ESAB EPP-200 Precision Plasmarc Cutting Console User manual
- Category
- Welding System
- Type
- User manual
77
EPP-200
Precision Plasmarc Cutting Console
0558004943
Instruction Manual (GB)
These INSTRUCTIONS are for experienced operators. If you are not fully familiar with the principles
of operation and safe practices for arc welding and cutting equipment, we urge you to read our booklet,
"Precautions and Safe Practices for Arc Welding, Cutting, and Gouging," Form 52-529. Do NOT permit
untrained persons to install, operate, or maintain this equipment. Do NOT attempt to install or operate
this equipment until you have read and fully understand these instructions. If you do not fully
understand these instructions, contact your supplier for further information. Be sure to read the Safety
Precautions before installing or operating this equipment.
BE SURE THIS INFORMATION REACHES THE OPERATOR.
YOU CAN GET EXTRA COPIES THROUGH YOUR SUPPLIER.
USER RESPONSIBILITY
This equipment will perform in conformity with the description thereof contained in this manual and accompanying
labels and/or inserts when installed, operated, maintained and repaired in accordance with the instructions provided.
This equipment must be checked periodically. Malfunctioning or poorly maintained equipment should not be used.
Parts that are broken, missing, worn, distorted or contaminated should be replaced immediately. Should such repair
or replacement become necessary, the manufacturer recommends that a telephone or written request for service
advice be made to the Authorized Distributor from whom it was purchased.
This equipment or any of its parts should not be altered without the prior written approval of the manufacturer. The
user of this equipment shall have the sole responsibility for any malfunction which results from improper use, faulty
maintenance, damage, improper repair or alteration by anyone other than the manufacturer or a service facility
designated by the manufacturer.
79
SECTION TITLE PAGE
SECTION 1 SAFETY .................................................................................................................................. 81
SECTION 2 DESCRIPTION ........................................................................................................................................................83
SECTION 3 INSTALLATION ......................................................................................................................................................89
SECTION 4 OPERATION ............................................................................................................................................................97
TABLE OF CONTENTS
80
TABLE OF CONTENTS
Full responsibility for safety of personnel working on or near system rests on user of ESAB Welding
Equipment.
Wrong operation can lead to abnormal situation, injure operator and damage equipment.
All personnel working with welding equipment must be fully familiar with
- handling of equipment
- location of emergency stops
- functions of equipment
- applicable safety regulations
- cutting
Operator must make sure
- no one stays inside work area while machine starts
- no one is unprotected while arc is being struck
Work area must be
- free of machine parts, tools and other objects that can obstruct operator moving within area
- so arranged, that emergency stop buttons are easily accessible
- free from draughts
Personal safety equipment
- always use proper safety equipment such as goggles, non flammable clothing, protective gloves
- never wear loose clothing, belts, bracelets, rings etc., which may catch on equipment or cause burns
Miscellaneous
- only authorised personnel may operate electrical equipment
- check whether return cables are properly fitted and earthen
- requisite fire fighting equipment should be easily available in specially and clearly marked areas
- lubrication and maintenance of welding equipment must not be proceeded during operation.
SECTION 1 SAFETY
! WARNING !
ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE
PRECAUTIONS WHEN WELDING OR CUTTING. ASK YOUR EMPLOYER FOR SAFETY PRACTICES
THAT SHOULD BE BASED ON MANUFACTURER’S HAZARD DATA.
ELECTRIC SHOCK - Can kill
- Install and earth welding equipment in accordance with obligatory standards.
- Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothes.
- Insulate yourself from earth and workpiece.
- Ensure your work position is safe.
FUMES AND GASES - Can be dangerous to your health
- Keep your head away from fumes.
- Use ventilation and/or extraction to keep fumes and gases away from your breathing zone and surroundings.
ARC RAYS - Can injure eyes and burn skin
- Protect your eyes and skin. Use correct welding screens, filter lens and wear protective clothes.
- Protect bystanders with suitable screens or curtains.
FIRE HAZARD
- Sparks (spatter) can cause fire. Make therefore sure there are no inflammable materials nearby.
NOISE - Excessive noise can damage your hearing.
- Protect your ears. Use ear defenders or other hearing protection.
