ACT ACTPRO MIFARE DESFIRE EV1 1050 Operating instructions

Brand: ACT

Model: ACTPRO MIFARE DESFIRE EV1 1050

Type: Operating instructions

This manual is also suitable for

Operating & Installation Instructions for

ACTpro MIFARE DESFire EV1 Readers

18-00072

ACTpro DESFIRE EV1 Operating and Installation Manual Rev 1.0

Contents

Introduction:aboutMIFAREDESFireEV1 ___________________________________________________ 1

ImportantInstallationNotes _____________________________________________________________ 1

OrderingInformation___________________________________________________________________ 1

ReaderOutputDataFormat _____________________________________________________________ 2

WiringInformationfor“Clock&Data”Output ____________________________________________________ 2

WiringInformationfor“Wiegand”Output _______________________________________________________ 3

ReaderConfiguration___________________________________________________________________4

Operation:ACTproMIFAREDESFireEV11030PM/1040/1050 ______________________________________ 4

Operation:ACTproMIFAREDESFireEV11030 _____________________________________________________ 4

BacklightOperation ____________________________________________________________________ 5

StatusLEDoperationonACTproMIFAREDESFireEV11030PMreaderonly _______________________ 5

ReaderInputs _________________________________________________________________________ 5

PowerOnBeepCodes __________________________________________________________________ 5

InstallationdiagramforDESFireEV1Surface/FlushMountReaders ____________________________ 6

FlushMountUnit ____________________________________________________________________________ 6

SurfaceMountUnit __________________________________________________________________________ 6

InstallationdiagramforDESFireEV1PanelMountReader _____________________________________ 6

InstallationdiagramforDESFireEV1PanelMountReader _____________________________________ 7

ACTpro DESFIRE EV1 Operating and Installation Manual Rev 1.0

Introduction: about MIFARE DESFire EV1

The ACTpro MIFARE DESFIRE EV1 cards are widely used in areas where security of the data is important.

The technology is used in many areas such as access control, transport, cashless vending and logical access

to name a few and it is an ideal platform for different vendors to store data for different applications. The data

is stored in files, each file having it’s own unique access keys, and the transmission of the data is secured by

the onboard AES hardware cryptographic engine. Each MIFARE DESFire EV1 card has a unique serial

number.

Important Installation Notes

•On the ACTpro MIFARE DESFire EV1 1030 ensure the grey cable is snipped before applying power.

•Check the correct voltage is applied to the reader

•Confirm the required Data output “Clock & Data” or “Wiegand”

•Confirm the required reader File, Serial/reverse Serial.

Ordering Information



DESFire EV1

1030

DESFire EV1

1030PM

DESFire EV1

1040

DESFire EV1

1050

Description MIFARE DESFire

EV1 proximity

reader

MIFARE DESFire

EV1 proximity

reader

MIFARE DESFire EV1

proximity reader

MIFARE DESFire EV1

pin and proximity reader

Mounting Mullion Panel Surface/Flush

Proximity Yes

Pin No Yes

Outputs Clock & Data or

Wiegand 37bit.

Yes

Selectable file, serial &

reverse serial

Yes

Construction Robust polycarbonate housing

Potted Electronics Yes

IP Rating IP 67

Tri-Colour LED Yes

Built-in buzzer Yes

External Buzzer Control No Yes

Operating Voltage 12 - 24 Volt DC

Current Consumption (Typ) 40mA 40mA 70mA 70mA

Current Consumption (Peak) 130mA 70mA 140mA 140mA

Weight 200gms 65g 142g 155g

Dimensions (H * W * D) 108 * 36 * 13 63 * 58 * 23 110 * 100 * 35 110 * 100 * 35

Operating Temperature -10 to +50 Celsius

Ordering Information

Reader Order Codes Description

ACTproEV1 1030 ACTpro MIFARE DESFire EV1 Mullion Proximity reader

ACTproEV1 1030PM ACTpro MIFARE DESFire EV1 Panel mount Proximity reader

ACTproEV1 1040 ACTpro MIFARE DESFire EV1 surface / flush mount Proximity reader

ACTproEV1 1050 ACTpro MIFARE DESFire EV1 surface / flush mount Proximity and Pin reader

Card Order Code

ACTproEV1 Card-B ACT encoded MIFARE DESFIRE EV1 2K ISO Card

ACTpro DESFIRE EV1 Operating and Installation Manual Rev 1.0

Reader Output Data Format

Clock and Data

The default data output format from the ACTpro MIFARE DESFire EV1 readers is Clock and Data encoded as

10 BCD digits (also known as Magnetic Stripe Track2 or ABA).

Wiegand

The reader can be configured to output Wiegand formatted data rather that the default clock & data, by

connecting the Sense line to 0V before powering on the reader, this will switch the unit to 37bit Wiegand

output mode.

Wiring Information for “Clock & Data” Output

The standard Clock & Data wiring colours for ACTpro MIFARE DESFire EV1 readers are shown below.

Reader PIN Description Recommended wiring colour Description

Sense White Direction – connect for entry

Clock / D1 Green Clock / D1

Data / D0 Blue Data / D0

12-24 V DC Red + Voltage

0 V Black - Voltage

Red Brown Red LED

Green Yellow Green LED

Wiring for Entry / Exit “Clock and Data” Readers

Wiring for “Clock & Data” Entry Reader

Colour Controller Pin

White Sense

Green CLOCK / D1

Blue DATA / D0

Red +12V

Black 0V

Brown RED

Yellow GREEN

Wiring for “Clock & Data” Exit Reader

Colour Controller Pin

White DO NOT CONNECT

Green CLOCK / D1

Blue DATA / D0

Red +12V

Black 0V

Brown RED

Yellow GREEN

ACTpro DESFIRE EV1 Operating and Installation Manual Rev 1.0

Wiring Information for “Wiegand” Output

The standard Wiegand wiring colours for ACTpro MIFARE DESFire EV1 readers are shown below.

Reader PIN Description Recommended wiring colour Description

Sense White Direction – connect for entry

Clock / D1 Green Clock / D1

Data / D0 Blue Data / D0

12-24 V DC Red + Voltage

0 V Black - Voltage

Red Brown Red LED

Green Yellow Green LED

Wiring for Entry / Exit “Wiegand” Readers

Wiring for “Wiegand” Entry Reader

Colour Controller Pin

White 0V

Green CLOCK / D1

Blue DATA / D0

Red +12V

Black 0V

Brown RED

Yellow GREEN

Wiring for “Wiegand” Exit Reader

Colour Controller Pin

White 0V

Green CLOCK / D1

Blue Sense

Red +12V

Black 0V

Brown RED

Yellow GREEN

ACTpro DESFIRE EV1 Operating and Installation Manual Rev 1.0

Reader Configuration

About DESFire EV1 File operation

The default operation of all ACTpro MIFARE DESFire EV1 readers configured for file operation, to read the

number that is encoded in a file on the ACT MIFARE DESFire EV1 cards, the number is also printed on the

cards.

About Serial and Reverse Serial operation

When in Serial or reverse serial mode the MIFARE DESFire EV1 card serial number is read by the reader.

Operation: ACTpro MIFARE DESFire EV1 1030PM / 1040 / 1050

The ACTpro MIFARE DESFire EV1 readers can be configured to operate in file operation mode (the default)

or as a serial/reverse serial reader which is selectable via a jumper.

The default position of the jumper is set for file operation (jumper on pins 1 and 2). To change the operation

power down the reader, change the jumper for the desired operation and then reapply power.

DESFire EV1 File Serial Reverse Serial

Connect pins 1&2

Connect pins 2&3

Do NOT connect Jumper

Jumper selects 1 of 3 modes

1. DESFire EV1 File operation

2. Serial number operation

3. Reverse Serial number operation

Operation: ACTpro MIFARE DESFire EV1 1030

The operation of the ACTpro DESFire EV1 1030 is selectable via cable configuration, the default setting is File

operation where both Orange and Purple cables are connected to 0V. To change the operation power down

the reader, change the Orange and Purple cable for the desired operation and then reapply power.

Colour DESFire EV1 File Serial Reverse Serial

Orange 0V 0V Not Connected

Purple 0V Not Connected 0V

ACTpro DESFIRE EV1 Operating and Installation Manual Rev 1.0

Backlight Operation

The ACTpro MIFARE DESFire EV1 1050 has backlight illumination of the keypad.

Status LED operation on ACTpro MIFARE DESFire EV1 1030PM reader only

The status LED can be disabled via jumpers on the ACTpro MIFARE DESFire EV1 1030PM only, the default

operation is ON. The status LED is blue when in standby mode and goes Green or Red for access granted or

Access Denied. When the status if OFF the LED is off and goes Green or Red for access granted or Access Denied.

Reader Inputs

The Internal buzzer is activated by applying 0V to the Buzz PIN. The buzzer activates 4 seconds after the 0V is

applied and sounds continuously until the 0V is removed, buzzer Control not available on the ACTpro MIFARE

DESFire EV1 1030 reader.

The Red and Green LEDs are activated by applying 0V to the respective Red and Green input pins.

Power On Beep Codes

The Output Data Format and File or Serial Operation of the reader can be determined by the beeps generated by the

reader after power is applied. The reader will generate two sets of beeps, the first indicating the Output Data Format

and the second set of beeps indicating file or Serial Operation. The first set of beeps will occur while the LED is

Green, the second set of beeps occur half a second later while the LED is Blue.

First Beep Set Double Beep DESFire EV1 File Reader

Single Beep Serial Reader

Triple Beep Serial Reader (byte reverse)

Second Beep Set Double Beep Clock & Data Output

Single Beep Wiegand 37 bit Output

ACTpro DESFIRE EV1 Operating and Installation Manual Rev 1.0

Installation diagram for DESFire EV1 Surface / Flush Mount Readers

Flush Mount Unit

Surface Mount Unit

ACTpro DESFIRE EV1 Operating and Installation Manual Rev 1.0

Installation diagram for DESFire EV1 Panel Mount Reader

ACT ACTPRO MIFARE DESFIRE EV1 1050 Operating instructions

Brand: ACT

Model: ACTPRO MIFARE DESFIRE EV1 1050

Type: Operating instructions

This manual is also suitable for

Download PDF

report

ACT ACTPRO MIFARE DESFIRE EV1 1050 Operating instructions

This manual is also suitable for

ACT ACTPRO MIFARE DESFIRE EV1 1050 Operating instructions

Related papers

Other documents