Broadcom BCM953158R Quick start guide

Broadcom
Brand
Broadcom
Model
BCM953158R
Type
Quick start guide
Broadcom Confidential 953158R-IG100
October 10, 2017
BCM953158R
Quick Start Guide
Installation Guide
Broadcom, the pulse logo, Connecting everything, Avago Technologies, Avago, and the A logo are among the trademarks
of Broadcom and/or its affiliates in the United States, certain other countries and/or the EU.
Copyright © 2017 by Broadcom. All Rights Reserved.
The term “Broadcom” refers to Broadcom Limited and/or its subsidiaries. For more information, please visit
www.broadcom.com.
Broadcom reserves the right to make changes without further notice to any products or data herein to improve reliability,
function, or design. Information furnished by Broadcom is believed to be accurate and reliable. However, Broadcom does
not assume any liability arising out of the application or use of this information, nor the application or use of any product or
circuit described herein, neither does it convey any license under its patent rights nor the rights of others.
Broadcom Confidential 953158R-IG100
3
BCM953158R Installation Guide Quick Start Guide
Table of Contents
1 Introduction..................................................................................................................................................................4
2 System ..........................................................................................................................................................................5
2.1 Power...................................................................................................................................................................5
2.2 Memory – SPI Flash ............................................................................................................................................5
2.3 Console – UM Mode............................................................................................................................................5
2.4 GUI – WM Mode..................................................................................................................................................6
3 Debug Interface............................................................................................................................................................7
3.1 UART–J3408 .......................................................................................................................................................7
3.2 SPI–J1601 ...........................................................................................................................................................8
3.3 JTAG–J2302........................................................................................................................................................9
4 LED Behavior and Definitions...................................................................................................................................10
Revision History............................................................................................................................................................ 11
Broadcom Confidential 953158R-IG100
4
BCM953158R Installation Guide Quick Start Guide
1 Introduction
The BCM953158R is a reference design board for the small-package series of the BCM5315X/BCM5316X. The
configuration is eight GB copper ports and two 10 GB fiber ports. The operation mode supports UM and ROBO-OS
depending on the SPI-Flash size. The reference board is shown in Figure 1.
Figure 1: Reference Board
Power jack (+12VDC/1A)
SPI connector for debug
UART connector for
debug (PIN 1:3 3.3V/Pin
3: RX/Pin 4: GND)
Reset button
8 GB copper ports
2-10 GB Fibre ports
JTAG connector
for debug
Broadcom Confidential 953158R-IG100
5
BCM953158R Installation Guide Quick Start Guide
2 System
2.1 Power
12VDC/1A (2.5 mm), the power adapter of the SVK board (BCM953158K/BCM953162K) is available as well.
2.2 Memory – SPI Flash
U1901: MX25L8035EM1I-10G (8 Mbit by default for UM mode only)
To run the WM (ROBO-OS), the SPI-Flash requires 8 MB.
2.3 Console – UM Mode
Figure 2 shows an example of the console – UM Mode.
Figure 2: Console – UM Mode
Use the "s" and "g" commands in the CMD environment to read/write the register of chip.
Broadcom Confidential 953158R-IG100
6
BCM953158R Installation Guide Quick Start Guide
2.4 GUI – WM Mode
The default IP for GUI access is 192.168.1.10. Figure 3 shows the GUI screen.
Figure 3: GUI – WM Mode
Broadcom Confidential 953158R-IG100
7
BCM953158R Installation Guide Quick Start Guide
3 Debug Interface
The debug interface is described in the following sections.
3.1 UART–J3408
Figure 4: UART–J3408
To access the UART console interface, connect the TTL to UART transceiver module as shown in Figure 5 (such as the
RS232 To TTL converter module serial module DB9 connector). Do not use a USB-to-TTL cable to connect to the board
directly. It may cause chip damage due to incorrect power rail or surge issues.
Figure 5: Connecting the TTL to UART Transceiver Module
NOTE: The baud rate of the UART is 9600.
Table 1: UART-J3408 Pin Descriptions
Pin 1 2 3 4
Function 3.3V MFIO0_UART_RXD MFIO1_UART_TXD GND
UART-J3408
Broadcom Confidential 953158R-IG100
8
BCM953158R Installation Guide Quick Start Guide
3.2 SPI–J1601
Figure 6: SPI–J1601
Note: The J1601 header is connected to the BCM53158 SPI1 master interface by a default board BOM option (R9839,
R9840, R9841, and R9842 are all installed with a 0-ohm resistor in their position A–C only). To connect the BCM53158 SPI2
slave interface to J1601, install a 0-ohm resistor only in position B–C of R9839, R9840, R9841, and R9842.
Table 2: SPI Pin Descriptions
Pin 1 2 3 4 5 6
Function 3.3V SCK MOSI SS MISO GND
SPI-J1601
Broadcom Confidential 953158R-IG100
9
BCM953158R Installation Guide Quick Start Guide
3.3 JTAG–J2302
Figure 7: JTAG–J2302
Broadcom Confidential 953158R-IG100
10
BCM953158R Installation Guide Quick Start Guide
4 LED Behavior and Definitions
Figure 8 provides the locations for the LED indicators.
Figure 8: LED Locations
Table 3 provides the LED behaviors and definitions.
Table 3: LED Behavior and Definitions
Situation Link Status LED Activity LED
No link Off Off
Link, but no traffic Green lit Off
Link with traffic Green lit Green blinking
Link status
Activity
Broadcom Confidential 953158R-IG100
11
BCM953158R Installation Guide Quick Start Guide
Revision History
953158R-IG100; October 10, 2017
Initial release.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Broadcom BCM953158R Quick start guide

Broadcom
Brand
Broadcom
Model
BCM953158R
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents