2. Golden Lighting
  3. 7917-3P AS

Golden Lighting 7917-3P AS Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Golden Lighting 7917-3P AS Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
IMPORTANT:
• ALLINSTALLATIONWORKSHOULDBEDONEBYACCREDITEDPROFESSIONAL.
• SHUTOFFPOWERSUPPLYATFUSEORCIRCUITBREAKER!
• USEONLYTHESPECIFIEDBULBS.DONOTEXCEEDTHEMAXIMUMWATTAGE!
AssemblyInstructions:7917-3P, 6P (Whitaker)
For Customer Service, please
contact the place of purchase.
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes above. Remove
the old xture from the ceiling, including the old mounting strap.
1.Fromthepartsbagremovethemountingstrapassembly.Oneendofnipple(F)shouldbe
attachedtomountingstrap(A)withhexnutandwasher(C&D)inplace.Theotherendshouldhave
canopyloop(H)attached.Attachmountingstrap(A)tothejunctionboxusingmountingscrews(B)
andascrewdriver.Tightensecurely.
2.Unscrewcanopyloopcollar(I)fromcanopyloop(H).Passcanopy(G)overthemountedcanopy
looptotesttheheight.Approximatelyhalfofthecanopyloop’sexteriorthreadsshouldbeexposed,
andthecanopyloopcollarshouldtsnuglyontothecanopyloop.Removecanopy(G)andadjust
theheightofnipple(F)andcanopyloop(H)untilthedesiredheightisreached.Removecanopy(G)
andcanopyloop(H)andplaceaside.
ASSEMBLING THE FIXTURE
3.Centerrod(S)isonthexture’swires,butnotconnectedtothexture.Connectcenterrod(S)to
lampbody(Q)atpost(R).Pullthewiresuntiltautandpullthewiresandcenterrod(S)throughthe
centerofmetalplate(M).
4.Cables(O)maybebundledtogether.Useaknifeandcarefullycuttheplasticties.Cables(O)
havelargeheads(T)attachedtotheends.Holdheads(T)andslidecables(O)throughthehooked
holesonmetalplate(M).Whenthecablesreachthebackofthehookedholes,letheads(T)come
torestonmetalplate(M).Seethediagram.
5.Pullthewiresuntiltaut.Slidetopcap(U)downthewiresandontometalplate(M).Threadtop
cap(U)intocenterrod(S).Threadtoploop(L)downontotopcap(U)andpullthewiresuntiltaut.
FINISHING THE INSTALLATION
8.Raisecanopy(G)totheceiling.Slidecanopyloop(H)andcanopyloopcollar(I)upbeneaththe
canopy.Tightlythreadcanopyloopcollar(I)ontocanopyloop(H)tosecurecanopy(G)inplace.
9.Installlightbulbs(notincluded)inaccordancewiththexture’sspecications.Donotexceed
themaximumrecommendedwattage.
Yourinstallationiscomplete.Turnonthepowerandtestthexture.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
House Wires
Fixture Wires
Hot
CONNECTING THE WIRES
7.Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Cutawayany
excesswireaddingatleast8to10inchesofwiretothedesiredlength.Threadthexture’swires
throughcanopyloop(H)andnipple(F).Refertothewiringdiagramandattachthexture’swires
tothepowersupplywiresfromthejunctionbox.ConnectHottoHot,NeutraltoNeutral,and
GroundtoGround.Twisttheendsofthewirepairstogether,andthentwistonawireconnector.
Makesurealltwistsareinthesamedirection.Ifthereisnohousegroundwirecomingfromthe
junctionbox,locategroundscrew(E)onthemountingbracket/mountingstrapandwrapthe
xture’sgroundwirearoundthegroundscrew.Useascrewdrivertotightenthetopofground
screw(E)ontothewiresandintothemountingbracket/mountingstrap.Tuckthewiresintothe
junctionbox.
6.Bymeasuring,determinethecorrectnumberofchainlinksneededforproperhangingheight.Ifnecessary,useapairofpliers
toopenandremoveanyexcesschain(J).Attachonechainconnector(K)toeachendofchain(J).Twistthesidelocktosecurethe
connectorinplace.Connectoneofchainconnectors(K)totoploop(L)andclosethatchainconnectoraswell.Feedthexture’swires
upthroughthechain(everythreelinksorso),pullingthewiresuntiltaut.Usethefreechainconnector(K)toattachchain(J)tocanopy
loop(H).Untwistcanopyloopcollar(I)fromcanopyloop(H)toallowcanopy(G)tobeaddedtothechain.Feedthewiresupthrough
thechain.Allowcanopy(G)todropdownontothechain/wire.
NOTE: Please use the attached hexagonal spanner tool to
tighten the center rod until the cables are tight. Then double
check that the shade is straight.
/