Bear chair BC201 Operating instructions

Brand
Bear chair
Model
BC201
Type
Operating instructions
INSTRUCTIONS KIT BEAR CHAIR BC201
1.
2.
3.
4. 5.
5.
6.
8.
8.
4.
3.
4.
9.
11.
12.
13.
7.
14.
10.
1.
Parts list:
NR. parts Quanty
1. Legs 2
2. Seat slats 6
3. Arm support 2
4. Triangles 2
5. Arms 2
6. Additional Arm Support 2
7. Struts 2
8. Sides , left (L) en right (R) 2
9. Bottom Back Support 1
10. Back Slats 7
11. Top Back Support 1
12. Frontm Slat 1
13. Comfort Slat 1
14. Plated Screws 68
14. Brass Plaque 1
Note:
Put any loose parts ordered on the ground and check the numbers! Shed there, where necessary,
rough parts are smooth. Check before you glued, or glueing the right parts.
Read the installation requirements before you begin. Good luck with the installation!
Bear chair Nederland
Postbus 500
3700 AM Zeist
Original Bear Chair BC201
Set the bottom back support (9) and top back support (11)
on a at surface with the curved sides and countersunk holes
facing up. Arrange the seven back slats (10) with the longest
in the centre, on the supports.
9.
11.
10.
step 1.
Push al the slats together so that there is even spacing on
each side. Screw only the centre slat down using screws in
the pre-drilled holes*
*Before tightening has screwed this slats, rst apply a very
thin layer of glue (Tec7) in the middle of the bar screwing.
step 2.
Space the slats out evenly, from the centre attached slat, so
that the shortest outside slats are even with end of the curve
on the back supports, and then attach.
Use a thin slat as a template. When the top is nice and round,
you can the slats glued (Tec7) and screw.
step 3.
Attach the legs (1) to the sides (8) using four screws in the
pre-drilled holes as shown. Line up the screws with the pilot
holes on the leg. Each leg and side are marked either “L” for
le and “R” for right, and should be matched together.
step 4.
8.
1.
8.
1.
Place the two sides (8) marked “L” and “R” facing each other
with the legs on the outside. e “R” should be on the right
side of the chair (as sitting) Attach the front slat (12) to the
front of the sides as shown. Using four screws and use Tec7.
step 5.
8.
8.
12.
Place back assembly into the cut out area on the sides as
shown, attach with two screws through the pre-drilled holes.
Don’t forget Tec7!
step 6.
Look carefully before you x anything!
Place the comfort slat (13) and six seat slats(2) on the sides
as shown in the picture, and space out evenly, leaving a small
gap between the comfort slat and the back assembly.
step 7.
2.
13.
2.
Attach each arm support(3) to the tops of the legs with
two screws. Push a triangle (4) into the right angled corner
(lining up the two pre-drilled holes in the leg and the centre
pre-drilled hole on the arm support) and attach with three
screws. Repeat on the other side. Use Tec7.
step 8.
3.
4.
Attach the top of the struts (7) to the underside of the top
back support (11) with two screws in the pre-drilled holes.
If the back assembly is noticeably leaning o centre, grasp it
rmly and move it le or right until the bottom of the struts
can be attached without twisting or bending them. Attach the
bottom of the struts to the sides with one screw each for now.
Do not apply glue here yet.
step 9.
7.
7.
Attach the back of the arm (5) to the strut with one screw
through the pre-drilled hole on the strut. Attach the front
of the arm to the arm support (3) with two screws from the
under side.
step 10.
First drill a hole with 3 mm wood drill bit Use glue Tec7!
Place the chair on a at surface and make sure it is sitting
solid on both legs and both sides. If it is not sitting at,
remove the single screw holding the bottom of the strut
down and move the strut up or down to compensate. When
the adjustments are done, attach the struts with two screws
each (and glue Tec7).
step 11.
Attach the additional arm support (#6) to the inside of the
struts, underneath the back of the arms through the pre-dril-
led holes with four screws.
Pre-drill with a wood drill bit (3 mm) is recommended.
step 12.
6.
Knock the caps under the legs and t the brass plate on the
front of the chair.
step 13.
Remove any adhesive from the chair and sanding rough parts
smooth. Your seat is ready for use.
step 14.
Zet op vlakke ondergrond
Enjoy your Bear chair
ALWAYS CHECK THE LOOSE PARTS :
You have purchased a kit of the BC201 . is kit box packed with care . If, aer the
checking nevertheless appear that parts are missing or damaged , please within 7 days, preferably by email to
contact us . If necessary, take photos and send it along .
We will contact you as soon as possible .
You have chosen a kit box . e supplier is responsible for the supplied loose
parts. You are responsible for assembling !
Use only the screws ! ese are made of stainless steel and do not rust .
Use only a Canadian Bitje , guaranteed to turn the screws otherwise broken.
Use for bonding only Tec7 . is adhesive is suitable for indoor and outdoor use . In all weathers . Always
bonding portion light rub , not both parts !
Cedar wood is light and delicate. So beware of dents . Tighten the screws . But beware : xed is xed !
If you follow the above steps carefully , you can mount the seat in a good way . We wish you much fun with the
bear chair , and refer to service to our website .
team of Bear chair Europe
Conditions of self-assembly.
Bear chair Nederland
Postbus 500
3700 AM Zeist
info@the-bearchair.nl
www.the-bearchair.nl
0343-513741
11.
6.
7.
3 mm drill Canadian bitjeµ
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Bear chair BC201 Operating instructions

Brand
Bear chair
Model
BC201
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents