Whirlpool AGB 454/WP is an electric Bain-Marie with a 230 V power supply and a power of 2.0 kW. It has dimensions of 800 x 900 x 270 mm and weighs approximately 67 kg. The device is equipped with a temperature regulator, water inlet, line warning light, resistances warning light, and water outlet. It also has a 12 mm ø fitting for the water inlet and a 3/4” male connection for the outlet. The Whirlpool AGB 454/WP is designed for use in commercial kitchens and can be used to keep food warm and ready to serve. It is also suitable for use in buffets and self-service areas.
Whirlpool AGB 454/WP is an electric Bain-Marie with a 230 V power supply and a power of 2.0 kW. It has dimensions of 800 x 900 x 270 mm and weighs approximately 67 kg. The device is equipped with a temperature regulator, water inlet, line warning light, resistances warning light, and water outlet. It also has a 12 mm ø fitting for the water inlet and a 3/4” male connection for the outlet. The Whirlpool AGB 454/WP is designed for use in commercial kitchens and can be used to keep food warm and ready to serve. It is also suitable for use in buffets and self-service areas.
017_03
Installation, operating and
maintenance instructions
07/2007
ELECTRIC BAIN-MARIE
AGB 453/WP · AGB 454/WP
017
-
03 - Electric Bain-Marie
2
Models and dimensions pag. 3
Data of appliances 5
Installation instructions 6
Installation 6
Legal and technical requisites 6
Installation 6
Wiring 6
Unipotential 6
Plumbing connection 6
Using the appliance 7
Ignition 7
Emptying the bath 7
Cleaning and taking care
of the appliance 7
What to do if not using the appliance for
a long time 7
What to do if something goes wrong 7
Maintenance 7
WEEE Directive 7
Wiring diagrams 8
Warning 9
INDEX
017
-
03 - Electric Bain-Marie
3
Temperature regulator
Water inlet
Line warning light
Resistances warning light
Water outlet
A
B
C
D
E
B
D
E
C
A
B
D
E
C
A
Dimensions
017
-
03 - Electric Bain-Marie
4
Dimensions
AGB 453/WP
Weight approx.61 kg
AGB 454/WP
Weight approx.67 kg
Temperature regulator
Water inlet
Line warning light
Resistances warning light
Water outlet
A
B
C
D
E
A
D
E
C
B
A
D
E
C
B
017
-
03 - Electric Bain-Marie
5
Model
AGB 453/WP
AGB 454/WP
Dim.: LxWxH
400 x 900 x 875
800 x 900 x 875
400 x 900 x 270
800 x 900 x 270
Voltage rating
230 V
230 V
230 V
230 V
Power
1.0 kW
2.0 kW
1.0 kW
2.0 kW
Lead wire / Section
3 x 1.5 mm
2
3 x 2.5 mm
2
3 x 1.5 mm
2
3 x 2.5 mm
2
2 - CHARACTERISTICS OF THE APPLIANCES
3 - TECHNICAL DATA
TIPO/TYPE
CAT/KAT GAS/GAZ G30 G31 G20 G25
II2H3B/P P mbar 30 30 20 -
II2H3+ P mbar 30 37 20
-
-
II2H3+ P mbar 28 37 20 -
25II2L3B/P P mbar 30 30
II2ELL3B/P P mbar 50 50 20 20
II2E+3+ P mbar 28 37 20 25
II2H3B/P P mbar 50 50 20 -
I2E P mbar - - 20 -
--II2H3B/P P mbar 30 30
II2H3+ P mbar 28 37 20 -
--
--
I3B/P P mbar 30 30
I3+ P mbar 28 37
SE FI DK CZ SK SI
IT CH PT
ES IE GB GR
NL
DE
FR BE
AT CH
LU
EE LV LT
EE LV LT
NO MT CY IS HU
CY
MOD.
MOD.
ART.
N.
N.
Qn kW
m
3
/h
MADE IN ITALY
Predisposto a gas: - Gas preset: - Prevu pour gaz:
Eingestelt für Gas: - Preparado para gas: -
Geschuckt voor:
V AC kW Hz
THE APPLIANCE MUST BE CONNECTED IN COMPLIANCE WITH THE LAWS IN FORCE
AND INSTALLED IN A WELL-VENTILATED ROOM. READ THE INSTRUCTION MANUALS
BEFORE INSTALLING AND USING THE APPLIANCE.
