Topcon KR-1W User manual

Type
User manual
USER MANUAL
WAVE-FRONT ANALYZER
KR-1W
1
INTRODUCTION
Thank you for purchasing the TOPCON Wave-front Analyzer KR-1W.
This instrument has the following features:
• The refractive power of the eye, the curvature radius of the cornea and the pupil diame-
ter can be determined by simple operations.
• By displaying the Hartmann image and Mire image, wavefront aberration measurement
of the eye can be done.
•
Auto alignment and auto start functions enabling quick measurement under best conditions
This text outlines the TOPCON Wave-front Analyzer KR-1W and describes basic opera-
tions, troubleshooting, checking, maintenance and cleaning.
To encourage the safe, efficient use of this instrument, carefully read "DISPLAYS FOR
SAFE USE" and "GENERAL SAFETY INFORMATION."
Also, keep this User Manual in a convenient location for your future reference.
PRECAUTIONS
• The patient who undergoes an examination by this instrument must maintain concentration for a
few minutes and keep to the following instructions:
• To fix the face to the chinrest, forehead rest, etc.
• To keep the eye open.
• To understand and follow instructions when undergoing an examination.
• To ensure smooth operation, install the instrument on a leveled stand free of vibrations. Also, do
not place any objects on the instrument.
• Connect all cables according to Preparation instructions on page 30.
• Use the specified source voltage.
• When not in use, turn off the power and put the measuring window cap and dust cover on.
• To ensure the correct reading, do not mar the measuring window with finger prints, dust, etc.
• Use this machine in a darkroom.
CAUTION : Federal laws restricts this device to the sale by or on the order of a physician.
2
DISPOSAL
When disposing the instrument and/or parts, follow the local regulations for disposal and recy-
cling.
STORING PLACE, USAGE PERIOD
1. When storing the instrument, ensure that the following conditions are met:
(1) The instrument must not be splashed with water.
(2) Store the instrument away from environments where air pressure, temperature, humidity,
ventilation, sunlight, dust, salty/sulfurous air, etc. could cause damage.
(3) Do not store or transport the instrument on a slanted or uneven surface or in an area
where it is subject to vibrations or instability.
(4) Do not store the instrument where chemicals are stored or gas is generated.
2. Normal life span of the instrument:
8 years from delivery providing regular maintenance is performed [TOPCON data]
USER MAINTENANCE
1.Regularly maintain and check the equipment and parts.
2.When resuming the use after a long storage time, verify that the instrument operates cor-
rectly and safely.
3.To ensure the correct reading, do not soil the measuring window with finger prints or dust.
4.If the measuring window is soiled, clean it following the "CLEANING THE INSTRUMENT"
instructions on page 180.
This symbol is applicable for EU member countries only.
To avoid potential damage to the environment and possibly human health, this instrument should be
disposed of (i) for EU member countries - in accordance with WEEE (Directive on Waste Electrical and
Electronic Equipment), or (ii) for all other countries, in accordance with local disposal and recycling
laws.
[WARNING]
Handling the cord on this product or cords associated with accessories sold with this product, will expose you to lead, a
chemical known to the State of California to cause birth detects or other reproductive harm. Wash hands after han-
dling.
This Product Contains Mercury in the backlighting of the LCD display. Prior to disposal remove of otherwise ensure that
this is disposed of in accordance with Local, State and Federal Laws. This information is applicable in U.S.A only.
This product contains a CRL Litium Battery which contains Perchlorate Material-special handling may apply.
See http://www.dtsc.ca.gov/hazardouswaste/perchlorate/
Note; This is applicable to California, U.S.A. only
3
HOW TO READ THIS MANUAL
• Read the instructions on pages 1 to 8 before using the machine.
• Regarding connection to various devices, see "PREPARATIONS" on page 30.
• If you need to see how the machine works first of all, read "BASIC OPERATIONS"(page 37)
first.
• For setting various functions, see "FUNCTION SETTING USING SETTINGS SCREEN" on
page 111.
SYMBOL IN THE TEXT
Note: contains the information of useful features to know and cautions to prevent
any problems.
4
DISPLAYS FOR SAFE USE
In order to encourage the safe use of the machine and prevent any danger to the operator and
others or damage to properties, important warnings are placed on the product and inserted in the
user manual.
