003_03
Instructions for installation,
use and maintenance
07/2007
ELECTRIC BAIN-MARIE
AGB 591/WP
AGB 531/WP
AGB 532/WP
003
-
03 - Electric bain-marie
Models and dimensions page 3
Technical data 6
Installation instructions 7
Installation 7
Legal and technical requisites 7
Installation 7
Wiring 7
Unipotential 7
Ignition 7
Emptying the bath 8
Cleaning and taking care
of the appliance
8
What to do if not using the appliance for
a long time 8
What to do if something goes wrong 8
Maintenance 8
WEEE Directive 8
Wiring diagrams 9
Warning 10
2
INDEX
003
-
03 - Electric bain-marie
3
1 - DIAGRAM
B
E
D
A
C
B
E
D
A
C
B
E
D
A
C
AGB 591/WP
Weight approx.19 kg
Temperature control
Water drain
release
Switch
Resistance pilots
Water drain
A
B
C
D
E
003
-
03 - Electric bain-marie
4
1 - DIAGRAM
B
E
D
A
C
B
E
D
A
C
B
E
D
A
C
AGB 531/WP
Weight approx.19 kg
AGB 532/WP
Weight approx.32 kg
Temperature control
Water drain
release
Switch
Resistance pilots
Water drain
A
B
C
D
E
003
-
03 - Electric bain-marie
5
1 - DIAGRAM
B
E
D
A
C
B
E
D
A
C
B
E
D
A
C
Temperature control
Water drain
release
Switch
Resistance pilots
Water drain
A
B
C
D
E
003
-
03 - Electric bain-marie
6
2 - CHARACTERISTICS OF THE APPLIANCES
Model
AGB 591/EP
AGB 531/WP
AGB 532/WP
Dim.: LxWxH
400 x 615 x 300
400 x 700 x 300
400 x 700 x 875
800 x 615 x 300
800 x 700 x 300
800 x 700 x 875
Voltage rating
230 V
230 V
230 V
230 V
230 V
230 V
Power
1.0 kW
1.0 kW
1.0 kW
2.0 kW
2.0 kW
2.0 kW
Lead wire / Section
3 x 1.5 mm
2
3 x 1.5 mm
2
3 x 1.5 mm
2
3 x 2.5 mm
2
3 x 2.5 mm
2
3 x 2.5 mm
2
3 - TECHNICAL DATA
TIPO/TYPE
CAT/KAT GAS/GAZ G30 G31 G20 G25
II2H3B/P P mbar 30 30 20 -
II2H3+ P mbar 30 37 20
-
-
II2H3+ P mbar 28 37 20 -
25II2L3B/P P mbar 30 30
II2ELL3B/P P mbar 50 50 20 20
II2E+3+ P mbar 28 37 20 25
II2H3B/P P mbar 50 50 20 -
I2E P mbar - - 20 -
--II2H3B/P P mbar 30 30
II2H3+ P mbar 28 37 20 -
--
--
I3B/P P mbar 30 30
I3+ P mbar 28 37
SE FI DK CZ SK SI
IT CH PT
ES IE GB GR
NL
DE
FR BE
AT CH
LU
EE LV LT
EE LV LT
NO MT CY IS HU
CY
MOD.
MOD.
ART.
N.
N.
Qn kW
m
3
/h
MADE IN ITALY
Predisposto a gas: - Gas preset: - Prevu pour gaz:
Eingestelt für Gas: - Preparado para gas: -
Geschuckt voor:
V AC kW Hz
THE APPLIANCE MUST BE CONNECTED IN COMPLIANCE WITH THE LAWS IN FORCE
AND INSTALLED IN A WELL-VENTILATED ROOM. READ THE INSTRUCTION MANUALS
BEFORE INSTALLING AND USING THE APPLIANCE.
THE APPLIANCE MUST BE INSTALLED BY QUALIFIED PERSONNEL.