- Warn bystanders of the risk.
MALFUNCTION - Call expert assistance in event of malfunction.
READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING UNIT
PROTECT YOURSELF AND OTHERS !
SECTION 1 SAFETY
83
SECTION 2 DESCRIPTION
The EPP-200 Power Console is designed for mechanized plasma
applications. It can be used with other ESAB products such as the
PT-24 and PT-600 torches, an optional plumbing box and a remote
set-up pendant.
• 50 to 200 Amperes cutting current range
• Forced air cooled
• Solid state DC power
• Integral water cooler
• Input voltage protection
• Local or remote front panel control
• Thermal switch protection for main transformer and
power semiconductor components
• LED status troubleshooting
2.1 Introduction
2.2 General Specifi cations
EPP-200 Power Console (0558004315):
OUTPUT (100% duty cycle)
Voltage ......................................................................................................... 160VDC
Current range DC ................................................................................. 50A to 200A
Power ................................................................................................. 8000 W to 32000 W
Open Circuit Voltage (OCV) .................................................................. 325VDC
INPUT
Voltage (3-phase) .............................................................. 200/230/380/415/460/575 Volts
Current (3-phase) ...............................................................115/100/60/55/50/40 Amperes
Frequency ....................................................................................................50/60Hz
KVA ................................................................................................................. 39.8 kW
Power ............................................................................................................. 37.8 kW
Power Factor ...................................................................................................95%
Input Fuse .................................................................................. See Section 3, Installation
84
Electric Shock Can Kill!
Use of torches not designed for this console could result in a haz-
ardous electric shock.
Use only torches designed for the EPP-200 Console.
WARNING
2.3 Dimensions and Weight
44 in. (1100mm)
42in. (1050mm)
22in. (550mm)
Weight = 725 lbs. (330 kg)
SECTION 2 DESCRIPTION
85
2.4 EPP-200 Options and Accessories
Options
5 ft. (1.5m)
10 ft. (3.0m)
20 ft. (6.1m)
25 ft. (7.6m)
30 ft. (9.1m)
40 ft. (12.2m)
50 ft. (15.2m)
75 ft. (22.9m)
100 ft. (30.5m)
125 ft. (38.1m)
150 ft. (45.7m)
Cooling Water Hoses (2)
Console to Plumbing Box
Control Cable
Plumbing Box to Console
Pilot Arc Lead
Plumbing Box to Console
Power Lead
Console to Plumbing Box
0558003979
0558003980
0558003981
33132
0558003982
0558003983
33133 (4495019)
33134 (4495020)
33135 (4495021)
33136 (4495022)
0558003984
N / A
N / A
N / A
0558004651
N / A
N / A
0558004652
0558004653
0558004654
0558003978
0558004655
0558003985
0558003986
0558003987
33303
0558003988
0558003989
33304 (4495034)
33305 (4495035)
33306 (4495036)
33307 (4495037)
0558003990
0558003991
0558003992
0558003993
22001 (4495038)
0558003994
0558003995
22002 (4495039)
22003 (4495040)
22004 (4495041)
22005 (4495042)
0558003996
SECTION 2 DESCRIPTION
NOTE:
Part Numbers in parenthesis apply to "CE"/European units only.
86
2.5 Gas Hoses
Gas Type 25 ft. 50 ft. 75 ft. 100 ft. 125 ft.
(7.6m) (15.2m) (22.8m) (30.4m) (38.1m)
Nitrogen (clear) 33122 33123 33124 33125 33126
Oxygen (clear - USA) 33117 33118 33119 33120 33121
Oxygen (blue - Euro) 0558002973 0558002974 0558002975 0558002976 0558002977
Argon/Hydrogen (H-35) (1) 33122* 33123* 33124* 33125* 33126*
Air (clear - USA) 33122** 33123** 33124** 33125** 33126**
Air (black - Euro) (2) 0558002978** 0558002979** 0558002980** 0558002981** 0558002982**
Note: * = Requires adapter P/N 19X54 (4494001) (order separately)
** = Requires adapter P/N 74S76 (0558004057) (order separately)
2.6 Gas Regulators
Station Regulator Cylinder Regulator
Nitrogen .....................................................19155 ............................................998343
Oxygen .......................................................19151 .............................................998336
Argon/Hydrogen (H-35) .......................19153 .............................................998341
Air .................................................................30338 (4492008) ......................N/A
A separate start gas regulator is always required:
• For air plasma use air start gas.
• For oxygen or nitrogen use nitrogen start gas.
• For H-35 (argon/hydrogen) H-35 or nitrogen start gas.
A total of 3 regulators will be required (plasma, start and
secondary).
When using a plumbing box:
• Gas hoses from supply cylinders go directly to the
plumbing box.
• Console gas manifold is not used.
NOTICE
NOTICE
SECTION 2 DESCRIPTION
NOTE:
Part Numbers in parenthesis apply to "CE"/European units only.
87
2.7 Basic Packages
The EPP-200 system is available as a pre-engineered package or can
be ordered as individual parts as listed.
Basic Packages include:
• EPP-200 Console
• Plasma Torch
• Appropriate regulators for the gases indicated
• Gas hoses from regulators to console
• Torch coolant
Torch Coolant (25%) – 1 gallon (3.8 L) P/N 0558004297
25% PG coolant improves electrode life in applications using oxygen or
air cut gas but only provides freeze protection down to 13° F (-10.6° C)
Torch Coolant (50%) – 1 gallon (3.8 L) P/N 156F05 (7810012)
50% EG coolant provides freeze protection down to -40° F
(-40.0° C)
SECTION 2 DESCRIPTION
NOTE:
Part Numbers in parenthesis apply to "CE"/European units only.
88
SECTION 2 DESCRIPTION
89
SECTION 3 INSTALLATION
3.1 General
Failure To Follow Instructions Could Lead To Death,
Injury Or Damaged Property
Follow these instructions to prevent injury or property damage.
You must comply with local, state and national electrical and safety
codes.
WARNING
Use Lifting Eye When Hoisting From Overhead
Use safe practices when transporting with overhead method.
Unit weighs over 700 lbs (318 kg). Use approved straps or cables
in good condition.
CAUTION
3.2 Unpacking
• Inspect for transit damage immediately upon receipt.
• Remove all components from shipping container and
check for loose parts in container.
• Inspect louvers for air obstructions.
90
WARNING
CAUTION
CAUTION
Do Not Restrict Air Flow
Restricting intake air with any type of fi lter on or around the Plasma
console will result in overheating and may void the warranty.
3.3 Placement
• A minimum of 2 ft. (0.61m) clearance for cooling air fl ow.
• Plan for top panel and side panels having to be removed
for maintenance, cleaning and inspection.
• Locate the EPP-200 relatively close to a properly fused
electrical power supply.
• Keep area beneath power source clear for cooling air
fl ow.
• Environment should be relatively free of dust, fumes and
excessive heat. These factors will aff ect cooling
effi ciency.
Conductive Dust And Dirt Inside Power Source May
Cause Arc Flash Over
Equipment damage may occur. Electrical shorting may occur if
dust is allowed to buildup inside power source. See maintenance
section.
Electric Shock Can Kill!
Provide maximum protection against electrical shock.
Before any connections are made inside the machine, open the
line wall disconnect switch to turn power off .
3.4 Input Connections to Console
Plasma
Console
SECTION 3 INSTALLATION
91
NOTICE
3.4.1 Primary Power Specifi cations
EPP-200 is a 3-phase unit. Input power must be provided from a line
(wall) disconnect switch that contains fuses or circuit breakers in
accordance to local or state regulations.
Recommended input conductor and line fuse sizes:
Dedicated power line may be necessary.
EPP-200 is equipped with line voltage compensation but to avoid
impaired performance due to an overloaded circuit, a dedicated
power line may be required.
* Sizes per National Electrical Code for a 75° C (165° F) rated copper
conductors @ 40° C (104° F) ambient. Not more than four conductors
in raceway or cable. Local codes should be followed if they specify sizes
other than those listed above. Input current values given in this table
are at maximum output power (40kW) 200 amps at 200VDC.