We suggest that everyone understand the meaning of the following displays and icons before
reading the "
GENERAL SAFETY INFORMATION" and the main text.
DISPLAYS
Display Meaning
Ignoring or disregarding this display may lead to death or
serious injury.
Ignoring or disregarding this display may lead to personal injury
or physical damage.
• Injury refers to cuts, bruises, sprains, fractures, burn, electric
shock, etc.
• Physical damage refers to extensive damage to buildings or
equipment and furniture.
WARNINGS
CAUTIONS
NOTES
5
GENERAL SAFETY INFORMATION
Ensuring the Safety of Patients and Operators
When operating the instrument, be not touch the patient's eye or nose.
[Inform the patient accordingly]
The safety and effectiveness of the Wave-front Analyzer KR-1W has not been established for
use of the device as an accessory interfaced to the refractive laser for the treatments of the
higher order aberrations of the eye by photorefractive keratectomy (PRK), phototherapeutic
keratectomy (PTK), or laser assisted in situ keratomileusis (LASIK).
Preventing Electric Shocks and Fires.
To avoid fire and electric shock, install the instrument in a dry place free of water and other liq-
uids.
To avoid fire and electric shock, do not put cups or other containers with liquids near the instru-
ment.
To avoid electric shocks, do not insert metal objects into the instrument body through the vent
holes or gaps.
To avoid fire in the event of an instrument malfunction, immediately turn OFF the power switch
"
" and disconnect the power cord from the instrument if you see smoke coming from the
instrument, etc.
Don't install the instrument where it is difficult to disconnect the power cord from the instru-
ment. Ask your dealer for service.
WARNINGS
6
Ensuring the Safety of Patients and Operators
To avoid injury in changing the measurement mode, do not place fingers into the measuring
opening.
To avoid electric shock, do not open cover. For repair, ask a certified Topcon Service Engineer.
When changing the fuse, turn off the power, and disconnect the power cable. Use the properly
rated fuse.
Preventing Electric Shocks and burn.
To avoid injury, when moving the chinrest up/down, keep fingers away from moving parts.
When operating the instrument, be careful not to touch the patient's eye or nose.
Electromagnetic Compatibility (EMC)
This instrument has been tested (with 100/120/230V) and found to comply with IEC60601-1-2:
Ed.3.0: 2007.
This instrument may emit a radio frequency energy (within the standard) and cause an
adverse effect on the devices located nearby.
When such effect is confirmed by the ON/OFF operation, a proper treatment as to change the
direction, use another outlet, etc. is recommended. If the problem remains unsolved, call your
dealer.
CAUTIONS
7
USAGE AND MAINTENANCE
PURPOSE
USER MAINTENANCE
To ensure the safety and performance of the instrument, all maintenance work, unless speci-
fied in this manual, shall be conducted by trained service engineers.
The following maintenance tasks may be done by the user.
For details, see the relevant part of this manual.
CHANGING THE FUSE
The primary fuses for the main body may be changed by a non-trained service technician.
For details, refer to "REPLACING THE FUSE" on page 181.
DISCLAIMERS
The Wave-front Analyzer KR-1W is a precision electrical instrument for medical use
which must be used under the guidance and instructions of a doctor.
• TOPCON is not responsible for damage due to fire, earthquakes, actions or inactions of third
persons or other accidents, or damage due to negligence and misuse by the user and any
use under unusual conditions.
• TOPCON is not responsible for damage derived from inability to properly use this equip-
ment, such as loss of business profits and suspension of business.
• TOPCON is not responsible for damage caused by operations other than those described in
this User Manual.
• The device does not provide a diagnose of any condition or lack thereof or any recommen-
dations for appropriate treatment. The relevant healthcare provider is fully responsible for all
diagnose and treatment decisions and recommendations.
8
WARNING INDICATIONS AND POSITIONS
To ensure the safety, this machine provides warning displays.
Use the instrument correctly by observing the display instructions. If any of the following dis-
play labels are missing, contact your TOPCON dealer at the address listed on the back cover.
No. Label Meaning
1
WARNING
To avoid injury caused by electric shock, do not open the cover.
Ask your dealer for service.
2
WARNING
Electric shock may cause burns or a possible fire. Turn the power
switch OFF and unplug the power cord before replacing the fuses.
Replace only with fuses of the correct rating.
3
CAUTION
When operating the chinrest up/down switch, be careful not to
pinch the patient's hand.
The patient may be injured.
4
CAUTION
Be careful not to hit the patient's eyes or nose with the instrument
during operation.
5
Degree of protection against electric shock:
TYPE B EQUIPMENT
1 3 4 2 5
CLASS
I
LASER PRODUCTS
9
CONTENT
INTRODUCTION...................................................................................................1
PRECAUTIONS.....................................................................................................1
HOW TO READ THIS MANUAL............................................................................3
DISPLAYS FOR SAFE USE..................................................................................4
GENERAL SAFETY INFORMATION ....................................................................5
USAGE AND MAINTENANCE ..............................................................................7
DISCLAIMERS ......................................................................................................7
WARNING INDICATIONS AND POSITIONS........................................................8
COMPONENTS
COMPONENT NAMES........................................................................................12
COMPOSITION OF PARTS WHICH CONTACT THE HUMAN BODY...............12
OPERATION METHOD OF CONTROL PANEL..................................................13
CONTROL PANEL COMPONENTS
(EXAMINATION PURPOSE SELECTION SCREEN)..........................................14
CONTROL PANEL COMPONENTS
(SELECTION OF EXAMINATION SCREEN)......................................................15
CONTROL PANEL COMPONENTS
(MEASUREMENT SCREEN IN THE REF/KRT MODE) .....................................16
CONTROL PANEL COMPONENTS
(MEASUREMENT RESULT LIST SCREEN).......................................................18
CONTROL PANEL COMPONENTS (ANALYSIS RESULT SCREEN) ...............20
OTHER SCREEN DISPLAYS..............................................................................22
PRINTER OUTPUT.............................................................................................23
STANDARD ACCESSORIES..............................................................................29
PREPARATIONS
INSTALLING THE INSTRUMENT.......................................................................30
CONNECTING THE POWER CABLE.................................................................31
CONNECTING EXTERNAL I/O TERMINALS .....................................................32
SETTING THE PRINTER PAPER.......................................................................33
RESETTING FROM POWER SAVE STATUS....................................................35
OPERATING THE CONTROL LEVER................................................................35
BASIC OPERATIONS
SELECTION OF EXAMINATION INTERFACE AND
ARBITRARY OPERATION INTERFACE.............................................................37
OPERATION IN THE SELECTION OF EXAMINATION INTERFACE .....................39
POWER-ON AND MEASUREMENT COURSE SELECTION .............................39
PREPARATION BEFORE MEASUREMENT......................................................41
MEASUREMENT.................................................................................................43
DISPLAYING MEASUREMENT VALUES...........................................................45
CLEARING ALL MEASUREMENT VALUES.......................................................45
MEASUREMENT RESULT LIST SCREEN.........................................................47
DISPLAYING THE ANALYSIS RESULT.............................................................47
COMPLETION.....................................................................................................48
10
INDIVIDUAL OPERATIONS
OPERATION IN THE ARBITRARY OPERATION INTERFACE...............................49
MEASUREMENT MODE SELECTION................................................................49
SELECTION OF AUTO MEASUREMENT/AUTO TRACKING MEASUREMENT/
MANUAL MEASUREMENT.................................................................................50
SETTING FIXATION TARGET ILLUMINATION LEVEL......................................50
SETTING HARTMANN EXPOSURE TIME .........................................................51
MEASURING ONE EYE ONLY...........................................................................52
MEASUREMENT......................................................................................................53
PREPARATION BEFORE MEASUREMENT......................................................53
MEASUREMENT UNDER AUTO MODE............................................................54
MEASUREMENT UNDER AUTO TRACKING MODE.........................................57
MEASUREMENT UNDER MANUAL MODE.......................................................59
DISPLAYING MEASUREMENT VALUES...........................................................61
CLEARING ALL MEASUREMENT VALUES.......................................................61
TERMINATING MEASUREMENT.......................................................................62
IN A CASE LIKE THIS .............................................................................................63
TO STOP AUTO ALIGNMENT MEASUREMENT IN THE MIDDLE....................63
TO MEASURE THE RIGHT/LEFT EYE ONLY....................................................63
ALIGNMENT DOES NOT START.......................................................................64
SERIAL (DRY EYE) MEASUREMENT................................................................66
PUPILLOMETRY.................................................................................................68
DISPLAYING ALL MEASUREMENT DATA........................................................70
PRINTING MEASUREMENT VALUES ...............................................................71
INPUT/OUTPUT..................................................................................................73
DISPLAYING THE MEASUREMENT RESULT
MEASUREMENT RESULT LIST SCREEN..............................................................74
ANALYSIS RESULT SCREEN .................................................................................77
DESCRIPTION OF MAP LAYOUT......................................................................78
ENLARGEMENT DISPLAY.................................................................................94
ANALYSIS SETTING MENU...............................................................................97
TOPOMAP SMOOTHING FUNCTION................................................................99
TOPO/ABERRATION MAP OVERLAY AND MARKER OVERLAY ..................100
IOL THRESHOLD SETTING OF IOL SELECTION MAP..................................101
DESCRIPTION ABOUT MEASUREMENT RESULTS...........................................104
ANALYSIS CENTER .........................................................................................104
DESCRIPTION ABOUT RMS DISPLAY OF OCULAR ABERRATION .............104
DESCRIPTION ABOUT RMS DISPLAY OF CORNEAL ABERRATION...........105
FUNCTION SETTING USING SETTINGS SCREEN
OPERATION METHOD OF SETTINGS SCREEN............................................111
LIST OF SETUP ITEMS....................................................................................114
MEASURE (TEMPORARY SETTING)..............................................................124
INITIAL SETTING (INITIAL) ..............................................................................128
DISPLAY SETTING (DISPLAY) ........................................................................142
SETTING OF INTERNAL PRINTER (PRINT INT).............................................159
SETTING OF EXTERNAL PRINTER (PRINT EXT) ..........................................167
11
SETTING OF DATA COMMUNICATION (COMM)............................................168
LAN CONNECTION (NETWORK).....................................................................171
SETUP OF SELECTION OF EXAMINATION
MEASUREMENT
SCREENING SETTINGS ..................................................................................176
SETTING PUPILLOMETRY ..............................................................................178
SETTING SERIAL MEASUREMENT ................................................................178
SETTING CATARACT MEASUREMENT..........................................................178
SETTING OVER REF. MEASUREMENT..........................................................179
MAINTENANCE AND CHECKING
DAILY MEAINTENANCE........................................................................................180
CHECKING THE MEASURING ACCURACY....................................................180
CLEANING THE INSTRUMENT........................................................................180
PRINTER PAPER JAM......................................................................................180
REPLACING THE FUSE...................................................................................181
SPECIAL NOTE OF CLEANING............................................................................182
CLEANING THE PLACHIDO RING AND OUTER COVER...............................182
CLEANING THE MONITOR SCREEN (CONTROL PANEL) ............................182
CLEANING THE COMPONENTS TOUCHING THE PATIENT.........................182
BEFORE REQUESTING SERVICE
CHECKING OPERATIONS...............................................................................183
REFERENCES
MESSAGE LIST ................................................................................................184
DATA THAT CAN BE OUTPUT AND USABLE PRINTERS IN EACH SCREEN
..186
OPTIONAL ACCESSORIES..............................................................................187
ORDERING CONSUMABLE SUPPLIES...........................................................187
SHAPE OF PLUG..............................................................................................188
MARKS DISPLAYED OUTSIDE THE MAIN BODY ..........................................188
RS232C COMMUNICATION SPECIFICATIONS..............................................189
SPECIFICATIONS
SPECIFICATION AND PERFORMANCE..........................................................191
ELECTROMAGNETIC COMPATIBILITY ..........................................................193
DIMENSIONS AND WEIGHT............................................................................197
PURPOSE OF USE...........................................................................................197
OPERATIONS AND PRINCIPLE OF OPERATION ..........................................197
ELECTRIC RATING ..........................................................................................197
LASER ILLUMINATION SYSTEM.....................................................................197
SAFETY DESIGNATIONS PER IEC 60601-1 STANDARD..............................198
TERMINOLOGY
DESCRIPTION OF TERMS...............................................................................199
END USER LICENSE AGREEMENT...............................................................208
12
COMPONENTS
COMPONENTS
COMPONENT NAMES
COMPOSITION OF PARTS WHICH CONTACT THE HUMAN BODY
Forehead rest : Silicone rubber
Chinrest : Acrylonitrile butadiene styrene resin
Control panel
Measuring head
Chinrest up/down button
External I/O terminal
Measurement switch
Control lever
Power lamp
Printer cover open button
POWER switch
Inlet cover
Forehead rest
Measuring window
Height mark
Chinrest tissue stopper pin
Chinrest
Main body Section
Power supply Section
Chinrest Section
Placido ring
*1: Part where gets in contact with the patient: Type B
*1
*1
13
COMPONENTS
OPERATION METHOD OF CONTROL PANEL
Control panel is a touch panel performing various operations and setups by touching the
screen. It displays the information including setting conditions and measurement results as
well as observation images.
