Focal Point ID+ 4.5" Downlight Trimless FLC4D-RT Installation guide

Brand: Focal Point

Model: ID+ 4.5" Downlight Trimless FLC4D-RT

Type: Installation guide

This manual is also suitable for

ID+ 4.5" Wall Wash Trimless FLC4W-RT

IS0607 REV. B 2018 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 1 of 4

id+ 4.5” round trimless housing

FLC4D-RT | FLC4W-RT

Luminaires must be installed by a qualied electrician (check with local and national codes for proper installation).

To prevent electrical shock, disconnect electrical supply before installation or servicing.

non-emergency - thermally protected, non-ic

LUMINAIRE MUST BE INSTALLED PRIOR TO DRYWALL CEILING.

emergency - integral test switch

Flc4d-rt | Flc4w-rt

cp - emergency/non-emergency

Flc4d-rt | Flc4w-rt

key

power oFF power on

level attention

see additional instructions

bar hangers

sold separately

WALL WASH ORIENTATION

WALL

5 3/4” min

6 1/4” max

TO SET CEILING

THICKNESS SEE FOCAL

POINT INSTRUCTION SHEET

IS0609

3WOOD STUDS

2b x4

2a x4

IS0607 REV. B 2018 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 2 of 4

Fixtures must be installed by a qualied electrician (check with local and national codes for proper installation).

To prevent electrical shock, disconnect electrical supply before installation or servicing.

make electrical connections

METAL STUDS

MUD-IN

DO NOT REMOVE DUST

COVER UNTIL TAPE AND

MUD-IN COMPLETE

5 3/4” min

6 1/4” max

CLEAN CEILING SURFACE FREE

OF DUST AND DEBRIS

REMOVE ADHESIVE BACKING FROM MUD RING

USE DUST COVER TO ALIGN MUD RING

WITH HOUSING

MUD TAPE

DRYWALL

IS0607 REV. B 2018 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 3 of 4

Fixtures must be installed by a qualied electrician (check with local and national codes for proper installation).

To prevent electrical shock, disconnect electrical supply before installation or servicing.

WOOD CEILING

wood ceiling installation kit parts list

5/16" miniature

rabbeting bit with

1/16" cut depth

wood routing jig

3m command poster strip

#136 (qty. 40)

2 3

ADHERE COMMAND POSTER STRIPS

TO WOOD ROUTING JIG

ADHERE WOOD ROUTING JIG

TO WOOD CEILING SURFACE 4CREATE STARTER HOLE

4”

CLEAN WOOD CEILING SURFACE

AND WOOD ROUTING JIG FREE

OF DUST AND DEBRIS

.065”

Trim Recess

8a 9

CREATE TRIM RECESS

USING RABBETING BIT

SET DEPTH OF RABBETING BIT

USE TRIM TO DOUBLE CHECK DEPTH

5CREATE MAIN HOLE USING

WOOD CEILING JIG AS GUIDE 6REMOVE WOOD ROUTING JIG

FROM WOOD CEILING SURFACE 7

INSTALL 5/16" MINIATURE RABBETING BIT

WITH 1/16" CUT DEPTH

Contractor is responsible for adequately reinforcing walls and/or ceilings to support xture weight. Focal Point, LLC accepts no responsibility for inadequately reinforced walls and/or

ceilings. The information contained in this drawing is the sole property of Focal Point, LLC. Any reproduction in part or whole without the written permission of Focal Point, LLC

is prohibited.

DRIVER SERVICE

EMERGENCY - INTEGRAL TEST SWITCH

DO NOT MATE CONNECTOR

UNTIL INSTALLATION

IS COMPLETE AND A.C.

POWER IS SUPPLIED

A B

BATTERY UNIT CONNECTOR INSIDE

SEE BATTERY

MANUFACTURER

INSTRUCTIONS