Extreme Tools RX723001HCBLBK Owner's manual

Brand: Extreme Tools

Model: RX723001HCBLBK

Type: Owner's manual

Models:

RX723001HC 72”W x 30”D

RX553001HC 55”W x 30”D

72 inch Steel Top Hutch

shown on RX723016RC

Owner’s Manual

Professional Steel

Hutches

Extreme Tools, Inc.

740 Frontenac Rd.

Naperville, Illinois 60563

630.369.9303

www.ExtremeTools.net

[email protected]

RX723001HC

Parts List

ITEM NO PART NUMBER DESCRIPTION QTY

1 7225HC-01 TOP BACK PANEL 1

2 7230HC-02 SIDE PANEL ASSY-LH 1

3 7230HC-05 SIDE PANEL ASSY-RH 1

4 Z-M5X16SHDS M5-16MM SOCKET HEAD SCREW 2

5 Z-M10PLUG M10 PLASTIC HOLE PLUG 2

6 GAS STRUT (350) 350MM FULLY EXTENDED 2

7 POWER STRIP POWER STRIP W/USB OUTLET 1

8 RUBBER GROMMET-2 RUBBER GROMMET 2

9 7225HC-20 SPLICER POST ASSEMBLY 2

10 Z-SMS SHEET METAL SCREW 2

11 Z-M5X16PHMS M5X16MM PAN HEAD MS 25

13 Z-RB12M RUBBER BUMPER 12MM SQ 1

14 7225HC-22 HOLD-DOWN BRACKET 2

15 Z-M8-1.25-20SHS M8X20 SOCKET HEAD CAP SCREW 2

16 Z-WAFM8 M8 FLAT WASHER 2

17 7225HC-10 TOP LID ASSY 1

18 7225HC-13 FRONT LID SUB-ASSY 1

19 RXPTUSL UNIVERSAL POWER TOOL RACK 1

20 Z-M4-0.5LN M4-0.5 LOCKNUT 4

21 Z-MSM4-0.7X10MMPH M4-0.7X10MM PAN HEAD MS 4

22 7230HC-19 ADJUSTABLE SHELF 1

23 7230 Spacer Panel

72”Wide x 5” Deep Spacer Panel

ITEM NO PART NUMBER DESCRIPTION QTY

1 5525HC-01 TOP BACK PANEL 1

2 7230HC-02 SIDE PANEL ASSY-LH 1

3 7230HC-05 SIDE PANEL ASSY-RH 1

4 Z-M5X16SHDS M5-16MM SOCKET HEAD SCREW 2

5 Z-M10PLUG M10 PLASTIC HOLE PLUG 2

6 GAS STRUT (350) 350MM FULLY EXTENDED 2

7 POWER STRIP POWER STRIP W/USB OUTLET 1

8 RUBBER GROMMET-2 RUBBER GROMMET 2

9 7225HC-20 SPLICER POST ASSEMBLY 2

10 Z-SMS SHEET METAL SCREW 2

11 Z-M5X16PHMS M5X16MM PAN HEAD MS 18

13 Z-RB12M RUBBER BUMPER 12MM SQ 1

14 7225HC-22 HOLD-DOWN BRACKET 2

15 Z-M8-1.25-20SHS M8X20 SOCKET HEAD CAP SCREW 2

16 Z-WAFM8 M8 FLAT WASHER 2

17 5525HC-10 TOP LID ASSY 1

18 5525HC-13 FRONT LID SUB-ASSY 1

19 RXPTUSL UNIVERSAL POWER TOOL RACK 1

20 Z-M4-0.5LN M4-0.5 LOCKNUT 4

21 Z-MSM4-0.7X10MMPH M4-0.7X10MM PAN HEAD MS 4

22 5530HC-19 ADJUSTABLE SHELF 1

5530 Spacer Panel

55”W x 5”D Spacer Panel 1

RX553001HC

Parts List

Step 1: Attach Splicer Posts to Side Panels

a. Slide Splicer Post Assembly (#9) into bottom opening of the

left-hand Side Panel Assembly(#2).

NOTE: If the hutch is going to be used over the stainless

steel surface, then remove the spacer on the bottom of the

side panel.

b. Line up hole in Splicer Post with hole in Side Panel.

c. Insert Sheet Metal Screw (#10)

and tighten. Do not completely tighten

until hutch is fully assembled.

d. Repeat for the right-hand

side.

SPACER

Step 2: Install Side Panels on Roller Cabinet

a. Remove plastic end caps from the top of the trim located at the

front corners of the roller cabinet.

b. Slide end of splicer channel into opening where plastic end

cap was located until side panel rests on top of MDF/Stainless

Steel Top.

c. Repeat process for right-hand side.

Plastic

End

Cap

Plastic End Cap

Step 3: Secure Side Panels

a. Loosely install one Hold-Down Bracket (#14) on each side

using one at washer (#16) and one M8 bolt (#15) for each

side.

If attaching the side locker or side box, do not use Hold-Down

Bracket on that side.

OPTION: To make installing the back panel easier, you may wait

until the end to install Hold-Down Bracket.

Hold-Down

Bracket

Flat

Washer

M8 Bolt

Back Raised Edge

(aka: Fence Rail)

Step 4: Install Adjustable Shelf

a. Determine the desired height for the Adjustable Shelf. Pre-thread

(2) screws (#11) about halfway in on left-hand and right-hand

sides.

b. Locate the (2) open slots on each side of the shelf. Line up the

open slots with the (4) threaded screws that were installed in

Step 5d. Lay down shelf so that (4) open slots t on top of the (4)

screws.

c. Loosely tighten (4) screws.

Determine adjustable shelf

height. Pre-thread (2) screws

about halfway in on each side

at desired height.

Step 5: Install Back Panel

a. Pull MDF board/Stainless Steel Top forward approximately 1/8”

from Back Raised Edge (aka: Fence Rail.)

b. Lift Back Panel into place behind the two side panels. (BACK

PANEL is HEAVY and requires 2 people to place!) Slide the

bottom edge of the Back Panel between the MDF/Stainless Steel

Top and rear fence rail of roller cabinet. Flange on left and right

sides of back panel should be resting against the inside back

edges of both side panels.

Back Raised Edge

(aka: Fence Rail)

Back panel ange should

rest inside the Side

Panel

Slide Back Panel down

behind Side Panels with

bottom of Back Panel tting

between roller cabinet fence

rail and top work surface.

Step 6: Secure Back Panel

c. Use (6) M5 screws (#11) on each side to fasten the back panel

to side panel assemblies.

d. Repeat on for right-hand side panel.

e. Locate (2) threaded inserts on the back of the shelf. From the

back of the Back Panel, insert (2) screws through the back of

the pegboard and and through the threaded inserts of the shelf

and tighten.

Locate threaded inserts

and insert (2) screws

through the back

pegboard then through

shelf holes to secure

shelf to Back Panel.

Secure side panel to back panel using (6)

M5x16mm Pan Head Screws

Step 8: Attach Gas Struts to Lid

a. Lay the lid down on packaging material so that the front of the lid

is face down. Be sure to use packaging material under the lid so

that it does not get scratched or damaged.

b. Locate the (2) openings near the Top Panel Stiffener.

c. Hold each gas strut so that the larger cylinder end is up and

the smaller piston end is down. Insert the male portion at the

cylinder end of the gas strut into the opening near the top lid

stiffener. Tighten to secure in place.

d. Repeat step c for the other side.

Top of the lid

Opening to

insert male

portion of

gas strut

Opening to insert

male portion of

gas strut

Front Panel of lid

Attach long

side of spacer

to back panel

top section

and short

sides to top of

side panels.

Step 7: Attach Spacer Panel

a. After the back panel has been installed, attach the spacer panel to

the top section of the back panel. Use (3) M5x16mm pan head

screws to secure spacer panel to top section of back panel.

Use (4) addtional screws to attach the spacer to the top of both

side panels.

Step 10: Secure Lid to Body of Hutch

a. Use the Allen wrench (supplied with the parts) to drive the pre-

threaded M5-16mm Sock Head Screw (#4) into the round

opening on the side of the lid.

b. Insert one plastic hole plug (#5) in each of the socket head

screw openings.

Top of Lid

Side of Hutch

M5-16mm Socket

Head Screw

Drive screw into

opening on side

of lid using Allen

wrench

Step 9: Install the Lid onto the body of the Hutch

LID is HEAVY!

LID INSTALLATION REQUIRES ASSISTANCE to LIFT

and MAY REQUIRE the USE of MECHANICAL EQUIPMENT to

PROPERLY POSITION!

a. Lift the lid into place on top of the hutch body as shown below.

Step 12: Final Details

a. If you did not install the Hold Down Bracket in Step 3, then do so

now.

b. Securely tighten ALL screws and bolts!

Step 11: Secure Gas Strut to Side of Hutch

a. Prop open the lid so that it cannot fall.

b. Install the male tting on the piston end of the gas strut into

the opening near the inside top of the side panel.

c. Repeat for the gas strut on the other side.

Secure the male

end of the piston

into the opening

on the side of the

hutch

FULLY ASSEMBLED

RX SERIES HUTCH

shown on

ROLLER CABINET

Extreme Tools RX723001HCBLBK Owner's manual

Brand: Extreme Tools

Model: RX723001HCBLBK

Type: Owner's manual

Download PDF

report

Extreme Tools RX723001HCBLBK Owner's manual

Extreme Tools RX723001HCBLBK Owner's manual

Related papers

Other documents