The data plate is located on the rigth hand side of the
control panel and contains all the data needed for connecting
it up to the mains electricity supply.
Before beginning installation, remove all packaging from
the appliance. Some parts are protected with an adhesive
film which should be carefully removed.
Any remnants of glue should be thoroughly cleaned using
suitable substances such as benzine. Under no circum-
stances should abrasive substances be used.
Fit the legs to the appliance; the appliance must be level-
led using a spirit level. Slight irregularities can be levelled
by adjusting the feet themselves.
With table models, make sure that the base chosen is ca-
pable of supporting the weight of the appliance. The main
switch or plug should be located in the vicinity of the ap-
pliance and easy of access. We recommend installing the
machine under a range hood so that all the fumes are re-
moved as quickly as possible. If the appliance is to be in-
stalled near walls, dividing walls, kitchen equipment or de-
corative pannelling, these should be in non-inflammable
material or covered with non-inflammable material.
Make sure that all fire prevention standards and safety pre-
cautions are strictly adhered to.
Warning!
With Top models, carefully measure the distance
between the appliance and the edge of the base (Fig. 2).
Legal and technical requisites
When installing the appliance, the following safety stan-
dards must be adhered to:
- Local accident prevention standards
- Current CEI standards.
Installation
Installation, start-up and maintenance should only be car-
ried out by expert personnel. All work required to install
the appliance should be carried out in compliance with all
local standards and regulations. The manufacturers decli-
ne all responsibility where poor performance is due to in-
correct installation in disregard of the above conditions.
Warning!
In compliance with international regulations, when
connecting the appliance to the mains power supply, a
device with a minimum aperture of 3 mm between con-
tacts must be fitted upstream of the appliance, al-
lowing omnipolar disconnection of the appliance from
the mains.
Wiring
When choosing the lead wire, make sure it has the fol-
lowing characteristics: it should be at least of the H07 RN-
F type and its section should be large enough for the ap-
pliance (see "Technical specifications and dimensions",
page 6).
Wire entry on top models is on the back wall, and under-
neath all other models. In both cases the terminal board is
at the front, behind the control panel.
Pass the wire through the core hitch and wire clamp, plug
the leads into their terminals on the board and secure
them.
The earth lead must be a little longerthan the others so
that it is the last lead to disconnect if the wire clamp
breaks.
Unipotential
The appliance must be connected up to a unipotential sy-
stem. The connection screw is located on all top models
at the back on the right hand side, while in other models it
is located underneath the appliance on the right hand si-
de. It is labelled.
Warning!
The manufacturers cannot be held responsible for any
damage due to inadequate or incorrect installation.
Under such circumstances the guarantee will be con-
sidered null and void.
Warning!
- Beware of inexpert handling!
- Never leave the appliance on without water!
Ignition
Check that the water drain release is closed. Fill the bath
with water up to the level marked. Turn on the main switch
upstream of the appliance.
On the twin-bath models (AGB 532/WP) both baths can
be used independently of each other at different tempera-
tures, or one can be used without the other. Turn the main
switch on the appliance. It will light up indicating that the
appliance is on.
Switch on switch C (pages 4 ...5) and use knob A to posi-
tion the thermostat on the desidered temperature,
between 30°C and 90°C inclusive; the pilot light will come
on; this means that the resistances are on. As soon as the
required temperature is reached, the pilot light will go off.
To turn the appliance off, simply turn the knob back to '0'
and switch off.
INSTALLATION INSTRUCTIONS
003
-
03 - Electric bain-marie
7
Emptying the bath
First of all a suitable bowl for emptying the water into
should be found. Fit the drainage pipe as shown in the
picture (2). Open the oil drain tap.
Important
With Top models, make sure you respect the distance
between the appliance and the edge of the base.
CLEANING AND TAKING CARE OF THE
MACHINE
Warning!
Never clean the appliance with jets of water, whether
direct or pressurised.
