Vid eo Scal er
<NA> 1 2 3
Save Pre set
Next
Rotate either encoder
to select a preset to
save current settings
<NA> 1 2 3
Erase Pre set
Next
Rotate either encoder
to select a preset
to erase
Advance d C onfig
#3 Vid eo Scal er
Menu
Next
000 000
Top B lanking B ot
Next
<Off> O n
Blue Mode
Next
Off < On>
Filter
Next
Rotate either encoder
to turn encoder filter
On or Off
Off <On >
2:2 Pulld own
Next
Rotate either encoder
to turn 2:2 Pulldown
On or Off
<Off> O n
Enhanced Mod e
Next
Rotate either encoder
to turn enhanced mode
On or Off
Auto Me mories
Next
Rotate either encoder
to turn auto memories
On or Off
Off <On >
Rotate encoder to
select input
Rotate encoder to
turn On or Off
Input #2 On
Auto Image
Rotate either encoder
to turn Blue Mode
On or Off
NOTE:
Within any submenu, press the Menu button
to go directly to the top level (Output Card
Configuration) menu. If, for 30 seconds, no
button is pressed or adjust knob is rotated,
the menu times out and reverts to the default
display cycle.
Rotate encoder
to adjust top blanking
Rotate encoder to
adjust bottom blanking
Output Config
The Output Config submenu displays and allows changes to be made to the
resolution and refresh rate. Use the adjust knobs to select a resolution and
refresh rate.
Resolution 50 Hz 60 Hz
640x480 X X
800x600 X X
852x480 X X
1024x768 X X
1280x768 X X
1280x1024 X X
1360x765 X X
1365x768 X X
1366x768 X X
1365x1024 X X
1400x1050 X X
480p X
576p X
720p X X
1080i X X
1080p X X
User Presets
The User Preset submenu displays and allows the current settings to be saved as
a preset, or to erase an existing saved preset. Use the Adjust knobs to select the
presets.
Advanced Config
Within this submenu the following settings can be adjusted: auto image
(on or off), top and bottom blanking (set area), filter (on or off), blue mode
(on or off), auto memories (on or off), 2:2 pulldown (on or off), and enhanced
mode (on or off).
Board-specific SIS
™
commands
The ISM VS board can be configured with specific Special Instruction Set
™
(SIS)
commands. The table on page 4 lists some of the ISM VS board-specific
commands.
Refer to the ISM 824 User Guide, available online at www.extron.com for a full
list of definitions and commands.
3
SIS commands table and definitions are on page 4.
Extron USA - West
Headquarters
+800.633.9 876
Inside USA / Canada Only
+1.714.491.15 00
+1.714.491.1517 FAX
Extron USA - East
+800.633.9 876
Inside USA / Canada Only
+1.919.8 63.1794
+1.919.8 63.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.404 0
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.88 3.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299180 0
+971.4.299188 0 FA X
68-1123-63
Rev A
08 10
© 2010 Extron Electronics. All rights reserved. www.extron.com
4
ISM VS Output Board • Setup Guide, cont’d
NOTE: X! = Input number, 0-8
X@
= Output number, 1-8
X1)
= Mode status, 1 = on, 0 = off
X1%
= Picture adjustment (0 to 255)
X2!
= Output resolution, 01 = 640x480, 02 = 800x600, 03 = 852x480, 04 = 1024x768,
07 = 1280x768, 08 = 1280x1024, 09 = 1360x765, 10 = 1365x768, 11 = 1366x768,
12 = 1365x1024, 13 = 1400x1050, 15 = 480p, 16 = 576p, 17 = 720p,18 = 1080i,19 = 1080p
X2@
= Refresh rate, 1 = 50 Hz, 2 = 60 Hz
X2%
= User presets (1 to 3)
Board-specific SIS commands table
Command ASCII
command
(host to ISM)
Response
(ISM to host)
Additional description
Input selection
Video and audio
X!*X@! OutX@•InX!•All
]
Tie video/audio input X! to X@.
Video
X!*X@& OutX@•InX!•RGB
]
Tie video input X! to output X@.
Audio
X!*X@$ OutX@•InX!•Aud
]
Tie audio input X! to output X@.
Output scaler rate
Set output rate
X@
*
X2!
*
X2@
= RteX@ *X2!*X2@
]
Set output resolution/refresh rate
View
X@
= X2!*X2@
]
View resolution/refresh rate
User presets (1 to 3)
Recall preset
X@*X2%.
X@
Rpr
X2%]
Recalls user preset
X2%
.
Save preset
X@*X2%,
X@
Spr
X2%]
Saves user preset
X2%
.
Edge smoothing filter
Set filter on/off
16*X@*X1)# X@
Fil
X! *X1)]
Set filter on or off.
View setting
16*X@#
X1)]
View setting.
Enhancement mode
Set mode on/off
52*X@*X1)# X@
Ehn
X! *X1)]
Set enhancement mode on or off.
View setting
52*X@#
X1)]
View setting.
Top blanking
Specify a value
X@*X1% ( X@
Blt
X!*X1%]
Set number of top lines to blank.
Increment value
X@+( X@
Blt
X!*X1%]
Increase number of lines to blank.
Decrement value
X@-( X@
Blt
X!*X1%]
Decrease number of lines to blank.
View
X@(
X1%]
Show number of lines to blank.
Bottom blanking
Specify a value
X@*X1% ) X@
Blb
X!*X1%]
Set number of bottom lines to
blank.
Increment value
X@+) X@
Blb
X!*X1%]
Increase number of lines to blank.
Decrement value
X@-) X@
Blb
X!*X1%]
Decrease number of lines to blank.
View
X@)
X1%]
Show number of lines to blank.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Extron ISM V User manual

Extron
Brand
Extron
Model
ISM V
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents