Page is loading ...
InstallatIon GuIde
699-7800 Keypad Deskstand
Description
The 699-7800 Keypad Deskstand is a mounting stand congured for all DMP 7800 Series keypad models. The
699-7800 is constructed of smoked plexiglass and provides a sturdy keypad mounting option for any location.
Designed to provide access to all DMP keypad wiring headers allows quick and easy keypad wire connections.
What is Included
• 699-7800 Keypad Deskstand
• Wiring Block
• Wire Harness 10 ft.
• 4 round-head Phillips screws
• Tie Wrap
Mounting Keypads
Standard Keypad Mounting
Use the round head Phillips screws to mount the keypad base to the 699-7800 Deskstand. Refer to Figure 1
as needed.
1. Refer to the keypad installation guide and remove the cover, with circuit board and components attached, from
the keypad base.
2. Align the keypad base to the four keypad mounting holes on the 699-7800 Deskstand.
3. Insert the screws through the keypad base and 699-7800 Deskstand.
4. Use a Phillips head screwdriver to tighten the four screws into place. Do not overtighten.
Wire Harness wire tie
strain relief mounting
holes located in
Deskstand base.
Premounted feet (4 places)
Deskstand Front View
Deskstand Side View
Graphic Touchscreen Keypad
on 699-7800 Deskstand
Keypad
mounting
hole.
Keypad wiring
harness
openings.
Keypad
mounting
hole.
Keypad
mounting
hole.
Keypad
mounting
hole.
DISARMED
NOW
TUE
Panic
Chime
Check-in
Fire Reset
MON 5:35 AM
Figure 1: 699-7800 Keypad Deskstand
Wiring
Panel to Wiring Block Connections
The wiring block can be mounted on a wall near the baseboard, or other unobtrusive location.
1. Insert a at head screwdriver into the slot on each side of the wiring block to remove the cover.
2. Remove the Phillips head screws from inside the wiring block. Use either the provided Phillips head screws or
square of double stick tape to mount the wiring block.
3. Connect the Red, Yellow, Green, and Black wires from Panel Terminals 7, 8, 9, and 10 to the wiring block as
shown in Figure 4.
4. Snap the wiring block cover back into place.
5. Plug the modular plug end of the 10 ft. wire harness into the wiring block modular receptacle.
800-641-4282
www.dmp.com 2500 North Partnership Boulevard
LT-1312 © 2013 Digital Monitoring Products
13295
Wiring Block to Keypad Connections
As needed, refer to the 7800 Series Keypad installation guide (LT-1162).
1. Run the 10 ft wire harness through the opening in the 699-7800 Deskstand and keypad base.
2. Plug the terminal end onto the right edge of the 12-pin header in the back of the keypad (J5).
3. Snap the keypad cover onto the base.
Keypad Rear Connections
Figure 3 shows the 699-7800 Deskstand rear view with the 4-wire connector plugged into the right side of the 12-pin
header. Run a tie wrap through the back or base of the 699-7800 Deskstand. Roll the excess length of the 10 ft. wire
harness into a loop and use the tie wrap to hold it in place.
B
K
R
D
Y
L
G
R
B
L
O
R
S
L
B
R
WH
To Panel Terminal 7 - Red
To Panel Terminal 8 - Yellow
To Panel Terminal 9 - Green
To Panel Terminal 10 - Black
Black Yellow
Red Green
Modular
Receptacle
Mounting
holes
(2 places)
Cover
Removal
Slot
(2 places)
Figure 4: Wiring Detail
4-wire
connector
plugged
into keypad
12-pin header.
Deskstand Rear View
To Wiring Block 10 ft. Wire Harness tie wrap strain relief
mounting holes located in Deskstand base.
Figure 3: 699 Backplate Rear View
RED YEL GRN BLK
7 8 9 10
XT30/XT50
XR100/XR500
XR150/XR350/XR550
Panel
Terminals 7-10
7800 Keypad on
699-7800 Deskstand
DISARMED
NOW
TUE
Panic
Chime
Check-in
Fire Reset
MON 5:35 AM
B
K
R
D
Y
L
G
R
B
L
O
R
S
L
B
R
WH
Black Yellow
Red Green
Mounting
holes
(2 places)
Wiring
Block
Modular
Receptacle
Figure 2: Panel to Keypad Wiring
Specications
Dimensions 5.78" W x 4.62" H x 5" D
Material Plexiglass
Compatibility
The 699-7800 Keypad Deskstand is compatible with
all 7800 Series Keypad models.
/