Allow the machine to cool down before cleaning
Before starting to clean the appliance, disconnect from
the mains.
All steel parts should be washed in warm water, using a
neutral detergent, then rinsed thoroughly to eliminate any
residual detergent.
Dry using a dry cloth. Avoid using abrasive or corrosive
detergents which could damage the steel.
What to do if not using the appliance
for a long time
Thoroughly clean and dry the machine as described.
Disconnect the power supply.
What to do if something goes wrong
If anything goes wrong, immediately turn the appliance
off, then turn off the power supply at the switch located
upstream of the appliance, and call the aftersales depart-
ment.
MAINTENANCE
All maintenance should be carried out by qualified per-
sonnel only. Before carrying out any maintenance work,
unplug the appliance or turn off the switch upstream of the
appliance.
USING THE APPLIANCE
003
-
03 - Electric bain-marie
8
MAX 120 mm
2
THE 2002/96/EC DIRECTIVE (WEEE):
information to users
This informational note is meant only for owners
of equipment marked with the symbol shown in
Fig. A on the adhesive label featuring the tech-
nical specifications applied on the actual pro-
duct (the label also giving the serial number).
This symbol indicates that the product is classified, ac-
cording to the regulations in force, as an item of electrical
and electronic equipment and conforms to EU Directive
2002/96/EC (WEEE) meaning that, at the end of its service
life, it must be treated separately from domestic waste,
i.e. it must be handed in free of charge to a separate wa-
ste electrical and electronic equipment collection centre
or returned to the reseller when buying a new equivalent
item of equipment.
The user is responsible for delivering the unit at the end of
its life to the appropriate collection facilities. Failure to do
so shall result in the user being subject to the penalties
prescribed by the legislation in force on waste.
Suitable separated collection so that the unit no longer
used can be sent off for environmentally compatible recy-
cling, treatment and disposal helps avoid possible negati-
ve effects on the environment and on health and facilita-
tes the recycling of the product's component materials.
For more detailed information on available collection sy-
stems, contact the local waste disposal service or the
shop you purchased the unit from.
Producers and importers fulfil their responsibility for envi-
ronmentally compatible recycling, treatment and disposal
both directly and by joining a collective scheme.
003
-
03 - Electric bain-marie
9
ELECTRICAL DIAGRAMS
H1
mA
L1 N PE
B1
123
F1
R1
T2
H1
mA
L1 N PE
B1
123
F1
R1
T2
H1
B1
F1
R1
T2
230 V
230 V
Terminal board
Main switch (green light)
Thermostat
Pilot lamp
Resistances
mA
B1
F1
H1
R1
AGB 591/WP
AGB 531/WP
AGB 532/WP
003
-
03 - Electric bain-marie
10
WARNING
DUE TO ITS POLICY OF CONTINUAL PRODUCT IMPRO-
VEMENT, THE MANUFACTURER RESERVES THE RIGHT
TO MAKE ANY CHANGES DEEMED NECESSARY.
THE MANUFACTURER CANNOT BE HELD RESPONSI-
BLE IF THE INSTRUCTIONS CONTAINED IN THIS MA-
NUAL ARE NOT OBSERVED.
THIS DOCUMENTATION IS ONLY INTENDED FOR
QUALIFIED TECHNICIANS WHO ARE AWARE OF THE
RESPECTIVE SAFETY REGULATIONS.
WHIRLPOOL EUROPE srl
V.le Guido Borghi, 27
I – 21025 Comerio – VA
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Whirlpool AGB 532/WP User guide
- Type
- User guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Whirlpool AGB 454/WP User guide
-
-
-
Whirlpool AGB 433/WP User guide
-
Whirlpool ASE 568 Installation guide
-
Whirlpool AGB 528/WP User guide
-
Whirlpool AGB 058/WP User guide
-
Whirlpool AGB 552/WP User guide
-
-