THE APPLIANCE MUST BE INSTALLED BY QUALIFIED PERSONNEL.
The data plate is located on the rigth hand side of the
control panel and contains all the data needed for connecting
it up to the mains electricity supply.
017
-
03 - Electric Bain-Marie
6
INSTALLATION
Before beginning installation, remove all packaging from
the appliance. Some parts are protected with an adhesive
film which should be carefully removed.
Any remnants of glue should be thoroughly cleaned using
suitable substances such as benzine. Under no circum-
stances should abrasive substances be used.
Fit the legs to the appliance; the appliance must be level-
led using a spirit level. Slight irregularities can be levelled
by adjusting the feet themselves.
With table models, make sure that the base chosen is ca-
pable of supporting the weight of the appliance. The main
switch or plug should be located in the vicinity of the ap-
pliance and easy of access. We recommend installing the
machine under a range hood so that all the fumes are re-
moved as quickly as possible. If the appliance is to be in-
stalled near walls, dividing walls, kitchen equipment or
decorative pannelling, these should be in non-inflamma-
ble material or covered with non-inflammable material.
Make sure that all fire prevention standards and safety pre-
cautions are strictly adhered to.
Legal and technical requisites
When installing the appliance, the following safety stan-
dards must be adhered to:
- Local accident prevention standards
- Current CEI standards.
Installation
Installation, start-up and maintenance should only be car-
ried out by expert personnel. All work required to install
the appliance should be carried out in compliance with all
local standards and regulations. The manufacturers decli-
ne all responsibility where poor performance is due to in-
correct installation in disregard of the above conditions.
Warning!
In compliance with international regulations, when
connecting the appliance to the mains power supply, a
device with a minimum aperture of 3 mm between con-
tacts must be fitted upstream of the appliance, al-
lowing omnipolar disconnection of the appliance from
the mains.
Wiring
When choosing the lead wire, make sure it has the fol-
lowing characteristics: it should be at least of the H07 RN-
F type and its section should be large enough for the ap-
pliance (see "Technical specifications and dimensions",
page 5).
The cable inlet and terminal board are to be found on the
mains supply box, situated near the front left foot.
Pass the wire through the core hitch and wire clamp, plug
the leads into their terminals on the board and secure
them.
The earth lead must be a little longer than the others so
that it is the last lead to disconnect if the wire clamp
breaks.
Unipotential
The appliance must be connected up to a unipotential
system.
The connecting screw is placed on the mains supply box
and is marked with a plaque.
Plumbing connection
The 12 mm ø fitting for the water inlet is placed under-
neath to the right.
To connect, use the pipe fitting supplied with the applian-
ce, taking into account that a 3/8” female is to be inserted.
The outlet has a 3/4” male connection located near the in-
let.
Warning!
The manufacturers cannot be held responsible for any
damage due to inadequate or incorrect installation.
Under such circumstances the guarantee will be con-
sidered null and void.
INSTALLATION INSTRUCTIONS
017
-
03 - Electric Bain-Marie
7
Warning!
- Beware of inexpert handling!
- Never leave the appliance on without any water in it.
Ignition
Check that the water drain release is closed. Using knob
(B) (water inlet, see “Conventional representation” on pa-
ge 3-4), fill the tank up to the overflow level.
Use the on/off switch on the mains supply line to the ap-
pliance to switch on.
Turn knob (A) (thermostat switch, see “Conventional re-
presentation” on page 3-4) to the position required,
anywhere between 30°C and 90°C.
The warning lights come on: the green warning light indi-
cates that the appliance is live, the yellow light that the re-
sistances are inserted; as soon as the required tempera-
ture is reached, the latter goes out.
To turn the appliance off, simply turn the knob back to '0'.
Emptying the bath
The drain cock lever can be found in the bottom compart-
ment and is placed in the centre of the roof.
CLEANING AND TAKING CARE OF THE
MACHINE
Warning!
Never clean the appliance with jets of water, whether
direct or pressurised.
Allow the machine to cool down before cleaning
Before starting to clean the appliance, disconnect from
the mains.
All steel parts should be washed in warm water, using a
neutral detergent, then rinsed thoroughly to eliminate any
residual detergent. Dry using a dry cloth.
Avoid using abrasive or corrosive detergents which could
damage the steel.
What to do if not using the appliance
for a long time
Thoroughly clean and dry the machine as described.
Disconnect the power supply.
What to do if something goes wrong
If anything goes wrong, immediately turn the appliance
off, then turn off the power supply at the switch located
upstream of the appliance, and call the aftersales depart-
ment.
MAINTENANCE
All maintenance should be carried out by qualified per-
sonnel only. Before carrying out any maintenance work,
unplug the appliance or turn off the switch upstream of the
appliance.
The 2002/96/EC (WEEE) Directive:
information to users
This informational note is meant only for owners
of equipment marked with the symbol shown in
Fig. A on the adhesive label featuring the tech-
nical specifications applied on the actual pro-
duct (the label also giving the serial number).
This symbol indicates that the product is classified, accor-
ding to the regulations in force, as an item of electrical
and electronic equipment and conforms to EU Directive
2002/96/EC (WEEE) meaning that, at the end of its service
life, it must be treated separately from domestic waste, i.e.
it must be handed in free of charge to a separate waste
electrical and electronic equipment collection centre or re-
turned to the reseller when buying a new equivalent item
of equipment.
The user is responsible for delivering the unit at the end of
its life to the appropriate collection facilities. Failure to do
so shall result in the user being subject to the penalties
prescribed by the legislation in force on waste.
Suitable separated collection so that the unit no longer
used can be sent off for environmentally compatible recy-
cling, treatment and disposal helps avoid possible negati-
ve effects on the environment and on health and facilitates
the recycling of the product's component materials.
For more detailed information on available collection sy-
stems, contact the local waste disposal service or the
shop you purchased the unit from.
Producers and importers fulfil their responsibility for envi-
ronmentally compatible recycling, treatment and disposal
both directly and by joining a collective scheme.
USING THE APPLIANCE
017
-
03 - Electric Bain-Marie
8
H1 H2
R1
230 V
1mA
2
L1 N
B1
F1
R1
3
PN
H1 H2
R1
230 V
1mA 2
L1 N
B1
F1
3
PN
Line input terminal board
Green pilot lamp
Orange pilot lamp
Resistance
Switch
Thermostat
mA
H1
H2
R1
B1
F1
AGB 454/WP
AGB 453/WP
Wiring diagrams
017
-
03 - Electric Bain-Marie
9
WARNING
THE MANUFACTURER CANNOT BE HELD RESPONSIBLE
FOR ANY INACCURACIES IN THIS BOOKLET DUE TO
COPYING OR PRINTING ERRORS.
DUE TO ITS POLICY OF CONTINUAL PRODUCT IMPRO-
VEMENT, THE MANUFACTURER RESERVES THE RIGHT
TO MAKE ANY CHANGES DEEMED NECESSARY.
THE MANUFACTURER CANNOT BE HELD RESPONSI-
BLE IF THE INSTRUCTIONS CONTAINED IN THIS MA-
NUAL ARE NOT OBSERVED.
WHIRLPOOL EUROPE srl
V.le Guido Borghi, 27
I – 21025 Comerio – VA
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
Whirlpool AGB 454/WP User guide
- Type
- User guide
- This manual is also suitable for
Whirlpool AGB 454/WP is an electric Bain-Marie with a 230 V power supply and a power of 2.0 kW. It has dimensions of 800 x 900 x 270 mm and weighs approximately 67 kg. The device is equipped with a temperature regulator, water inlet, line warning light, resistances warning light, and water outlet. It also has a 12 mm ø fitting for the water inlet and a 3/4” male connection for the outlet. The Whirlpool AGB 454/WP is designed for use in commercial kitchens and can be used to keep food warm and ready to serve. It is also suitable for use in buffets and self-service areas.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Whirlpool AGB 532/WP User guide
-
Whirlpool AGB 508/WP User guide
-
-
-
Whirlpool AGB 433/WP User guide
-
Whirlpool ASE 568 Installation guide
-
-
-
Whirlpool AGB 058/WP User guide
-
Whirlpool AGB 552/WP User guide
Other documents
-
Blue Seal EB45D Operating instructions
-
Hendi 225707 User manual
-
Metos OCPE 60 Operating instructions
-
Bartscher 1311413 Operating instructions
-
Diamond GT4S77 Operating Instructions Manual
-
Groupe Brandt BCG6611W1 Owner's manual
-
Zanussi ZOG21311XK User manual
-
-
-
Cannon C50GKXF Operating instructions