Whirlpool AGB 433/WP User guide

Brand: Whirlpool

Model: AGB 433/WP

Type: User guide

019_03

Instructions for installation,

use and maintenance

07/2007

ELECTRIC FRYER

AGB 433/WP · AGB 437/WP

AGB 435/WP · AGB 439/WP

AGB 441/WP · AGB 445/WP

AGB 443/WP · AGB 447/WP

019

03 - Electric fryer

Models and dimensions page 3

Technical data 5

Installation instructions 6

Installation 6

Legal and technical requisites 6

Installation 6

Wiring 6

Unipotential 6

Using the appliance 7

Ignition 7

Emptying the bath 7

Cleaning and taking care of the

appliance 7

What to do if not using the appliance

for a long time 7

What to do if something goes wrong 7

Maintenance 7

WEEE Directive 8

Wiring diagrams 9-10

Warning 11

INDEX

019

03 - Electric fryer

Dimensions

Main switch

Pilot lamp (voltage)

Pilot lamp (resistance)

AGB 441/WP / AGB 443/WP

400 x 900x 270 / 530

Weight approx.59 kg / 62 kg

AGB 445/WP / AGB 447/WP

800 x 900x 270 / 530

Weight approx.109 kg / 120 kg

019

03 - Electric fryer

Dimensions

Main switch

Oil outlet drive

Pilot lamp (voltage)

Pilot lamp (resistance)

AGB 433/WP / AGB 435/WP

400 x 900x 875

Weight approx..70 kg / 73 kg

AGB 437/WP / AGB 439/WP

800 x 900x 875

Weight approx..120 kg / 131 kg

019

03 - Electric fryer

Technical data

The data plate is located on the rigth hand side of the

control panel and contains all the data needed for connecting

it up to the mains electricity supply.

TIPO/TYPE

CAT/KAT GAS/GAZ G30 G31 G20 G25

II2H3B/P P mbar 30 30 20 -

II2H3+ P mbar 30 37 20

II2H3+ P mbar 28 37 20 -

25II2L3B/P P mbar 30 30

II2ELL3B/P P mbar 50 50 20 20

II2E+3+ P mbar 28 37 20 -

II2H3B/P P mbar 50 50 20 -

I2E P mbar - - 20 -

--II2H3B/P P mbar 30 30

II2H3+ P mbar 28 37 20 -

I3B/P P mbar 30 30

I3+ P mbar 28 37

SE FI DK CZ SK SI

IT CH PT

ES IE GB GR

FR BE

AT CH

EE LV LT

NO MT CY IS HU

MOD.

ART.

Qn kW

MADE IN ITALY

Predisposto a gas: - Gas preset: - Prevu pour gaz:

Eingestelt für Gas: - Preparado para gas: -

Geschuckt voor:

V KW Hz

THE APPLIANCE MUST BE CONNECTED IN COMPLIANCE WITH THE LAWS IN FORCE

AND INSTALLED IN A WELL-VENTILATED ROOM. READ THE INSTRUCTION MANUALS

BEFORE INSTALLING AND USING THE APPLIANCE.

THE APPLIANCE MUST BE INSTALLED BY QUALIFIED PERSONNEL.

Model

AGB 433/WP

AGB 437/WP

AGB 435/WP

AGB 439/WP

AGB 441/WP

AGB 445/WP

AGB 443/WP

AGB 447/WP

FRYER

Dim.: LxWxH

400 x 900 x 875

600 x 900 x 875

400 x 900 x 875

800 x 900 x 875

400 x 900 x 875

800 x 900 x 875

400 x 900 x 270

600 x 900 x 270

400 x 900 x 270

800 x 900 x 270

400 x 900 x 530

800 x 900 x 530

Voltage rating

230 V 3 / 400 V 3N

Power

7.5 kW

15.0 kW

12.0 kW

24.0 kW

15.0 kW

30.0 kW

7.5 kW

15.0 kW

12.0 kW

24.0 kW

15.0 kW

30.0 kW

Lead wire / Section

4 x 2.5 mm

5 x 1.5 mm

4 x 6 mm

5 x 2.5 mm

4 x 6 mm

5 x 2.5 mm

4 x 10 mm

5 x 6 mm

4 x 6 mm

5 x 2.5 mm

4 x 10 mm

5 x 6 mm

4 x 2.5 mm

5 x 1.5 mm

4 x 6 mm

5 x 2.5 mm

4 x 6 mm

5 x 2.5 mm

4 x 10 mm

5 x 6 mm

4 x 6 mm

5 x 2.5 mm

4 x 10 mm

5 x 6 mm

019

03 - Electric fryer

Before beginning installation, remove all packaging from

the appliance. Some parts are protected with an adhesive

film which should be carefully removed.

Any remnants of glue should be thoroughly cleaned using

suitable substances such as benzine. Under no circum-

stances should abrasive substances be used.

Fit the legs to the appliance; the appliance must be level-

led using a spirit level. Slight irregularities can be levelled

by adjusting the feet themselves.

The main switch or plug should be located in the vicinity of

the appliance and easy of access. We recommend instal-

ling the machine under a range hood so that all the fumes

are removed as quickly as possible. If the appliance is to

be installed near walls, dividing walls, kitchen equipment

or decorative pannelling, these should be in non-inflam-

mable material or covered with non-inflammable material.

Make sure that all fire prevention standards and safety pre-

cautions are strictly adhered to.

Warning !

MODELS AGB 433/WP - AGB 435/WPif this model is

going to be mounted on its own, it must be fixed to the

floor.

Fixing accessories are included.

The appliance should be fitted following the indica-

tions given in the drawing below.

Legal and technical requisites

When installing the appliance, the following safety stan-

dards must be adhered to:

- Local accident prevention standards

- Current CEI standards.

Installation

Installation, start-up and maintenance should only be car-

ried out by expert personnel. All work required to install

the appliance should be carried out in compliance with all

local standards and regulations. The manufacturers decli-

ne all responsibility where poor performance is due to in-

correct installation in disregard of the above conditions.

Warning!

In compliance with international regulations, when

connecting the appliance to the mains power supply, a

device with a minimum aperture of 3 mm between con-

tacts must be fitted upstream of the appliance, al-

lowing omnipolar disconnection of the appliance from

the mains.

Wiring

When choosing the lead wire, make sure it has the fol-

lowing characteristics: it should be at least of the H07 RN-F

type and its section should be large enough for the ap-

pliance (see "Technical specifications and dimensions",

page 5).

Wire entry is underneath the appliance, on the left hand si-

de. The terminal board is at the front, behind the control

panel.

Pass the wire through the core hitch and wire clamp, plug

the leads into their terminals on the board and secure

them.

The earth lead must be a little longerthan the others so

that it is the last lead to disconnect if the wire clamp

breaks.

Unipotential

The appliance must be connected up to a unipotential sy-

stem. The connection screw is located underneath the ap-

pliance, on the right hand side. It is labelled.

Warning!

The manufacturers cannot be held responsible for any

damage due to inadequate or incorrect installation.

Under such circumstances the guarantee will be con-

sidered null and void.

Start-up

Before using the appliance for the first time, thoroughly

clean out the oil bath (see paragraph entitled “Cleaning

and Taking Care of the Appliance”).

Check that the appliance is connected up properly and

start according to instructions overleaf.

INSTALLATION INSTRUCTIONS

RETRO

BACK

ARRIERE

RÜCKSEITE

019

03 - Electric fryer

Warning!

- Beware of inexpert handling!

- Old and dirty oil or frying fat can represent a real fire

hazard; make sure only new oil or frying fat are used

each time you start frying.

- The food you intend to fry should always be dry; wet

food causes the oil to foam and overflow.

- Frying excessively large quantities of food at a time

also causes the oil to foam; never exceed 1.5 kg.

- If the level of oil in the bath falls below the low level

mark stamped on it, the risk of fire will increase.

- Never leave the appliance on without any oil in it. The

lid delivered with the appliance should always be kept

within easy reach. In case of fire, it should be used to

douse the flames.

Ignition

Check that the oil drain release is closed. Fill the bath with

oil up to the level marked. Turn on the main switch

upstream of the appliance. Turn the knob from ‘0’ to any

temperature between 100°C and 195°C; the pilot lights will

come on. The green light means that the appliance is on,

while the orange one indicates that the resistances are on.

As soon as the required temperature is reached, the oran-

ge light will go off. To turn the appliance off, simply turn the

knob back to '0'.

Emptying the bath

Open the oil drain tap. The appliance is fitted with an oil-

collecting container complete with filter.

CLEANING AND TAKING CARE OF THE

MACHINE

Warning!

