Whirlpool AGB 508/WP is a professional electric tilting cooker with a 5.0 kW power and a voltage rating of 230 V 3 or 400 V 3N. It has dimensions of 400 x 700 x 300 mm and weighs approximately 72 kg.
Whirlpool AGB 508/WP is a professional electric tilting cooker with a 5.0 kW power and a voltage rating of 230 V 3 or 400 V 3N. It has dimensions of 400 x 700 x 300 mm and weighs approximately 72 kg.
066_03
Installation, operating and
maintenance instructions
07/2007
ELECTRIC TILTING COOKER
AGB 508/WP
CHARACTERISTICS
066_03 - Electric tilting cooker
2 · 10
07/2007
Supplied by:
Date:
Customer Service:
FAX
e-mail
INDEX
066_03 - Electric tilting cooker
3 · 10
07/2007
1 Diagram 4
2 Characteristics of the appliances 5
3 Technical data 5
4 Installation instructions 6
4.1 Installation 6
4.2 Legal and technical requisites 6
4.2.1 Installation 6
4.2.2 Wiring 6
4.2.3 Unipotential 6
4.2.4 Start-up 6
5 Set-up for operation 7
5.1 Ignition 7
5.2 Cleaning and taking care of the appliance 7
5.3 What to do if not using the appliance for a long time 7
5.4 What to do if something goes wrong 7
5.5 Maintenance 7
5.5.1 WEEE Directive 7
6 Instructions for use 8
7 Appendix: Electrical diagrams 9
1 - DIAGRAM
066_03 - Electric tilting cooker
4 · 10
07/2007
B
A
CD
B
A
CD
B
A
CD
AGB 508/WP
400 x 700 x 870
Weight approx. 72 kg
A
B
C
D
Knob
Oil drip tray
Green pilot lamp
Yellow pilot lamp
2 - CHARACTERISTICS OF THE APPLIANCES
3 - TECHNICAL DATA
066_03 - Electric tilting cooker
5 · 10
07/2007
These appliances are used for professional purposes. Installation,
repair and use must be carried out by expert personnel.
The data plate is located on the front part of the appliance (on the
control panel).
Model
AGB 508/WP
Dim.: LxWxH (total h)
of work surface
400 x 615 x 300
400 x 700 x 300
400 x 700 x 870
Voltage rating
230 V 3 or 400 V 3N
230 V 3 or 400 V 3N
230 V 3 or 400 V 3N
Power
5.0 kW
5.0 kW
5.0 kW
Lead wire / Section
4 x 1.5 mm
2
or
5 x 1.5 mm
2
4 x 1.5 mm
2
or
5 x 1.5 mm
2
4 x 1.5 mm
2
or
5 x 1.5 mm
2
TIPO/TYPE
CAT/KAT GAS/GAZ G30 G31 G20 G25
II2H3B/P P mbar 30 30 20 -
II2H3+ P mbar 30 37 20
-
-
II2H3+ P mbar 28 37 20 -
25II2L3B/P P mbar 30 30
II2ELL3B/P P mbar 50 50 20 20
II2E+3+ P mbar 28 37 20 25
II2H3B/P P mbar 50 50 20 -
I2E P mbar - - 20 -
--II2H3B/P P mbar 30 30
II2H3+ P mbar 28 37 20 -
--
--
I3B/P P mbar 30 30
I3+ P mbar 28 37
SE FI DK CZ SK SI
IT CH PT
ES IE GB GR
NL
DE
FR BE
AT CH
LU
EE LV LT
EE LV LT
NO MT CY IS HU
CY
MOD.
MOD.
ART.
N.
N.
Qn kW
m
3
/h
MADE IN ITALY
Predisposto a gas: - Gas preset: - Prevu pour gaz:
Eingestelt für Gas: - Preparado para gas: -
Geschuckt voor:
V AC kW Hz
THE APPLIANCE MUST BE CONNECTED IN COMPLIANCE WITH THE LAWS IN FORCE
AND INSTALLED IN A WELL-VENTILATED ROOM. READ THE INSTRUCTION MANUALS
BEFORE INSTALLING AND USING THE APPLIANCE.
THE APPLIANCE MUST BE INSTALLED BY QUALIFIED PERSONNEL.
4 - INSTALLATION INSTRUCTIONS
066_03 - Electric tilting cooker
6 · 10
07/2007
4.1 Installation
• Before beginning installation, remove all packaging from the
appliance.
• Some parts are protected with an adhesive film which should be
carefully removed.