Rated Load Input and Time delay
Ground Fuse size
Volts Amperes conductor* (amperes)
CU/AWG
200/208 140 2/0 200
230 121 1/0 150
380 74 No.2 100
415 66 No.4 100
460 62 No.4 100
575 48 No.6 70
SECTION 3 INSTALLATION
92
3.4.2 Primary Power Hookup Procedure
The following procedure explains the proper installation steps for
connecting primary electrical power to the plasma console.
NOTE: Safety codes specify the power ground wire be the last
connection to break should the cable be pulled out of the unit.
When preparing the cable for connection, make the ground wire
6 inches (152mm) longer than the three pr primary wires.
1. Ensure input power cable is disconnected from all electrical
sources.
2. Remove right side panel (as viewed from front of console).
3. Route input power cable through the strain relief located at the rear
panel.
4. Pull input power cable through the strain relief to allow cable wires
suffi cient length to connect to main contactor. Tighten strain relief to
ensure input power cable is secured.
5. Connect input power cable ground wire to the ground lug provided
above TB2 (7 position terminal block).
6. Connect three power leads of input power cable to terminals located
atop the main contactor. Secure the leads by tightening each screw.
7. Connect jumper power cables from bottom of the main contactor
to proper input voltage marked on auto transformer. Unit is factory set
for 575V as shown at the left.
8. Connect jumper on TB2 to proper input voltage. This 7 position
terminal block jumper is factory set to 575V.
Input Power Jumper Connection
Ensure each input power jumper cable is connected to correct input
voltage on autotransformer and on TB2.
Factory wired for 575 Volts
CAUTION
Input Power Cable
Strain Relief
Main
Contactor
Ground
Connection
7 Position
Terminal
Block
Auto
Transformer
Factory wired
for 575 volts
SECTION 3 INSTALLATION
93
9. Connect input conductors to line (wall) disconnect.
10. Replace side panel. Replace only if all connections have made.
Output connections require this panel to be removed.
11. Connect the other end of work cable to workpiece or cutting table.
Connection must be made to a clean, exposed metal surface, free of
paint, rust, mill scale, etc.
Electric Current Is Hazardous.
It is important to have a good earth ground connected to the
workpiece or cutting table.
WARNING
Work ground to work piece
Work ground to cutting table
SECTION 3 INSTALLATION
94
3.5 Connecting Plasma Torches to EPP-200 Console and Options
3.5.1 EPP-200 Output Cables, Hoses and Adapters (customer supplied)
EPP-200:
Lengths vary depending on system.
• Coolant Return
• Coolant Supply
• Pilot Arc Cable
• Electrode Cable
• Shield Gas (directly to the Plumbing Box)
• Start Gas (directly to the Plumbing Box)
• Cut Gas (directly to the Plumbing Box)
• Work Cable
• Pendant Cable (if pendant option is ordered)
See Description, Section 2 for part numbers.
A remote SETUP Panel option is available on Avenger 1 and larger ESAB
cut cutting machines. This panel operates the same as the pendant.
Refer to your machine manual for replacement parts.
SECTION 3 INSTALLATION
95
Commercial Antifreeze Will Cause Torch To
Malfunction.
Use special torch coolant.
Do to high electrical conductivity, DO NOT use tap water or
commercial automotive type antifreeze for torch cooling. A specially
formulated torch coolant is REQUIRED. This coolant also protects
from freezing to -34° C (-29° F).
Operating the unit without coolant will cause permanent damage
to the coolant pump.
Check coolant level frequently.
Remove coolant fi ll cap at front console and fi ll coolant tank with 4
gallons (15 liters) of plasma torch coolant.
• Do not fi ll above indicated maximum level.
• Reinstall cap.
CAUTION
Electric Current Is Hazardous.
It is important to have a good earth ground connected to the
workpiece or cutting table.
WARNING
3.6 Coolant Installation
Coolant Fill Cap
SECTION 3 INSTALLATION
96
SECTION 3 INSTALLATION
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
ESAB EPP-200 Precision Plasmarc Cutting Console User manual
- Category
- Welding System
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ESAB EPP-200 Precision Plasmarc Cutting System User manual
-
-
ESAB EPP-200 Precision Plasmarc Cutting Console User manual
-
-
-
-
-
-
-
