Zanussi ZGG646ICY is a gas hob with three burners of different sizes, allowing you to cook multiple dishes simultaneously. It features automatic ignition, eliminating the need for matches or lighters. The flame intensity can be precisely controlled with the knobs, ensuring optimal heat for various cooking techniques. The enamelled components are easy to clean, and the pan supports are dishwasher-safe for added convenience.
Zanussi ZGG646ICY is a gas hob with three burners of different sizes, allowing you to cook multiple dishes simultaneously. It features automatic ignition, eliminating the need for matches or lighters. The flame intensity can be precisely controlled with the knobs, ensuring optimal heat for various cooking techniques. The enamelled components are easy to clean, and the pan supports are dishwasher-safe for added convenience.
Appliance Class 3
GAS
HOB
ZGG 646
INSTRUCTION BOOKLET
DE
3
These instructions are only for the countries stated by the symbol
printed on the front cover of this instruction book.
This appliance complies with the following
E.E.C. Directives:
- 73/23 - 90/683 (Low Voltage Directive);
- 89/336
(Electromagnetical Compatibility Directive);
- 90/396 (Gas Appliances)
- 93/68 (General Directives)
and subsequent modifications.
• This appliance has been designed to be operated by
adults and children under supervision. Young children
MUST NOT be allowed to tamper with the controls or
play near or with the oven.
• This appliance has been designed for non
professional purpose in private houses only. It is
meant to cook edible foodstuff only and MUST NOT be
used for any other purposes.
• It is dangerous to alter the specification in any way.
• For hygiene and safety reasons, this appliance should
be kept clean at all times. A build-up of fats or other
foodstuff could result in a fire.
• Accessible parts of this appliance may become hot
when it is in use. Children should be KEPT AWAY until
it has cooled.
• Under no circumstances should you attempt to repair
the appliance yourself. Repairs carried out by
unexperienced persons may cause injury or serious
malfunctioning. Refer to your local Zanussi Service
Centre. Always insist on genuine Zanussi spare
parts.
• Ensure that all control knobs are in the OFF position
when not in use.
• Should you connect any electrical tool to a plug near
this cooking appliance, ensure that electric cables
are not in contact with it and keep them far enough
from the heated parts of this appliance.
• If the appliance is out of order, disconnect it from the
electric supply.
During Operation
About Installation, Cleaning
and Manteinance
• It is mandatory that all operations required for the
installation are carried out by a qualified or competent
person, in accordance with existing rules and
regulations.
• Disconnect the appliance from the electrical supply,
before carrying out any cleaning or manteinance
work.
• Ensure a good ventilation around the appliance. A
poor air supply could cause lack of oxygen.
• Ensure that the gas supply complies with the gas
type stated on the identification label, placed near
the gas supply pipe.
• Using a gas cooking appliance will produce heat
and moisture in the room which it has been
installed in. Ensure a continuous air supply,
keeping the air vents in good conditions or
installing a cooker hood with discharge tube.
• In case of intensive or long time use of the
appliance, make the ventilation more efficient,
by opening a window or increasing the electric
exhaust fan power.
• Once you removed all packaging from the appliance,
ensure that it is not damaged and the electric cable
is in perfect conditions. Otherwise, contact your
dealer before proceeding with the installation.
• The manufacturer disclaims any responsability
should all the safety measures not be carried
out.
☛
MANUFACTURER:
ELECTROLUX ZANUSSI S.p.A.
Viale Bologna 298 - 47100 FORLI’ (Italy)
For Your Safety
These warnings are provided in the interest of safety. You MUST read them carefully before
installing or using the appliance.
It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred, always ensure that the book is left with
the appliance in order that the new owner can get to know the functions of the appliance and
the relevant warnings.
4
1. Instruction for the User
HOB BURNERS CONTROL KNOBS
The hob burners control knobs are situated on the hob
right hand side. The symbols on the knobs mean that :
● there is no gas supply
there is maximum gas supply
there is minimum gas supply
LIGHTING THE BURNERS
• For easier lighting, proceed before putting a pan
on the pan support.
To light a burner, turn the relevant knob anticlockwise to
maximum position and push down the knob to ignite.
After lighting the flame, keep the knob pushed down for
about 5 seconds. This will allow the "thermocouple"
(Fig. 1 lett. D) to be heated and the safety device to be
switched off, otherwise the gas supply would be
interrupted.
Then, check the flame is regular and adjust it as required.
If you cannot light the flame even after several attempts,
check the "cap" (Fig. 1 lett. A) and the "crown" (Fig. 1 lett.
B) are in the correct position.
To put the flame out, turn the knob to the symbol ●.
• Always turn the flame down or put it out before
taking the pans off the burner.
USING THE HOB CORRECTLY
To ensure maximum burner efficiency, it is strongly
recommended that you use only pots and pans with a
bottom fitting the size of the burner used, so that flame
will not spread beyond the bottom of the vessel (see the
table beside).
It is also advisable, as soon as a liquid starts boiling, to
turn down the flame so that it will barely keep the liquid
simmering.
• Use only pans or pots with flat bottom.
Carefully supervise cookings with fats or oil,
since these types of foodstuff can result in a fire,
if over-heated.
Burner minimum maximum
diameter diameter
Big (rapid) 160 mm. 240 mm.
Medium (semirapid) 120 mm. 220 mm.
Small (Auxiliary) 80 mm. 160 mm.
Fig. 1
Contents
FO 0204
1. Instruction for the User............. Pag. 4
2. Cleaning and Maintenance ....... Pag. 5
3. Technical Data ........................... Pag. 6
4. Instruction for the Installer....... Pag. 6
5. Electrical Connection................ Pag. 7
6. Adaptation to different
types of gas................................ Pag. 8
7. Building In .................................. Pag. 9
5
2. Cleaning and Maintenance
• Disconnect the appliance from the electrical
supply, before carrying out any cleaning or
manteinance work.
Wash the enamelled components with warm soapy
water. Never use abrasive cleaners
Frequently wash the "caps" and the "crowns" with hot
soapy water, carefully taking away any built-up of food.
The pan supports are dishwasher proof.
If the marks are particularly difficult to remove, use
common non-abrasive cleaners or specific products.
Never use steel wool pads or acids.
Regularly wipe over the hob top using a soft cloth weel
wrung out in warm water to which a little liquid detergent
has been added. Avoid the use of the following:
- household detergent and bleaches;
- impregnated pads unsuitable for non-stick saucepans;
- steel wool pads;
- bath/sink stain removers.
Should the hob top become heavily soiled, it is
recommended that a proper cleaning product is used.
The electric ignition is obtained through a ceramic
"candle" and a metal electrode (fig. 1 lett. C). Keep
these components well clean, to avoid difficult lighting,
and check that the burner crown holes (lett. B) are not
obstructed.
PERIODIC MAINTENANCE
Periodically ask your local Service Centre to check the
conditions of the gas supply pipe and the pressure
adjuster, if fitted.
To ensure the good operation of the hob and its safety
features, it is necessary that the taps are periodically
lubricated.
● The periodic lubrication of the taps must be
carried out by qualified personnel, which you
must refer to also in case of malfunctioning.
Fig. 3
FO 2110
Fig. 2
FO 2111
6
3. Technical Data
Gas Burners Rating
Rapid Burner (big) 2,9 kW
Semirapid Burner (medium) 1,9 kW
Auxiliary Burner (small) 1 kW
Category II 2ELL 3 B/P
Setting Natural Gas 20 mba
Gas connection G 1/2"
Electric Supply 230 V 50 Hz
HOB RECESS
DIMENSIONS
Length 550 mm.
Width 470 mm.
4. Instruction for the Installer
● The side walls of the unit in which the hob is
going to be installed, must not exceed the height
of the working top.
● Avoid installing the appliance in the proximity of
inflammable materials (e.g. curtains, tea towels
etc.).
● The following instructions about installation and
maintenance must be carried out by qualified
personnel in compliance with the regulation in
force. The regulations to be applied for this type
of installation are:
— DVGW-TRG '86 "Technical standard for the
installation of gas appliances";
— TRF 1988 "Technical standard for LPG";
● The appliance must be electrically disconnected
before all interventions. If any electric supply to
the appliance is required to carry out the work,
ensure all the necessary precautions are
followed.
GAS CONNECTION
It is indispensible that the connection to the gas mains
are carried out by means of an AGB tap. Choose fixed
connections or use a flexible pipe in AGB (stainless
steel).
If using flexible metallic pipes, be careful they do not
come in contact with mobile parts or they are not
squeezed. Use the same attention when the hob is
combinated with an oven.
This hob can be operated by natural gas with nominal
pressure of 20 mbar. No regulation is required for use by
these two types of gas.
Before fitting the appliance ensure that the installation
has the correct voltage for the appliance. At full capacity,
the drop in pressure must not exceed 5%. Such a drop
in pressure is caused by the following parameters:
- maximum capacity of meter;
- diameter and lenght of the tube in front and behind
the meter;
- section of transit of variuos tubes positioned on the
circuit;
- diameter of eventual connections.
IMPORTANT - To ensure a correct operation, a saving
of energy and the long-life of the appliance, the voltage
pressure of the appliance must correspond to the
recommended values.
The adjustable connection is fixed to the comprehensive
ramp by means of a threaded nut GJ 1/2". Interpose the
sealing between the components as shown in fig. 4.
Screw the parts without forcing, adjust the connection in
the required direction and tighten everything.
IMPORTANT - When the final connection has been
made, it is essential that a thorough leak test is carried
out on the hob and installation. Use some soapy water,
never a flame.
A) Ramp with ending nut
B) Seal
C) Adjustable connection
Fig. 4
FO 0264
7
The appliance is designed to be connected to 230 V
monophase electricity supply.
The connection must be carried out in compliance with
the laws and regulations in force.
Before the appliance is connected:
1) check that the main fuse and the domestic installation
can support the load (see the rating label);
2) check that the power supply is properly earthed in
compliance with the current rules;
3) check the socket or the double pole switch used for
the electrical connection can be easily reached with
the appliance built in the forniture unit.
The appliance is supplied with a connection cable. This
has to be provided with a proper plug, able to support the
load marked on the identification plate. To connect the
plug to the cable, follow the recommendation given in
Fig. 5. The plug has to be fitted in a proper socket.
If connecting the appliance directly to the electric system,
it is necessary that you install a double pole switch
between the appliance and the electricity supply, with a
minimum gap of 3 mm. between the switch contacts and
of a type suitable for the required load in compliance
with the current rules.
The connection cable has to be placed in order that, in
each part, it cannot reach a temperature 80 °C higher
than the room temperature.
The brown coloured phase cable (fitted in the terminal
block contact marked with "L") must always be connected
to the network phase.
REPLACEMENT OF THE VOLTAGE CABLE
Only cable type H05V2V2-F T90 must be used. The
cable section must be suitable to the voltage and the
working temperature.
The yellow/green earth wire must be approximately 2
cm. longer than the phase wires (Fig. 5).
5. Electrical Connection
Fig. 5
FO 0073
Neutral
Earth (yellow/green)
8
Burner NOMINAL REDUCED NOMINAL
POWER POWER POWER
kW kW
NATURAL GAS "E" NATURAL GAS "LL"
LPG
20 mbar 20 mbar 50 mbar
Inject. 1/100 m
3
/h Inject. 1/100 m
3
/h Inject. 1/100 g/h
Auxiliary 1 0,33 70 0,095 74 0,111 43 73
Semi-rapid 1,9 0,45 96 0,181 106 0,210 60 138
Natural gas:
Rapid 2,9 0,65 119 0,276 133 0,321 75 196
LPG: 2,7
Fig. 6
FO 0392
Table 2 : injectors
Fig. 7
FO 0239
INJECTORS REPLACEMENT
• Remove the pan supports.
• Remove the burner's caps and crowns.
• With a socket spanner 7 unscrew and remove the
injectors (Fig. 6), and replace them with the ones
required for the type of gas in use (see table 2).
• Reassemble the parts, following the same procedu-
re backwards.
• Replace the rating label (placed near the gas supply
pipe) with the relevant one for the new type of gas
supply. You can find this label in the package of the
injectors supplied with the appliance.
Should the feeding gas pressure be different or
variable compared with the required pressure, an
appropriate pressure adjuster must be fitted on the gas
supply pipe, in compliance with the rules in force.
