Lutron Electronics SQE-2 User manual

Brand: Lutron Electronics

Model: SQE-2

Category: Numeric keypads

Type: User manual

SQE-2

SQE-RL

SQE-3E

SQE-3D

SQE-33

Sivoia QED

™

Euro-style

Keypads

for use with Lutron Sivoia QEDTM

Motorized Window Treatment System

Open button

Status Indicator

LEDs

Open button

SQE-2

Status Indicator

LEDs

SQE-RL

SQE-3D

Open button

Close button

SQE-33

SQE-3E

Infrared

Receiver

Raise/Lower

Installation Instructions

Occupant Copy

Please read before installing.

CAUTION

Lutron recommends that Keypads be installed by a qualified electrician.

Do not connect high-voltage power to low-voltage terminals. Improper wiring can result in personal injury or damage to

the control or to other equipment.

Keypads must be connected to the Sivoia QEDTM Electronic Drive Unit (EDU) by using Class 2 (USA)/ PELV(IEC) wiring

methods. Check with your local electrical inspector for the local code requirements and wiring practices

allowed in your area.

Use only a cloth with warm water and mild soap to clean faceplates (no chemical cleaners).

Keypad Configurations

Status Indicator

LEDs

Raise button

Lower button

Preset button

Close button

Raise/Lower

Status Indicator

LEDs

Preset button

Close button

Open button

Status Indicator

LEDs

Group Selection

LEDs

Preset button

Close button

Group 1 button

Group 2 button

Group 3 button

Button Functionality

Tap the Open, Close, or Preset button to move the window

treatments to the selected position. While pressing the Raise or

Lower button, the window treatments will raise or lower.

Numbers - Tapping one of the numbered buttons

will select a group of EDUs to control.

Open - Tap the open button to move the window

treatments to the fully-open position.

Preset - Tap the preset button to move the window

treatments to their programmed preset level.

Close - Tap the close button to move the window

treatments to the fully-closed position.

Raise - Holding the raise button will move the

window treatments towards the open position.

Releasing the raise button will cause the window

treatments to stop.

Lower - Holding the lower button will move the

window treatments towards the closed position.

Releasing the lower button will cause the window

treatments to stop.

Note: Holding the or buttons for 5 seconds

will cause the window treatments to move all the

way open or closed automatically.

3Occupant Copy Installation Instructions

Wiring Notes

System Maximums:

— Up to 96 devices total on one system.

One transformer per EDU.

— The Keypads wire to the Sivoia QED Communication

Link. The Link can not exceed 1220 m (4000 ft) total.

— The Keypads are either powered by EDUs or Keypad

Power Supplies. Each EDU can provide power for one

Keypad.

The number of Keypads should not exceed

the number of EDUs unless connecting with a Keypad

Power Supply.

— The maximum distance between any two Sivoia QED

devices is 305 m (1000 ft) unless specified otherwise.

— Operating environment should be between 0 °C -

40 °C (32 °F - 104 °F).

Keypad Wiring

— Two 1.0 mm

(#18 AWG) wires for power and two

shielded 1.0 mm

(#18 AWG) stranded wires for data

(twisted pair).

— Power: wires 1 & 2, 12 - 15 V .

— Data: wires 3 & 4, twisted, shielded pair.

Sivoia QED Link wiring layouts are shown on the next

page.

1, 2, 3

Sivoia QED Link:

Class 2/PELV Wiring

connections to EDUs,

Power Panels, or

other Keypads.

Male EDU Connector

Sivoia QED Keypad Wiring

Installation Instructions Occupant Copy4

4. Each Keypad terminal will accept up to two 1.0 mm

(#18 AWG) wires.

Connect two 1.0 mm

(#18 AWG) wires to terminals 1 and

2 of the Keypad’s terminal block.

Connect two 1.0 mm

(#18 AWG) shielded, twisted pair

wires to terminals 3 and 4 of the Keypad’s terminal block.

Common

12V

MUX

AC1

AC2

EGND

Female EDU

Connector

Sivoia QED EDU

Back of

Sivoia QED Keypad

Installation

Keypad circuits are classified as Class 2 circuits (U.S.A.) and

PELV circuits (IEC). When installing and wiring to these

Keypads, follow all applicable national and/or local wiring

regulations.

Warning: Always turn Off the circuit breaker or

remove the main fuse from the power line before

doing any work.

Failure to do so can result in

serious personal injury

1. Turn power Off to all EDUs and power panels.

2. Mount standard German or UK backboxes (60 mm

measured centre to centre of mounting holes).

3. Strip insulation from wires so that 10 mm. (3/8 in) of bare

wire is exposed for 1.0 mm

(#18 AWG) wire.

OFF

10 mm (3/8 in.)

5Occupant Copy Installation Instructions

5. Remove the faceplate from the Keypad. To remove the

faceplate, pull outward at each corner, one corner at a

time.

6. Mount Keypad as shown in the diagram below.

7. Attach faceplate by pressing in at each corner, one corner

at a time.

Thread all four screws before tightening.

Wallbox

Wall

Mounting Frame Orientation

Wallbox

Mounting

Frame

Carrier Faceplate

Mounting

Frame

Addressing the System

Note: For the SQE-RL, use the and buttons instead of

the and buttons.

1. Enter programming mode on the Keypad by pressing and

holding the Open ( ) and Close ( ) buttons

simultaneously for 5 seconds. The LEDs next to the Open

( ) and Close ( ) buttons will flash once per second,

indicating the Keypad is in Programming mode.

2. Initiate system addressing by tapping the Open ( ) button.

The LED next to the Open ( ) button will flash quickly (8

times a second) and the LED next to the Close ( ) button

will turn off. The system is now being automatically

addressed.

Press the Open ( ) and

Close ( ) buttons

simultaneously for 5

seconds.

Flashing

once per

second

3. Wait for system addressing to be completed. This will take

approximately one minute. While addressing is in progress,

each Keypad will flash the Open ( ) LED quickly (8 times

a second). When addressing has successfully completed,

the Open ( ) and Close ( ) LEDs on each Keypad in the

system will flash slowly (once per second).

4. When system addressing is complete, exit Programming

mode by pressing and holding the Open ( ) and Close

( ) buttons simultaneously for 5 seconds. The Open ( )

and Close ( ) LEDs will stop flashing.

Tap the Open ( )

button.

Flashing 8

times per

second

4. Adjust the currently selected EDU to the desired level,

using the Raise ( ) and Lower ( ) buttons on the

Keypad.

Setting Limits

Note: Entering Limit Setup mode may cause the

window treatments to move approximately 200 mm

(8 in) up or down.

Be sure that each window

treatment is positioned such that the fabric can safely

move approximately 200 mm (8 in) before entering

Limit Setup mode.

Note:

When using Keypads that do not have Raise and Lower

buttons, set the limits at the EDU. Refer to the

Sivoia QED

Wiring and Programming Guide for more information.

1. If using the SQE-33, select the group you wish to assign.

2. Enter Limit Setup mode by pressing and holding the Open

( ) and Raise ( ) buttons simultaneously for 5 seconds.

The LED next to the Open ( ) button will flash once per

second and the LED next to the Close ( ) button will flash

quickly (8 times per second).

3. Select the EDU to adjust using the Open ( ) button on the

Keypad. Each time the Open ( ) button is tapped, an EDU

will begin opening and closing over a range of

approximately 200 mm (8 in). Repeat tapping the Open ( )

button until the desired EDU is selected. The Close ( )

button can also be used to select EDUs by moving through

the EDUs in the opposite order.

5. Store the current position as the Open ( ) limit by

pressing and holding the Open ( ) button on the Keypad

for 5 seconds. The LED next to the Open ( ) button will

turn on for two seconds.

Store the current position as the Close ( ) limit by

pressing and holding the Close ( ) button on the Keypad

for 5 seconds. The LED next to the Close ( ) button will

turn on for two seconds.

6. Use the Open ( ) or Close ( ) buttons to select other

window treatments and adjust the limits as in Steps 3 and

7. Exit Limit Set mode by pressing and holding the Open ( )

and Raise ( ) buttons simultaneously for 5 seconds.

Installation Instructions Occupant Copy

LED on for 2

seconds

Press & hold

here to set the

Open ( ) limit

Press the Open ( )

and Raise ( ) buttons

simultaneously for 5

seconds.

LED flashing once

per second

LED flashing 8 times

per second

Press the Raise ( ) or

Lower ( ) button.

LED on for 2

seconds

Press & hold

here to set the

Close ( ) limit

7Occupant Copy Installation Instructions

EDU Assignment

Note: Entering Assignment mode will cause the

window treatments to move between their Open and

Close limits.

Be sure that the Open and Close

limits have been set appropriately.

Note:

For the SQE-RL, use the and buttons instead of

the and buttons.

1. If using the SQE-33, select the group you wish to assign.

2. Enter Programming mode on the Keypad by pressing and

holding the Open ( ) and Close ( ) buttons

simultaneously for 5 seconds. The LEDs next to the Open

( ) and Close ( ) buttons will flash once per second,

indicating the Keypad is in Programming mode.

3. Initiate Assignment mode by tapping the Close ( ) button.

The LED next to the Close ( ) button will continue to flash

(once per second) and the LED next to the Open ( )

button will turn off. EDUs that are assigned to the Keypad in

Assignment Mode will move to their Close limit. EDUs that

are not assigned to the Keypad will move to their Open

limit.

4. Tap any button on an EDU to toggle between assignment

or unassignment with the Keypad.

Use the Open ( ) button to step through each EDU in the

system. Each time the Open ( ) button is tapped, a

window treatment will begin opening and closing over

approximately 200 mm (8 in). Repeat tapping the Open

( ) button until the desired EDU is selected. The Close

( ) button can also be used to select EDUs in the

opposite order.

5. Assign or unassign the currently selected EDU using the

Raise ( ) and Lower ( ) buttons. To assign, tap the

Lower ( ) button. To unassign, tap the Raise ( )

button.

6. Check assignment before exiting Assignment mode. EDUs

that are at the Close limit are assigned. EDUs that are at

the Open limit are unassigned.

7. Exit Assignment mode by pressing and holding the Open

( ) and Close ( ) button simultaneously for 5 seconds.

Each EDU will return to the level it was at when

Assignment mode was entered. The Open ( ) and Close

( ) LEDs will stop flashing.

Press the Open ( )

and Close ( )

buttons

simultaneously for 5

seconds.

Flashing

once per

second

Tap the Close ( )

button.

Flashing

once per

second

Tap the Raise ( )

or Lower ( )

button.

Lutron Electronics Co., Inc.

7200 Suter Road

Coopersburg, PA 18036 U.S.A.

Made and printed in U.S.A.

P/N 040-227-12 Rev. A 1/05

Limited Warranty

Lutron EA Ltd. (“Lutron EA”) warrants each unit to be free from defects in material and

workmanship and to perform under normal use and service. To the extent permitted by law,

Lutron EA and Lutron Electronics Co. Inc. (“Lutron”) make no warranties or representations as

to the units except as set forth herein. This warranty shall run for a period of one year from the

date of purchase and Lutron’s obligations under this warranty are limited to remedying any

defect, replacing any defective part or replacement (at Lutron EA’s sole option) and shall be

effective only if the defective unit is shipped to Lutron EA postage prepaid within 12 months

after purchase of the unit, to the extent permitted by law. Repair or replacement of the unit

does not affect the expiry date of the warranty.This warranty does not cover damage or

deficiencies due to abuse, misuse, inadequate wiring or insulation or use or installation other

than in accordance with instructions accompanying the unit.

Although every attempt is made to ensure that catalogue information is accurate and up-to-

te,

please check with Lutron EA bef

ore specifying or purchasing this equipment to confirm

availability, exact specifications, and suitability for your application.

This warranty does not affect the statutory rights of consumer purchasers of the unit.

These products may be covered by one or more of the following US patents: 4,835,343;

4,924,349; D422,567; D436,930; D453,742; D456,783; D461,782; D465,460; D465,770;

D466,090; D466,091; D466,484; D475,024; D475,025; and corresponding foreign patents.

US and foreign patents pending. Lutron, the Sunburst logo, and Sivoia are registered

trademarks, and Sivoia QED is a trademark of Lutron Electronics Co., Inc.

Inc.

Note: The current position is stored as a preset only on the

EDUs that are assigned to that preset button. The preset is only

accessable from that particular Keypad.

Troubleshooting

For information on troubleshooting, please refer to the Sivoia

QED

Wiring and Programming Guide.

Storing Presets

Sivoia QED EDUs have the ability to store positions as presets.

1. Set all EDUs controlled by the Keypad to the desired level

using the Raise ( ) and Lower ( ) buttons on the

Keypad.

2. Store the EDUs’ current position as a preset by pressing

and holding the desired Preset ( ) button for 5 seconds.

The LED next to the Preset button ( ) on the Keypad will

flash and then turn on, indicating that the preset has been

stored.

Technical Assistance

EUROPEAN HEADQUARTERS

Lutron EA Ltd.

6 Sovereign Close

London, E1W 3JF

United Kingdom

Tel: +44-(0)20-7702-0657

Fax: +44-(0)20-7480-6899

CUSTOMER SERVICE/ORDERING

UK +44-(0)20-7702-0657 –

09.00 - 18.00 GMT

USA +1-610-282-3800 –

08.00 - 20.00 EST

CUSTOMER SERVICE/E-MAIL

[email protected]

TECHNICAL SUPPORT & SERVICES

UK +44-(0)20-7702-065709.00 -

18.00 GMT

USA +1-610-282-3800 – 24 hours/7

days

INTERNET: www.lutron.com

WORLD HEADQUARTERS

Lutron Electronics Co.,

Inc.

7200 Suter Road

Coopersburg, PA 18036

United States

Tel: +1-610-282-3800

Fax:+1-610-282-1243

Press the Preset ( )

button for 5

seconds.

LED will

flash and

then turn

on.

Lutron Electronics SQE-2 User manual

Brand: Lutron Electronics

Model: SQE-2

Category: Numeric keypads

Type: User manual

Download PDF

report

Lutron Electronics SQE-2 User manual

Lutron Electronics SQE-2 User manual

Related papers

Other documents