READ these instructions before placing unit in
service. KEEP these and other materials delivered
with the unit in a binder near the Tool for ease of
reference by supervisors and operators.
Safety Instructions
Set-up Instructions
1601 J. P. Hennessy Drive, LaVergne, TN USA 37086 615/641-7533 800/688/6359 www.coatsgarage.com Manual Part No.: 85611433 00
HENNESSY INDUSTRIES INC. Manufacturer of AMMCO®, COATS® and BADA® Automotive Service Equipment and Tools. Revision: 01/19
HTS Device, Tower
Mounted & Cart Mounted
Used to assist in sealing Corvette Low
Profi le and Ultra High Performance tires.
Rear of Tire Changer
2 • COATS Hard To Seal (HTS)
Table of Contents
Important Safety Instructions .................................3
Owner’s Responsibility .........................................3
Operator Protective Equipment ............................3
Definitions of Hazard Levels .................................3
Attention - Cell Phone Warning ...............................4
HTS Tower and Cabinet Parts List ...........................5
Tower Mounting Instructions ..................................6
Tools Needed ........................................................6
Left Tower Mounted Models .................................7
Right Tower Mounted Models ...............................8
Cabinet Mounting Instructions ...............................9
Left Cabinet Mount Models ................................ 10
Right Cabinet Mount Models .............................. 11
HTS Installation
Without Water Separator .................................... 12
With Water Separator .......................................... 19
HTS Installation - on APX Tire Changer ................24
HTS Mobile Cart
Device Connection ..............................................25
Read entire manual before assembling,
installing, operating, or servicing this
equipment.
NOTICE
COATS Hard To Seal (HTS) • 3
Safety Instructions
Owner’s Responsibility
To maintain machine and user safety, the responsibility
of the owner is to read and follow these instructions:
• Follow all installation instructions.
• Make sure installation conforms to all applicable
Local, State, and Federal Codes, Rules, and
Regulations; such as State and Federal OSHA
Regulations and Electrical Codes.
• Carefully check the unit for correct initial function.
• Read and follow the safety instructions. Keep them
readily available for machine operators.
• Make certain all operators are properly trained,
know how to safely and correctly operate the unit,
and are properly supervised.
• Allow unit operation only with all parts in place and
operating safely.
• Carefully inspect the unit on a regular basis and
perform all maintenance as required.
• Service and maintain the unit only with authorized
or approved replacement parts.
• Keep all instructions permanently with the unit
and all decals/labels/notices on the unit clean and
visible.
• Do not override Secondary Button safety feature.
• Optimal Operating Pressure - 120-140 PSI.
• Always assume HTS Sealing Device is pressurized
while handling.
NOTE: Stop use and immediately remove from service
any unit that has experienced damage.
NOTE: Only apply pressure to the Mobile Cart version
at the time of use. Disconnect and drain All Air Pressure
from cart when not in use through the foot-operated
drain valve.
Operator Protective Equipment
Personal protective equipment helps make tire
servicing safer. However, equipment does not take the
place of safe operating practices. Always wear durable
work clothing during tire service activity. Loose fitting
clothing should be avoided. Tight fitting leather gloves
are recommended to protect operator’s hands when
handling worn tires and wheels. Sturdy leather work
shoes with steel toes and oil resistant soles should be
used by tire service personnel to help prevent injury in
typical shop activities. Eye protection is essential during
tire service activity. Safety glasses with side shields,
goggles, or face shields are acceptable. Back belts
provide support during lifting activities and are also
helpful in providing operator protection. Consideration
should also be given to the use of hearing protection if
tire service activity is performed in an enclosed area, or
if noise levels are high.
Definitions of Hazard Levels
Identify the hazard levels used in this manual with the
following definitions and signal words:
DANGER
Watch for this symbol:
It Means: Immediate hazards, which will result in
severe personal injury or death.
WARNING
Watch for this symbol:
It Means: Hazards or unsafe practices, which could
result in severe personal injury or death.
CAUTION
Watch for this symbol:
CAUTION
It Means: Hazards or unsafe practices, which may
result in minor personal injury or product or property
damage.
Watch for this symbol! It means BE ALERT! Your
safety, or the safety of others, is involved!
4 • COATS Hard To Seal (HTS)
This device is for use ONLY with Hard To SEAL,
DOT Approved Automotive and Light Truck tires only!
NOTE: Do Not point or activate device unless against valve hole in rim.
Do Not point while secondary button is activated unless against valve rim hole.
Do Not point at self or others.
No Cell Phone Use
or Texting
While Operating
This Device
This Device is a Powerful Tool
and requires your full attention
to prevent accidents, any of
which can result in serious
injury or death
ATTENTION
COATS Hard To Seal (HTS) • 5
HTS Tower/Cabinet Mount Models - Parts List
1
23
4
5
6
7
NON-SALEABLE
9
NON-SALEABLE
NON-SALEABLE
11
1 85611422 Muer
2 8561106804 Replaceable Nozzle PKG
3 85611400 Puller Cable Kit
4 85611490 Inator Hose
5 85611318 Warning Decal
6 8182221 6” Clamp
7 85610628 8-32 Lock Nut
8 85606390 3/4 NPT Elbow Fitting
9 920615 8-32 x .375 BHCS Screw
10 85611509
11 85611510
12 85610716
13 8182178
14 8184652
15 85611502
16 85009958
17 85606333
18 85606363
12
13
14
15
16
17
8
NON-SALEABLE
18
/05&*OTUBMMXBTIFST
CFUXFFOQMBUFBOEDMJQT
1
1
856
Clips, 3pc PKG
Holster PKG
5/16-18 x 5/8 HHCS Screw
5/16-18 Whiz Lock Hex Nut
Adjustable Regulator Nut
Regulator Assembly
3/4NPTF X 3/4 NPTM TFF FJUUJOH
3/4 NPT Nipple Fitting
*UFN 1BSU/VNCFS %FTDSJQUJPO *UFN 1BSU/VNCFS %FTDSJQUJPO
16mm Hose Clamp
.BOVBM4UPSBHF4MFFWF
/ZMPO$BCMF5JF
3JWFU-BSHF
)PMEFS$MJQ
)PMTUFS-)
4DSFXY4FMG5BQJOH
.PVOUJOH1MBUF
5PXFS.PVOUJOH3BJM
$BCJOFU.PVOUJOH3BJM
3JWFU4NBMM
1MBTUJD8BTIFS
)PMTUFS3)
*OGMBUFS3FHVMBUPS#SBDLFU
3
6 • COATS Hard To Seal (HTS)
Tower Mounted Models
1. Select mounting Tower Mounting Rails (85611476) based on customer preference.
2. Determine RH / LH orientation based on customer preference.
3. Use 4 Large Rivets (85610631) to secure the selected rails to rear side of Plate.
4. Install Holster (LH 85611462, RH 85611492) on Plate (85611475) using 5 Small Rivets
(85611484).
5. Use 3 Screws (85611463) and 3 Plastic Washers (85611488) to install 3 Clips (85611447)
to plate in orientation shown on exploded view.
6. Feed the 6” Hose Clamp (8182221) through Rail slot. Position the Plate on back of Tower
42” from floor and tighten clamp to secure, ensuring clamp falls in provided space on
tower decal. (see pages 7 and 8)
7. Using Cable Tie (8120441), attach Manual Storage Sleeve (85611436) to the plate using
the lower open hole. Insert the Operator’s Manual.
8. Store Device in Holster when not in use.
Tools Required
• Rivet Tool and 2 size tips
• #2 Phillips Screwdriver
• Tape Measure
COATS Hard To Seal (HTS) • 7
Left Tower Mounted Models
/05& CLAMP MUST FALL WITHIN ACCESSORY
CLAMP SPACE PROVIDED ON TOWER DECAL.
IF ANOTHER ACCESSORY IS ALREADY USING THIS SPACE,
CLAMP BELOW TOWER DECAL.
85611475-PLATE
(NON-SALEABLE)
MAX 42"
FROM GROUND
8182221-CLAMP
85611476-RAIL
(NON-SALEABLE)
85611476-RAIL
(NON-SALEABLE)
*OTUBMM%PDVNFOU4MFFWFXJUI
0QFSBUPShT.BOVBMVTJOH
$BCMF5JF
/05& 4QBSF3FQMBDFNFOU/P[[MFTNBZCFTUPSFEJOQSPWJEFEDMJQT
8 • COATS Hard To Seal (HTS)
Right Tower Mounted Models
NOTE: CLAMP MUST FALL WITHIN ACCESSORY
CLAMP SPACE PROVIDED ON TOWER DECAL.
IF ANOTHER ACCESSORY IS ALREADY USING THIS SPACE,
CLAMP BELOW TOWER DECAL.
85611475-PLATE
(NON-SALEABLE)
MAX 42"
FROM GROUND 8182221-CLAMP
85611476-RAIL
(NON-SALEABLE)
85611476-RAIL
(NON-SALEABLE)
*OTUBMM%PDVNFOU
4MFFWFXJUI
0QFSBUPShT.BOVBM
VTJOH$BCMF5JF
/05& 4QBSF3FQMBDFNFOU/P[[MFTNBZCFTUPSFEJOQSPWJEFEDMJQT
COATS Hard To Seal (HTS) • 9
Cabinet Mounted Models
1. Select Cabinet Mounting Rails (85611477) based customer preference.
2. Determine RH / LH orientation based on customer preference.
3. Use 4 Large Rivets (85610631) to secure the selected rails to rear side of Plate.
4. Install Holster (LH 85611462, RH 85611492) on Plate (85611475) using 5 Small Rivets
(85611484).
5. Use 3 Screws (85611463) and 3 Plastic Washers (85611488) to install 3 Clips (85611447)
to plate in orientation shown on exploded view.
6. Align the Plate on the Cabinet rear, 42” off floor, and 1” in from Tower Side of Cabinet.
(see pages 10 and 11).
7. Using hole in the rail as a template, drill one corner hole into the Cabinet using a 3/16”
drill bit. (remove any burrs created by drilling) Install Screw (920615) and Nut (85610628)
to secure the Plate to the Cabinet.
8. Using rails as a template, level the Plate and drill 3 remaining holes. (remove any burrs
created by drilling) Finish installing 3 Screws (920615) and 3 Nuts (85610628).
9. Using Cable Tie (8120441), attach Manual Storage Sleeve (85611436) to the Plate using
the lower open hole. Insert Operator’s manual.
10. Store Device in Holster when not in use.
Tools Required
• Rivet Tool and 2 size tips
• #2 Phillips Screwdriver
• Tape Measure
• Adjustable Wrench
• Pipe Wrench
• 7/8” and 1 1/16” Wrenches
10 • COATS Hard To Seal (HTS)
Left Cabinet Mount Models
'30.$"#*/&5&%(&
508&34*%&
5010'$"#*/&5
1-"5&
/0/4"-&"#-&
94$3&8#)$4
94$3&8#)$4
#"$,0'$"#*/&5
."9
'30.(306/%
'30/50'$"#*/&5
/65
3"*-
/0/4"-&"#-& 3"*-
/0/4"-&"#-&
*OTUBMM%PDVNFOU4MFFWFXJUI
0QFSBUPShT.BOVBMVTJOH
$BCMF5JF
/05&4QBSF3FQMBDFNFOU
/P[[MFTNBZCFTUPSFEJO
QSPWJEFEDMJQT
COATS Hard To Seal (HTS) • 11
Right Cabinet Mount Models
'30.$"#*/&5&%(&
508&34*%&
1-"5&
/0/4"-&"#-&
94$3&8#)$4
94$3&8#)$4
#"$,0'$"#*/&5
."9
'30.(306/%
'30/50'$"#*/&5
/65
3"*-
/0/4"-&"#-&
3"*-
/0/4"-&"#-&
5010'$"#*/&5
*OTUBMM%PDVNFOU4MFFWF
XJUI0QFSBUPShT.BOVBM
VTJOH$BCMF5JF
/05&4QBSF3FQMBDFNFOU
/P[[MFTNBZCFTUPSFEJO
QSPWJEFEDMJQT
12 • COATS Hard To Seal (HTS)
HTS Installation - Without Water Separator
1. Remove side panel. Pull Air supply hose out of Chassis side.
2. Measure supply hose 22” as shown and cut hose.
CAUTION
Always DISCONNECT the AIR SUPPLY before servicing equipment.
This prevents accidental movement of systems operated by
compressed air which may result in personal injury.
BLEED THE AIR SYSTEM by actuating all the valves.
