Charging stand for single MPA
AX-ST-CH-A1
Instruction Manual
1WMPD4003080A
Safety Use
Please note the following items when the device is used.
CAUTION
1. Introduction
This manual describes how the AX-ST-CH-A1 charging stand for a
single MPA works. To fully understand and make use of the product,
please read this manual carefully before use. Also, please read the
instruction manual for the MPA.
2. Package Contents and Each Part Name
Package contents
࣭Charging stand for single MPA
࣭Linking cable (AX-KO4730-10)
࣭Instruction manual (This document)
Each part name
Charging hanger
(1)
Charging terminals:
Receive an MPA for charging.
(2)
Power indicator LED:
Lights up in green when power is supplied to the charging stand.
(3)
Input section:
Connects with the cable from the AC adapter provided for the
MPA main unit. To link another stand, connect the output section
(4) with the input section (3) of the stand to be added using the
linking cable. (Connects with Mini USB- Type B).
(4)
Output section:
Used for linking multiple charging stands.
(Connects with USB- Type A)
3. Features
ڦ Charging starts automatically when an MPA is hooked onto the
charging stand.
ڦ Power supply stops automatically when charging is complete.
ڦ Space saving installation (60 mm (excluding the stand feet) × 154
mm)
ڦ By linking up to three charging stands, it is possible to charge
three MPAs at the same time.
4. How to Use
Prepare the power cable and AC adapter (AX-TB265) that are
provided with MPA and connect them to this device.
Charging the MPA
1. Insert the AC adapter into an outlet. The power indicator LED
(Green) (2) will light up.
2. Hook an MPA onto the charging section to begin charging. While
charging, the battery indicator on the MPA display blinks as shown
in the following figure to indicate that the device is being charged.
3. Charging is complete when the battery
indicator is fully lit.
4. The MPA can continue to be hooked to the
charging stand after it is fully charged.
(It will not be overcharged.)
5.Linking Charging Stands
Up to three charging stands can be used in conjunction to charge
multiple MPAs simultaneously.
(The following figure shows the example of two units.)
When moving the charging stands, be
sure to hold them with both hands.
Moving them with one hand may
cause them to drop.
Linking charging stands
1. Remove the four stand feet located on the sides of the stands
to be attached.
2. Join the upper and lower male parts on one stand to the upper
and lower female parts on the other, and then push them in.
3. Attach two stand feet as shown in the following figure. The
stand feet also link the charging stands.
* Only two stand feet are used.
4. Connect the output section (4) of the charging hanger with the
input section (3) of the stand to be added using the linking
cable.
5. Insert the AC adapter connected with the power cable into an
outlet. The power indicator LEDs (Green) (2) of each of the two
charging hangers will light up, and two MPAs can be charged
simultaneously.
6. Specifications
Input (Specified adapter) AC 100 V㸭0.3A (50㸭60 Hz)
Input section / output
section
DC 5V
Connectable devices
Electronic pipette MPA series
Dimensions
95(W)335(H)154(D)mm
Net weight Approx. 500g
(Excluding the AC adapter)
7. Accessories
࣭Linking cable࣭࣭࣭࣭࣭࣭࣭࣭࣭࣭࣭࣭࣭࣭࣭AX-KO4730-10
࣭
AC adapter for the MPA࣭࣭࣭࣭࣭࣭࣭࣭࣭࣭࣭࣭AX-TB265
(The AX-TB265 is the standard accessory for the electronic
pipette
MPA series.)
© 2015 A&D Company Ltd. All rights reserved.
No part of this publication may be reproduced, transmitted,
transcribed, or translated into any language in any form by any
means without the written permission of A&D Company Ltd.
The contents of this manual and the specifications of the
instrument covered by this manual are subject to change fo
improvement without notice.
ڦ Do not disassemble the device. Any damage or loss o
functions caused by disassembly is not covered by warranty.
ڦ Do not link more than the maximum of three charging stands.
Linking four units or more may cause fire or damage the units
or the MPA series of electronic pipettes (hereinafter called
MPA).
ڦ Use the AC adapter provided for the MPA main unit, as
otherwise the charging stand, the MPA, or the power suppl
devices may be damaged.
᪥ᮏㄒࡢྲྀᢅㄝ᫂᭩ࡣᑐ㠃ࢆࡈぴࡃࡔࡉ࠸ࠋ
2) Power indicator LED
(1) Charging
terminals
3
In
ut section
(4) Output section
[Front view]
[Rear view]
an
connec
on par
U
er male
art
Cable insertion section
an
connec
on par
(Lower male part)
Stand foot
Cable clam
an
connec
on par
(Upper and lower female
parts)
USB- T
e A
Mini USB- T
e B
Char
in
han
e
Charging stand for single MPA
(Power cable connected)
Charging stand to be added
Linking cable
ڦConnect the power cable to
the input section (3) so that
the USB mark on the USB-
Type B of the power cable
faces the device.
ڦRun the power cable to the
back side of the charging
stand through the cable
insertion section, and then
push it into the three cable
clamps.
ڦConnect the USB- Type A to
the AC adapter.
C ada
te
Remove the stand
feet.
lign the connection parts to combine the
two charging stands.
ttach the stand feet to link the two
charging stands, with the front foot
and the rear foot facing opposite
directions.
Push the stand feet until they are fully
inserted into the stand bases.
-3-
Linking cable
Char
in
stand for sin
le MPA
USB- T
pe A
Cable clam
Power cable
The LED
Green
li
hts u
. Flashing battery mark on the
dis
la
When fully charged
-1-
-4-
Closeu
of the cable clam
-2-
Linkin
cable
1
Drawmer MPA-90 User manual
A&D MPA-10000 Quick Operation Manual
Roche cobas p 480 v2 User guide
Extron electronics MPA 401-100V User manual
Kubota u15-3 Workshop Manual
Danfoss DHP-A, AL, C, H, L Installation guide
Meyer Sound LINA Operating instructions
Shibaura ST324 Specification