Never clean the appliance with jets of water, whether di-

rect or pressurised. Allow the machine to cool down

before cleaning

Before starting to clean the appliance, disconnect from the

mains. Using the hook provided (see drawing 2), you can lift

out the elements to make cleaning the appliance easier and

far more thorough. Lift the elements as far as they will go. To

lower them after cleaning, pull out the button on the left hand

side. All steel parts should be washed in warm water, using a

neutral detergent, then rinsed thoroughly to eliminate any re-

sidual detergent. Dry using a dry cloth. Avoid using abrasive

or corrosive detergents which could damage the steel.

What to do if not using the appliance for

a long time

Thoroughly clean and dry the machine as described.

Disconnect the power supply.

What to do if something goes wrong

If anything goes wrong, immediately turn the appliance off,

then turn off the power supply at the switch located upstream

of the appliance, and call the aftersales department.

MAINTENANCE

All maintenance should be carried out by qualified personnel

only. Before carrying out any maintenance work, unplug the

appliance or turn off the switch upstream of the appliance.

USING THE APPLIANCE

- Bottone

di sgancio

- Pull out button

- Bouton de

déclanchement

- Auslösungknopf

019

03 - Electric fryer

THE 2002/96/EC DIRECTIVE (WEEE):

information to users

This informational note is meant only for owners

of equipment marked with the symbol shown in

Fig. A on the adhesive label featuring the tech-

nical specifications applied on the actual pro-

duct (the label also giving the serial number).

This symbol indicates that the product is classified, ac-

cording to the regulations in force, as an item of electrical

and electronic equipment and conforms to EU Directive

2002/96/EC (WEEE) meaning that, at the end of its service

life, it must be treated separately from domestic waste,

i.e. it must be handed in free of charge to a separate wa-

ste electrical and electronic equipment collection centre

or returned to the reseller when buying a new equivalent

item of equipment.

The user is responsible for delivering the unit at the end of

its life to the appropriate collection facilities. Failure to do

so shall result in the user being subject to the penalties

prescribed by the legislation in force on waste.

Suitable separated collection so that the unit no longer

used can be sent off for environmentally compatible recy-

cling, treatment and disposal helps avoid possible negati-

ve effects on the environment and on health and facilita-

tes the recycling of the product's component materials.

For more detailed information on available collection sy-

stems, contact the local waste disposal service or the

shop you purchased the unit from.

Producers and importers fulfil their responsibility for envi-

ronmentally compatible recycling, treatment and disposal

both directly and by joining a collective scheme.

019

03 - Electric fryer

Wiring diagrams

Line input terminal board

Commutating terminal board

Switch

Microswitch

Safety contactor

Adjusting contactor

Adjusting thermostat

Safety thermostat

Green pilot lamp

Orange pilot lamp

Resistance

AGB 433/WP - AGB 435/WP

AGB 441/WP - AGB 443/WP

H2 H1

400 V 3N

12 5634

230 V 3

123

11 12 13

1 2 34

L1 L2 L3 N

2 3 4

L1 L2 L3

1 3 5

6 2 4

019

03 - Electric fryer

Wiring diagrams

Line input terminal board

Commutating terminal board

Switch

Microswitch

Safety contactor

Adjusting contactor

Adjusting thermostat

Safety thermostat

Green pilot lamp

Orange pilot lamp

Resistance

AGB 437/WP - AGB 439/WP

AGB 445/WP - AGB 447/WP

H2 H1

VUW

YXZ

VUW

YXZ

H2 H1

400 V 3N

230 V 3

1 2 34

1mA 2 3 4

L1 L2 L3

1 3 5

6 2 4

2 3 4

L1 L2 L3 N

019

03 - Electric fryer

WARNING

THE MANUFACTURER CANNOT BE HELD RESPONSIBLE

FOR ANY INACCURACIES IN THIS BOOKLET DUE TO

COPYING OR PRINTING ERRORS.

DUE TO ITS POLICY OF CONTINUAL PRODUCT IMPRO-

VEMENT, THE MANUFACTURER RESERVES THE RIGHT

TO MAKE ANY CHANGES DEEMED NECESSARY.

THE MANUFACTURER CANNOT BE HELD RESPONSI-

BLE IF THE INSTRUCTIONS CONTAINED IN THIS MA-

NUAL ARE NOT OBSERVED.

WHIRLPOOL EUROPE srl

V.le Guido Borghi, 27

I – 21025 Comerio – VA

Whirlpool AGB 433/WP User guide

Whirlpool AGB 433/WP User guide

Whirlpool AGB 433/WP User guide

Related papers

Other documents