Always DISCONNECT the ELECTRICAL POWER before servicing
equipment. This prevents electrical shock or accidental movement of
the systems operated by the electrical power.
CAUTION
COATS Hard To Seal (HTS) • 13
3. Install a Hose Clip (85606363) on hose. Hold the Pressure Regulator (85611502) as shown and press
the hose onto outter fitting.
4. Release the Clip to secure the hose.
14 • COATS Hard To Seal (HTS)
5. Uncoil the spare hose from the installation kit.
6. Cut this hose to 22” length.
COATS Hard To Seal (HTS) • 15
7. Install Hose Clip on hose.
Hold the Pressure Regulator as shown and press the hose onto inlet fitting.
Release the Clip to secure the hose.
8. Use a utility knife to cut the old supply hose approximately 1”, taking care not to score barbs.
Remove the quick disconnect fitting.
16 • COATS Hard To Seal (HTS)
9. Install Hose Clip on inlet supply hose.
Hold the quick disconnect as shown and press on the inlet supply hose.
Release the Clip to secure the hose.
10. Insert two Screws (85610716) through Chassis holes and Install Bracket (85611504).
Slide the Bracket to the right, install Nuts (8182178) and use two 1/2” wrenches to tighten.
COATS Hard To Seal (HTS) • 17
11. Install regulator as shown.
Carefully thread the Adjustable Regulator Nut (8184652) to secure the Regulator.
12. Route the supply hose out through the Chassis slot toward the back of the machine.
NOTE: Ensure that ALL hoses are routed without kinks and there is no interference
with BL Cylinder movement..
18 • COATS Hard To Seal (HTS)
13. Unscrew the manifold from the top of the Tower and set aside.
Apply thread sealant on male Tee Fitting (85009958) threads and thread it into the Tower.
Apply thread sealant on the Nipple Fitting (85606333) threads and thread it into the Tee Fitting.
Apply thread sealant on the Nipple Fitting end and thread the Elbow Fitting (85606390) on it.
(exiting downward)
Apply thread sealant on the Inflator Hose (85611490) fitting and thread it into the Elbow Fitting.
Apply thread sealant to Manifold and reinstall into top tee fitting port.
NOTE: This completes the HTS device installation only.
14. Connect Inflator Hose fitting to the Device fitting and use a 7/8” wrench and 1 1/16” wrench to tighten.
HTS only installed
HTS Installation - Without existing ABS Device
COATS Hard To Seal (HTS) • 19
1. Remove Chassis side panel.
Remove the two Screws securing Water Seperator.
Cut outlet hose from Water Seperator where shown.
2. Route cut hose back through Chassis and out side.
Use a utility Knife to remove the piece of hose from the Water Separator inlet fitting, taking care
not to score barbs..
HTS Installation - With Water Separator
CAUTION
Always DISCONNECT the AIR SUPPLY before servicing equipment.
This prevents accidental movement of systems operated by
compressed air which may result in personal injury.
BLEED THE AIR SYSTEM by actuating all the valves.
Always DISCONNECT the ELECTRICAL POWER before servicing
equipment. This prevents electrical shock or accidental movement of
the systems operated by the electrical power.
CAUTION
20 • COATS Hard To Seal (HTS)
3. Install Hose Clip on hose going into the Chasis.
Hold the Pressure Regulator as shown and press the hose onto outlet fitting where shown.
Release the Clip to secure the hose.
4. Measure and cut the spare hose from kit to 22” length.
Install Hose Clip on this hose.
Hold the Pressure Regulator as shown and press the hose onto inlet fitting where shown.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
Coats HTS Bead Sealer Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Coats Kit 85000675, Air Inflator Operating instructions
-
-
-
-
-
-
-
-
-
Other documents
-
DriSteem VAPORMIST Installation, Operation and Maintenance Manual
-
Dometic HTS-VG, HTS-T, HTS-Basic Series Holding Tanks Installation guide
-
DriSteem Vaporstream VLDI 5-1 Installation, Operation and Maintenance Manual
-
Jackson DishStar HT Installation, Operation And Service Manual
-
DriSteem HUMIDI-TECH Specification
-
DriSteem STS Installation, Operation and Maintenance Manual
-
Electrolux 5995615357 User manual
-
-
Electrolux EN18WI30LS User manual
-
Jackson / Dalton Dishwasher JPX-300HN User manual