• Any remnants of glue should be thoroughly cleaned using suita-
ble substances such as benzine. Under no circumstances should
abrasive substances be used.
• Fit the legs to the appliance; the appliance must be levelled using
a spirit level. Slight irregularities can be levelled by adjusting the
feet themselves. With table models, make sure that the base cho-
sen is capable of supporting the weight of the appliance. The
main switch or plug should be located in the vicinity of the
appliance and easy of access. We recommend installing the
machine under a range hood so that all the fumes are removed
as quickly as possible.
• If the appliance is to be installed near walls, dividing walls, kit-
chen equipment or decorative pannelling, these should be in
non-inflammable material or covered with non-inflammable
material. Make sure that all fire prevention standards and safety
precautions are strictly adhered to.
Warning!
MODEL AGB 508/WP
• if this model is going to be mounted on its own, it must
be fixed to the floor. Fixing accessories are included. The
appliance should be fitted following the indications given
in the drawing below.
4.2 Legal and technical requisites
When installing the appliance, the following safety standards must
be adhered to:
- Local accident prevention standards
- Current CEI standards.
RETRO
BACK
ARRIERE
RÜCKSEITE
4.2.1 Installation
• Installation, start-up and maintenance should only be carried out
by expert personnel.
• All work required to install the appliance should be carried out
in compliance with all local standards and regulations.
• The manufacturers decline all responsibility where poor perfor-
mance is due to incorrect installation in disregard of the above
conditions.
Warning!
• In compliance with international regulations, when con-
necting the appliance to the mains power supply, a device
with a minimum aperture of 3 mm between contacts
must be fitted upstream of the appliance, allowing omni-
polar disconnection of the appliance from the mains.
4.2.2 Wiring
• When choosing the lead wire, make sure it has the following
characteristics: it should be at least of the H07 RN-F type and its
section should be large enough for the appliance (see "Technical
specifications and dimensions", page 5).
• Wire entry on top models is on the back wall, and underneath
all other models.
• In both cases the terminal board is at the front, behind the con-
trol panel. Pass the wire through the core hitch and wire clamp,
plug the leads into their terminals on the board and secure
them. The earth lead must be a little longerthan the others so
that it is the last lead to disconnect if the wire clamp breaks.
4.2.2 Unipotential
• The appliance must be connected up to a unipotential system.
The connection screw is located on all top models at the back on
the right hand side, while in other models it is located under-
neath the appliance on the right hand side. It is labelled.
Warning!
• The manufacturers cannot be held responsible for any
damage due to inadequate or incorrect installation. Under
such circumstances the guarantee will be considered null
and void.
4.2.3 Start-up
• Before using the appliance for the first time, thoroughly clean
the tank (see “Cleaning and Taking Care of the Appliance”) to
remove the protective film of mineral oil applied in the factory.
• Check installation and wiring, then turn the appliance on fol-
lowing the instructions below, and leave on, empty, for about 15
mins.
5 - SET-UP FOR OPERATION
066_03 - Electric tilting cooker
7 · 10
07/2007
Warning!
- Beware of inexpert handling!
5.1 Ignition
• Check that the overflow is in place. Turn on the main switch
upstream of the appliance. Turn the thermostat to any position
between 50°C and 300°C; the pilot lights will come on; the green
one shows that the appliance is on, the yellow one shows that the
resistances are on. As soon as the required temperature is reached,
the yellow light goes off.
• To turn the appliance off, simply turn the knob back to '0'.
5.2 Taking care of the appliance - Frequency
of maintenance
Attention!
Never clean the appliance with jets of water, whether direct or
pressurised. Allow the machine to cool down before clea-
ning
• Giving the appliance a thorough clean every day (after turning it
off) will keep it in perfect working order and make it last longer.
• All steel parts should be cleaned with water and a detergent, using
a damp cloth; do not use abrasive substances or corroding deter-
gents.
• Do not use steel wool, which could leave traces of rust. For the
same reason, avoid touching the appliance with anything made of
iron.
• Do not clean any parts of the appliance other than the grilling plate
with emery or sandpaper. If absolutely necessary, you may use pow-
dered pumice stone.
• If the appliance is extremely dirty, use a synthetic sponge such as
Scotchbrite.
• After cleaning the appliance, rinse with clean water and dry with a
clean cloth.
• To make cleaning easier is possible to installed a tilting tank.
• All maintenance work must be carried out by qualified personnel
only.
• Have the appliance checked at least once a year; we strongly recom-
mend that you stipulate a servicing and maintenance contract with
your supplier.
Warning!
• The first time you use the pan, wash it with soap and water.
• Never use synthetic cloth to clean, only cotton, wool or linen
• Never fill the bottom of the pan with grease
• Do not fill the tank with oil; it cannot be used for frying
because of the fire hazard represented by the oil .
5.3 What to do if not using the appliance for
a long time
• Thoroughly clean and dry the machine as described. Disconnect the
power supply.
• After cleaning, we recommend you grease the pan with
vegetable oil.
5.4 What to do if something goes wrong
• If anything goes wrong, immediately turn the appliance off, then
turn off the power supply at the switch located upstream of the
appliance, and call the aftersales department.
5.5 MAINTENANCE
• All maintenance should be carried out by qualified personnel only.
Before carrying out any maintenance work, unplug the appliance
or turn off the switch upstream of the appliance.
5.5.1
The 2002/96/EC (WEEE) Directive:
information to users
This informational note is meant only for
owners of equipment marked with the
symbol shown in Fig. A on the adhesive
label featuring the technical specifications
applied on the actual product (the label
also giving the serial number):
This symbol indicates that the product is classified, according
to the regulations in force, as an item of electrical and elec-
tronic equipment and conforms to EU Directive 2002/96/EC
(WEEE) meaning that, at the end of its service life, it must be
treated separately from domestic waste, i.e. it must be han-
ded in free of charge to a separate waste electrical and elec-
tronic equipment collection centre or returned to the reseller
when buying a new equivalent item of equipment.
The user is responsible for delivering the unit at the end of
its life to the appropriate collection facilities. Failure to do so
shall result in the user being subject to the penalties prescri-
bed by the legislation in force on waste.
Suitable separated collection so that the unit no longer used
can be sent off for environmentally compatible recycling,
treatment and disposal helps avoid possible negative effects
on the environment and on health and facilitates the recy-
cling of the product's component materials.
For more detailed information on available collection
systems, contact the local waste disposal service or the shop
you purchased the unit from.
Producers and importers fulfil their responsibility for environ-
mentally compatible recycling, treatment and disposal both
directly and by joining a collective scheme.
6 - INSTRUCTIONS FOR USE
066_03 - Electric tilting cooker
8 · 10
07/2007
NOTES
7 - APPENDIX: ELECTRICAL DIAGRAMS
066_03 - Electric tilting cooker
9 · 10
07/2007
B1
F1
1mA 2 345
6
12
3
456
L1 L2 L3 N
12
11
R1 R1 R1
mA2 345
6
L1 L2 L3
12
3
4
56
R1
12 22 32
11 21 31
F2
PE
C1
A1
A2
H1
H2
400V 3N
230V 3
1
AGB 508/WP
mA
B1
F1
F2
C1
H1
H2
R1
Line input terminal board
Switch
Thermostat
Safety thermostat
Contactor
Green pilot lamp
Orange pilot lamp
Resistance 1750 W
Total power:
5000 W
WARNING
THE MANUFACTURER CANNOT BE HELD RESPONSIBLE
FOR ANY INACCURACIES IN THIS BOOKLET DUE
TO COPYING OR PRINTING ERRORS.
DUE TO ITS POLICY OF CONTINUAL PRODUCT IMPROVEMENT,
THE MANUFACTURER RESERVES THE RIGHT
TO MAKE ANY CHANGES DEEMED NECESSARY.
THE MANUFACTURER CANNOT BE HELD RESPONSIBLE
IF THE INSTRUCTIONS CONTAINED IN THIS MANUAL
ARE NOT OBSERVED.
WHIRLPOOL EUROPE srl
V.le Guido Borghi, 27
I – 21025 Comerio – VA
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Whirlpool AGB 508/WP is a professional electric tilting cooker with a 5.0 kW power and a voltage rating of 230 V 3 or 400 V 3N. It has dimensions of 400 x 700 x 300 mm and weighs approximately 72 kg.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Whirlpool AGB 058/WP User guide
-
Whirlpool AGB 433/WP User guide
-
Whirlpool AGB 552/WP User guide
-
Whirlpool AGB 466/WP User guide
-
-
-
-
Whirlpool AGB 590/WP User guide
-
-
Other documents
-
Hendi 225707 User manual
-
Bartscher 2856011 Operating instructions
-
Metos OPCG 41 Operating instructions
-
Bartscher 2853101 Operating instructions
-
Bartscher 2953031 Operating instructions
-
Metos 76/02CTGG Operating instructions
-
Diamond GT4S77 Operating Instructions Manual
-
-