ADJUSTMENT OF MINIMUM LEVEL
To adjust the minimum level of the burners, proceed as
follows:
• Light the burner.
• Turn the knob on the minimum position.
• Remove the knob.
• With a thin screwdriver, adjust the by-pass screw
positioned in the centre of the gas tap control shaft
(see Fig. 7). If changing from natural gas "E" to
natural gas "LL", undo the by-pass screw until a
small regular flame is obtained. If changing from
natural gas "E" to LPG, completely tighten clockwise
the screw, until a small regular flame is obtained.
• Finally check the flame does not go out when quickly
turning the knob from the maximum position to the
minimum position.
This procedure can easily be carried out, anyhow the
hob has been positioned or built in the working top.
Burner Ø By-pass Tap
in 1/100 colour
of mm.
Auxiliary 28 Blue/White
Semi-rapid 32 Red/Yellow
Rapid 40 Blue/Yellow
Table 1 : By-pass diameters
6. Adaptation to different types of gas
9
550
470
580
510
55 min.
7. Building In
Fig. 8
A = Auxiliary burner SR = Semirapid burner
R = Rapid Burner
These hobs can be inserted in a built-in kitchen unit
whose depth is between 550 and 600 mm. The hobs
dimensions are shown in Fig. 9.
The edge of the cut out must have a minimum distance
from the rear wall of 55 mm.
If there are side walls, or sides of the furniture unit near
the hob, the cut out edges must have a minimum
distance of 100 mm.
Hanging forniture units or hoods must be placed at 650
mm. minimum from the hob.
FO 2034
a) Sealing gasket
FITTING THE HOB TO THE WORKTOP
Before fitting the hob into the cut out, an adhesive seal
must be fitted to the underside outside edge (Fig. 9) of
the hob. It is essential that no gaps are left in this seal
in order to prevent spillage near the hob seeping into
the cabinet below.
1) Remove the pan supports, the burners caps and
crowns and turn the hob upside down, taking care the
ignition candles are not damaged in this operation.
2) Place the sealing gasket all around the glass top
edge as shown in Fig. 9.
3) Fit the hob in the cut out and push it down until the
glass top and the working top come in touch, as shown
in Fig. 10.
Fig.9
A
Fig.10
FO 2108
FO 2107
SR
SR
R
A
10
a) Removable panel
b) Space possibly useful for
connections
550 min.
560 min.
Fig. 11
Fig. 12
Fig. 14
Fig. 15
FO 1013 FO 0947
FO 0939
FO 0938
FO 0198
470
30
591
380
140
POSSIBILITIES FOR
INSERTION
Kitchen unit with door
Proper arrangements must be taken in designing the
forniture unit, in order to avoid any contact with the
bottom of the hob which can be heated when it is
operated. The recommended solution is shown in Fig.
11.
The panel fitted under the hob should be easily
removable to allow an easy access if a technical
assistance intervention is needed.
Fig. 13
Kitchen unit with oven
The hob recess dimensions must comply the indication
given in Figs. 12 and 13 and must be provided with
brackets to allow a continuous supply of air.
To avoid overhating, the building in should be carried
out as shown in Figs. 14 e 15.
The hob's electric connection and the oven's one must
be carried out separately, both for safety reasons and
to allow the oven to be easily taken off the unit.
30
20 min
60
a
b
120 cm
2
180 cm
2
360 cm
2
50 cm
2
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
Zanussi ZGG646ICY User manual
- Category
- Hobs
- Type
- User manual
Zanussi ZGG646ICY is a gas hob with three burners of different sizes, allowing you to cook multiple dishes simultaneously. It features automatic ignition, eliminating the need for matches or lighters. The flame intensity can be precisely controlled with the knobs, ensuring optimal heat for various cooking techniques. The enamelled components are easy to clean, and the pan supports are dishwasher-safe for added convenience.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Electrolux ZGG646ICY User manual
-
Zanussi ZGG643ICY User manual
-
Zanussi ZGF 648 User manual
-
-
-
-
Electrolux ZGF64XK User manual
-
-
-
Other documents
-
Electrolux EGG646ICN User manual
-
AEG 32514DG-M User manual
-
Aeg-Electrolux 79553G-M User manual
-
-
-
-
Electrolux EHG3760X User manual
-
-
-