MEMO
When operating the control panel, do not use any sharp tools; e.g. ball
point pen.
Tap To select any relevant item.
Touch the screen softly with a finger.
Drag Used to change images.
(Overlay, Reduction of image size, etc.)
Touch the screen softly and move the finger.
(Example)
Enlarging the image (Method 1)
Touch the upper part of the image and drag it
upward.
Reducing the image
Touch the upper part of the image and drag it
downward.
Enlarging the image (Method 2)
Tap the image.
14
COMPONENTS
CONTROL PANEL COMPONENTS
(EXAMINATION PURPOSE SELECTION SCREEN)
This is the screen to select the measurement course provided according to the examination
purpose after turning the instrument on.
(1) SETTINGS button Used to change the setting details of each measurement course
by examination purpose.
(2) Setting conditions Displays the currently selected measurement course and its set-
ting conditions.
(3) Patient ID button The Patient ID INPUT screen is displayed. The patient ID is dis-
played on the right.
(4) Selection of examination button
Used to select the measurement course according to the exami-
nation purpose.
(5) Scroll bar If some measurement courses are not displayed, the next mea-
surement course can be displayed by dragging the scroll bar.
(6) OK button Confirms the selected measurement course and shifts to the
measurement screen.
(7) CANCEL button Cancels the change of the measurement course and returns to
the measurement screen with the setting before the change.
(8) Connection status icons
If any PCs and printers are connected to this instrument, they will
be displayed as icons.
(9) Direct exam. selection button
If checked, the screen switches to the measurement screen right
after tapping the measurement mode name.
After started, the examination purpose selection screen will not be displayed and
can be set to display the measurement screen directly instead. For more details,
refer to page
37, "SELECTION OF EXAMINATION INTERFACE AND ARBI-
TRARY OPERATION INTERFACE".
(5) Scroll bar
(7) CANCEL button
Display of patient ID
(6) OK button(9) Direct exam. selection button
(3) Patient ID button
(1) SETTINGS button
(2) Setting conditions
(4) Selection of
examination button
(8) Connection status
icons
15
COMPONENTS
CONTROL PANEL COMPONENTS (SELECTION OF EXAMINATION SCREEN)
This is the screen to select the measurement course provided according to the report after
turning the instrument on and starting it.
(1) SETTINGS button Used to change the setting details of each measurement course
by examination purpose.
(2) Report selection screen
Used to select the measurement course according to the report.
(3) Patient ID button The Patient ID INPUT screen is displayed. The patient ID is dis-
played on the right.
(4) Scroll bar If some measurement courses are not displayed, the next mea-
surement course can be displayed by dragging the scroll bar.
(5) Connection status icons
If any PCs and printers are connected to this instrument, they will
be displayed as icons.
Display of patient ID
(1) SETTINGS button
(5) Connection status
icons
(4) Scroll bar
(3) Patient ID button
(2) Report selection
screen
16
COMPONENTS
CONTROL PANEL COMPONENTS
(MEASUREMENT SCREEN IN THE REF/KRT MODE)
AUTO MEASUREMENT SCREEN
The control panel displays observation images and shows set conditions and measure-
ment results. The control panel is also used as a touch panel for performing various oper-
ations and settings.
(1) button, button Select the right/left eye. When the button is tapped, the main body
moves in the selected direction. (see page 52)
The selected R/L button is displayed in orange. (see page 52)
Continuous measurements of right and left eyes and the mea-
surement of only the right/left eye can be set.
(2) Machine No. The machine No. is displayed. This can also be hidden (see page
135).
(3) Patient ID The Patient ID INPUT screen is displayed. The patient ID is dis-
played on the right.
(4) Measurement value Measurement values of REF (S, C, A) and KRT (R1, R2, A1) are
displayed.
(5) Measurement count The measurement count each of the right/left eye is displayed.
*(4)-(5) are displayed on the right/left ends of the screen.
(6) Display of set values Displaying the current setting values including the Hartmann
exposure time, astigmatism sign and vertex distance. The
Hartmann Exposure time can be changed on this screen. (see
page
51)
(7) Function button A list of operable functions is displayed. Select the relevant button
on the touch panel. (see page
17)
(8) AUTO button/AUTO TRACKING button/MANUAL button
Measurement mode is changed for AUTO, AUTO TRACKING
and MANUAL. (see page
50)
(9) Measurement Data List button
Measurement values are displayed in list form. (see page 70)
(7) Function button
Right eye
Left eye
(4) Measurement value
(5) Measurement count
(2) Machine No.
(8) AUTO/AUTO TRACKING/MANUAL button
(6) Display of set values
(10) Fixed Target Brightness
(11) REF button,
KRT button
(3) Patient ID button
(1) R button, L button
(9) Measurement
Data List button
Display of patient ID
(12) SETTINGS button
(13) Exam purpose
shortcut button
R
L
17
COMPONENTS
(10) Fixed Target Brightness
The patient fixation target brightness can be selected. (see page
50)
(11) REF button, KRT button
If the measurement course by examination purpose is not used,
REF and KERATO continuous measurement (both REF and
KERATO buttons are lit), REF individual measurement (REF but
-
ton only is lit) and KERATO individual measurement (KERATO
button only is lit) can be set arbitrarily. (see page
49)
: REF/KRT continuous measurement
Analysis of refractive wavefront aberration and corneal
wavefront aberration can be done using the obtained
results.
: REF measurement
Analysis of refractive wavefront aberration can be done
using the obtained results.
: KRT measurement
Analysis of corneal wavefront aberration can be done
using the obtained results.
(12) SETTINGS button Various settings are available, for measuring operation, output of
measurement value data and result display format etc. (see page
111)
(13) Exam purpose shortcut button
A shortcut button to select the measurement course according to
the examination purpose.
DETAILS OF FUNCTION BUTTONS
(1) button
Moves to the examination purpose selection screen. (see page 14)
(2) button
Clears all measurement data.
(3) button
The display goes to the ANALYSIS RESULT screen. (See page 77)
(4) button
Transfers the measurement data.
(5) button
Prints the measurement results out via the built-in printer.
(1) Selection of examination button (3) ANALYZE button (5) PRINT button
(2) ALL CLEAR button (4) DATA OUT button
Selection of examination
ALL CLEAR
ANALYZE
DATA OUT
PRINT
18
COMPONENTS
CONTROL PANEL COMPONENTS (MEASUREMENT RESULT LIST SCREEN)
MEASUREMENT RESULT LIST SCREEN
On the Measurement Result List screen, a list of measurement results can be confirmed. By
selecting the data to be displayed, data output to the external PC, printing data, initial display
on the Analysis screen, and clearing data can be done.
When plural measurements are performed under Auto mode, the screen is changed automat-
ically to the Measurement Result List screen.
In the case of Manual mode or Auto Tracking mode, it is displayed by tapping the
button after the measurement.
(1) Scroll bar By scrolling the measurement result, measurement data can be
scrolled up and down.
(2) DELETE button Select the data to be deleted. The selected button
turns on in orange. Under this condition, deletion is done by tap-
ping the button of the (3)Function button.
(3) Function button Available functions are listed. Select the corresponding button on
the touch panel.
button The Measurement screen is returned and an addi-
tional measurement can be done. However, if data
are outputted to the connected PC or printed by the
internal/external printer, the display is changed to
In case of the serial measurement, the screen does not shift to the Table of mea-
surement result screen automatically after measurement completion. The Table of
measurement result screen can be displayed by tapping
button on the progress measurement map displayed with tapping of the
after measurement. In case of Pupillometry, the screen
does not go automatically to the Table of measurement result screen after finishing
the measurement.
ANALYZE
RESUL
T L
T
LIST
ANALYZE
(3) Function button
(1) Scroll bar
Right eye
Typical REF value
Typical KRT value
Selected data
(5) Recommended data
selection button
Left eye
Mire Image
Hartmann Image
(2) DELETE button
(4) Printed icon/
output icon
DELETE
DELETE
MEASURE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216

Topcon KR-1W User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI