Andersen E-Series Casement and Awning Windows Service Instructions

Brand: Andersen

Model: E-Series Casement and Awning Windows

Type: Service Instructions

Use caution when working at elevated heights and around unit openings.

Follow manufacturers’ instructions for ladders and/or scaffolding. Failure

to do so may result in injury or death.

Follow manufacturers’ instructions for hand or power tools. Always

wear safety glasses. Failure to do so may result in injury and/or

product damage.

9069237 BA Revised 04/30/13

Tools Needed

∙Safety Glasses

∙Flat Pry Bar

∙Flat Blade Screwdriver

∙Drill/Driver

∙#2 Phillips Bit

Operator Replacement

for E-Series Casement and Awning Windows with Standard Hinge

Parts Included

(1) Operator

Operator

Thank you for choosing Andersen.

For questions call 1-888-888-7020. For more information and/or guides visit www.eaglewindow.com.

Please leave this guide with building owner.

▶Read guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.

▶Check with your local building code ofcial to identify and conrm compliance with local building code requirements.

Casement window shown in guide.

9069237

Remove sill cover using a at pry bar and save for reuse.

Loosen set screw on handle using a small at blade screwdriver.

Remove handle and save for reuse. Remove operator cover and save for

reuse.

Remove handle and save for reuse.

Interior

Handle

Flat Blade

Screwdriver

Set Screw

Operator Cover

Operator

Interior

Remove screws from sill cover and save for reuse.

Remove screws from sill cover using a drill/driver and save for reuse.

Drill/Driver

Flat Blade Pry Bar

Sill Cover

Interior

Open lock handle. Temporarily apply operator handle and open sash. Remove operator

handle and save for resuse.

Lock Handle

Operator Handle

Interior

9069237

Align straight operator arm with arrow on operator channel. Depress straight operator arm down to release from operator channel.

Interior

Slide split operator arm clip from operator bracket stud with at blade

screwdriver. Release split operator arm from operator bracket stud.

Releasing operator arm allows sash to swing freely. Sash

may suddenly swing out and break free causing injury and/

or product damage. Support sash during entire replacement

process.

Straight Operator Arm

Straight Operator Arm Roller

Operator Channel

Split Operator Arm Clip

Operator Bracket Stud

Flat Blade Screwdriver

Split Operator Arm

Interior

Remove operator and save screws for reuse. Dispose of old operator

properly.

Fasten new operator in same position using saved screws. Position split operator arm on sash bracket stud. Slide clip on sash

bracket stud.

Interior

Operator Bracket Stud

Split Operator Arm

Interior

Arrow Arrow

New Operator

Drill/Driver

Operator

Drill/Driver

Flat Blade

Screwdriver

Split Operator

Arm Clip

9069237

Align straight operator arm roller with arrow on operator channel and insert it into operator channel.

Interior

Straight Operator Arm

Operator Channel

Close lock handle.Temporarily apply operator handle and close

sash. Remove operator handle and save for

reuse.

Slide sill cover into place over operator and

between side stops.

Sill Cover

Interior

Fasten sill cover using saved screws.

▶Operator replacement is completed.

Tighten handle set screw.

Set Screw

Reapply operator cover. Reapply handle.

Reapply operator cover.

Operator Cover

Operator

Handle

Flat Blade

Screwdriver

Lock Handle

Interior

Arrow

Straight Operator

Arm Roller

Side Stop

OperatorOperator Handle

Drill/Driver

Sill Cover

Andersen E-Series Casement and Awning Windows Service Instructions

Andersen E-Series Casement and Awning Windows Service Instructions

Andersen E-Series Casement and Awning Windows Service Instructions

Related papers

Other documents