WAGO 2DI 220V DC 3.0ms User manual

Type
User manual
Pos: 2 /Dokumentation al lgemein/Einband/Ei nband Handbuch - Fr ontseite 2015 - mit DocVariab len (Standard) @ 9\mod_1285 229289866_0.doc x @ 64941 @ @ 1
WAGO-I/O-SYSTEM 750
Manual
750-407
2DI 220V DC 3.0ms
2-Channel Digital Input Module 220 VDC;
2-to 4-Conductor Connection; High-
side Switching
Version 1.0.0
Pos: 3 /Alle Serien (Al lgemeine Module)/Hin weise zur Dokumentation/I mpressum für Standar dhandbücher - allg. Angaben, Anschrif ten, Telefonnummern und E-Mai l-Adress en @ 3\mod_1219151118203_21. docx @ 21060 @ @ 1
2 WAGO-I/O-SYSTEM 750
750-407 2DI 220V DC 3.0ms
Manual
Version 1.0.0
© 2016 by WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: +49 (0) 571/8 87 – 0
Fax: +49 (0) 571/8 87 – 1 69
Web: http://www.wago.com
Technical Support
Phone: +49 (0) 571/8 87 – 5 55
Fax: +49 (0) 571/8 87 – 85 55
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
=== Ende der Liste für Textmarke Einband_vorne ===
WAGO-I/O-SYSTEM 750 Table of Contents 3
750-407 2DI 220V DC 3.0ms
Manual
Version 1.0.0
Pos: 5 /Dokumentation al lgemein/Verzeic hnisse/Inhaltsverzei chnis - Überschrif t oG und Verzeichnis @ 3\mod_1219 151230875_21.doc x @ 21063 @ @ 1
Table of Contents
1 Notes about this Documentation ................................................................. 5
1.1 Validity of this Documentation ................................................................. 5
1.2 Copyright ................................................................................................... 5
1.3 Symbols ..................................................................................................... 6
1.4 Number Notation ....................................................................................... 8
1.5 Font Conventions ...................................................................................... 8
2 Important Notes ........................................................................................... 9
2.1 Legal Bases ............................................................................................... 9
2.1.1 Subject to Changes ............................................................................... 9
2.1.2 Personnel Qualifications ....................................................................... 9
2.1.3 Use of the WAGO-I/O-SYSTEM 750
in Compliance with Underlying Provisions ......................................... 9
2.1.4 Technical Condition of Specified Devices ......................................... 10
2.2 Safety Advice (Precautions) .................................................................... 11
3 Device Description ..................................................................................... 13
3.1 View ........................................................................................................ 15
3.2 Connectors ............................................................................................... 16
3.2.1 Data Contacts/Internal Bus ................................................................. 16
3.2.2 Power Jumper Contacts/Field Supply ................................................ 17
3.2.3 CAGE CLAMP
®
Connectors ............................................................. 19
3.3 Display Elements .................................................................................... 20
3.4 Operating Elements ................................................................................. 20
3.5 Schematic Diagram ................................................................................. 21
3.6 Technical Data ........................................................................................ 22
3.6.1 Device Data ........................................................................................ 22
3.6.2 Power Supply...................................................................................... 22
3.6.3 Communication .................................................................................. 22
3.6.4 Inputs .................................................................................................. 22
3.6.5 Climatic Environmental Conditions ................................................... 23
3.6.6 Connection Type ................................................................................ 23
3.7 Approvals ................................................................................................ 24
3.8 Standards and Guidelines ........................................................................ 24
4 Mounting ..................................................................................................... 25
4.1 Mounting Sequence ................................................................................. 25
4.2 Inserting and Removing Devices ............................................................ 26
4.2.1 Inserting the I/O Module .................................................................... 26
4.2.2 Removing the I/O Module .................................................................. 27
5 Connect Devices ......................................................................................... 28
5.1 Connecting a Conductor to the CAGE CLAMP
®
................................... 28
5.2 Connection Examples .............................................................................. 29
5.2.1 2-Conductor Connection .................................................................... 29
5.2.2 3-Conductor Connection .................................................................... 29
5.2.3 4-Conductor Connection .................................................................... 30
6 Process Image ............................................................................................. 31
4 Table of Contents WAGO-I/O-SYSTEM 750
750-407 2DI 220V DC 3.0ms
Manual
Version 1.0.0
7 Use in Hazardous Environments .............................................................. 32
7.1 Marking Configuration Examples ........................................................... 33
7.1.1 Marking for Europe According to ATEX and IEC-Ex ...................... 33
7.1.2 Marking for America According to NEC 500 .................................... 38
7.2 Installation Regulations ........................................................................... 39
7.2.1 Special Conditions for Safe Use
(ATEX Certificate TÜV 07 ATEX 554086 X) .................................. 40
7.2.2 Special Conditions for Safe Use
(ATEX Certificate TÜV 12 ATEX 106032 X) .................................. 41
7.2.3 Special Conditions for Safe Use
(IEC-Ex Certificate TUN 09.0001 X) ................................................ 42
7.2.4 Special Conditions for Safe Use
(IEC-Ex Certificate IECEx TUN 12.0039 X) .................................... 43
7.2.5 Special Conditions for Safe Use
According to ANSI/ISA 12.12.01 ...................................................... 44
List of Figures ...................................................................................................... 45
List of Tables ........................................................................................................ 46
=== Ende der Liste für Textmarke Verzeichnis_ vorne ===
WAGO-I/O-SYSTEM 750 Notes about this Documentation 5
750-407 2DI 220V DC 3.0ms
Manual
Version 1.0.0
Pos: 7 /Alle Serien (Al lgemeine Module)/Über schriften/Neue Über schriften/Ebene 1 Hinweise zu dieser Doku mentation - Überschri ft 1 @ 4\mod_1237987661750_21. docx @ 29029 @ 1 @ 1
1 Notes about this Documentation
Pos: 8 /Alle Serien (Al lgemeine Module)/Hin weise zur Dokumentation/ Hinweise/Hinwei s: Dokumentation aufbe wahren @ 4\mod_1237987 339812_21.docx @ 29026 @ @ 1
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation is
included, if necessary.
Pos: 9 /Alle Serien (Al lgemeine Module)/Über schriften/Neue Übersc hriften/Ebene 2Gül tigkeitsbereic h - Überschrift 2 @ 12\mod_13389 12448776_21.doc x @ 96469 @ 2 @ 1
1.1 Validity of this Documentation
Pos: 10 /Serie 750 (W AGO-I/O-SYSTEM)/Hinweise zur Dokumenta tion/Gültigkeitsber eich/Gültigkeit sbereich Dokumenta tion Busklemme 750-xxxx, ohne Variantenangabe @ 14\ mod_1358944037947_2 1.docx @ 109346 @ @ 1
This documentation is only applicable to the I/O module 750-407
(2DI 220V DC 3.0ms).
Pos: 11 /Serie 750 (W AGO-I/O-SYSTEM)/Hinweise zur Dokumenta tion/Hinweise/Acht ung: Hinweis zur Dokume ntation Busklemmen 750- xxxx @ 4\mod_1237986979 656_21.docx @ 29023 @ @ 1
The I/O module 750-407 shall only be installed and operated according to the
instructions in this manual and in the manual for the used fieldbus
coupler/controller.
Consider power layout of the WAGO-I/O-SYSTEM 750!
In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler/controller, which can be downloaded at www.wago.com.
There, you can obtain important information including information on electrical
isolation, system power and supply specifications.
Pos: 12.1 /Alle Serien (A llgemeine Module)/Hin weise zur Dokumentatio n/Urheberschut z ausführlich @ 4\mod_123 5565145234_21.doc x @ 27691 @ 2 @ 1
1.2 Copyright
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos: 12.2 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_12211 08045078_0.doc x @ 21810 @ @ 1
6 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-407 2DI 220V DC 3.0ms
Manual
Version 1.0.0
Pos: 12.3 /Alle Serien (A llgemeine Module)/Ü berschriften/Neue Überschriften/Eben e 2Symbole - Überschr ift 2 @ 13\mod_1351068042408 _21.docx @ 105270 @ 2 @ 1
1.3 Symbols
Pos: 12.4.1 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweis e/Gefahr/Gefahr: _W arnung vor Personenschäden a llgemein_ - Erläuter ung @ 13\mod_1343309450020_ 21.docx @ 101029 @ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12.4.2 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Gefahr/Gefahr: _W arnung vor Personenschäden dur ch elektrischen Stro m_ - Erläuterung @ 13\mod_134 3309694914_21.doc x @ 101030 @ @ 1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12.4.3 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Warnung/Warnung: _Warnung vor Personenschäd en allgemein_ - Erläuter ung @ 13\mod_134330987704 1_21.docx @ 101035 @ @ 1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos: 12.4.4 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Vorsicht/Vorsi cht: _Warnung vor Personen schäden allgemein_ - Erläuterung @ 13\mod_1343310 028762_21.doc x @ 101038 @ @ 1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos: 12.4.5 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: _W arnung vor Sachschäden al lgemein_ - Erläuteru ng @ 13\mod_1343310134623_21. docx @ 101041 @ @ 1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12.4.6 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: _W arnung vor Sachschäden dur ch elektrostatische Auf ladung_ - Erläuter ung @ 13\mod_13433102277 02_21.docx @ 101044 @ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12.4.7 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweis e/Hinweis/Hinweis: _W ichtiger Hinweis al lgemein_ - Erläuterun g @ 13\mod_1343310326906_21. docx @ 101047 @ @ 1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos: 12.4.8 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Information/I nformation: _Wei tere Information allgemein_ - Erläuterung @ 13\mod_134 3310439814_21.doc x @ 101051 @ @ 1
WAGO-I/O-SYSTEM 750 Notes about this Documentation 7
750-407 2DI 220V DC 3.0ms
Manual
Version 1.0.0
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos: 12.5 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_12211 08045078_0.docx @ 21810 @ @ 1
8 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-407 2DI 220V DC 3.0ms
Manual
Version 1.0.0
Pos: 12.6 /Alle Serien (A llgemeine Module)/Hin weise zur Dokumentati on/Darstellung der Zahlensysteme - Übersc hrift 2 und Inhalt @ 3\mod_122 1059454015_21.doc x @ 21711 @ 2 @ 1
1.4 Number Notation
Table 1: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated with
dots (.)
Pos: 12.7 /Alle Serien (A llgemeine Module)/Hin weise zur Dokumentatio n/Schriftkon ventionen - Überschri ft 2 und Inhalt @ 3\mod_122105952143 7_21.docx @ 21714 @ 2 @ 1
1.5 Font Conventions
Table 2: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.: Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.: [F5]
Pos: 13 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Important Notes 9
750-407 2DI 220V DC 3.0ms
Manual
Version 1.0.0
Pos: 14 /Alle Serien ( Allgemeine Module)/ Überschriften/Neue Übersc hriften/Ebene 1W ichtige Erläuterunge n - Überschrift 1 @ 4\ mod_1241428899156_21.d ocx @ 32170 @ 1 @ 1
2 Important Notes
Pos: 15.1 /Alle Serien (A llgemeine Dokumente) (Allgemeine Module)/ Wichtige Erläuterunge n/Wichtige Erläut erungen - Einleitun g @ 3\mod_1221059818031_21. docx @ 21717 @ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos: 15.2 /Alle Serien (A llgemeine Module)/Ü berschriften/Neue Überschriften/Eben e 2Rechtliche Grundlag en - Überschrift 2 @ 3\mod_1 221060626343_21.doc x @ 21726 @ 2 @ 1
2.1 Legal Bases
Pos: 15.3 /Alle Serien (A llgemeine Dokumente) (Allgemeine Module)/ Wichtige Erläuter ungen/Änderungsvorb ehalt - Überschri ft 3 und Inhalt @ 3\mod_12210600364 84_21.docx @ 21720 @ 3 @ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications that serve to increase the efficiency of technical
progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from
the granting of patents or from the legal protection of utility patents. Third-party
products are always mentioned without any reference to patent rights. Thus, the
existence of such rights cannot be excluded.
Pos: 15.4 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Personalqua lifikationPerson alqualifikation 750- xxxx - Überschri ft 3 und Inhalt @ 3\mod_12240612080 46_21.docx @ 24063 @ 3 @ 1
2.1.2 Personnel Qualifications
All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos: 15.5 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Bestimmungsge mäße VerwendungBes timmungsgemäße Verwendun g 750-xxxx - Überschri ft 3 und Inhalt @ 3\mod_12240641512 34_21.docx @ 24070 @ 3 @ 1
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with
Underlying Provisions
Fieldbus couplers, fieldbus controllers and I/O modules found in the modular
WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and
transmit them to actuators or higher-level control systems. Using programmable
controllers, the signals can also be (pre-) processed.
The devices have been developed for use in an environment that meets the IP20
protection class criteria. Protection against finger injury and solid impurities up to
12.5 mm diameter is assured; protection against water damage is not ensured.
Unless otherwise specified, operation of the devices in wet and dusty
environments is prohibited.
Operating the WAGO-I/O-SYSTEM 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information
in the section “Device Description > “Standards and Guidelines” in the manual
for the used fieldbus coupler/controller.
10 Important Notes WAGO-I/O-SYSTEM 750
750-407 2DI 220V DC 3.0ms
Manual
Version 1.0.0
Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-
SYSTEM 750 in hazardous environments. Please note that a prototype test
certificate must be obtained that confirms the correct installation of the system in
a housing or switch cabinet.
Pos: 15.6 /Alle Serien (A llgemeine Dokumente) (Allgemeine Module)/ Wichtige Erläuterunge n/Technischer Zusta nd der Geräte - Übersc hrift 3 und Inhalt @ 3\mod_12210 60446109_21.docx @ 217 23 @ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. WAGO
Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of
changes in hardware or software as well as to non-compliant usage of devices.
Please send your request for modified and new hardware or software
configurations directly to WAGO Kontakttechnik GmbH & Co. KG.
Pos: 15.7 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_12211 08045078_0.docx @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Important Notes 11
750-407 2DI 220V DC 3.0ms
Manual
Version 1.0.0
Pos: 15.8 /Alle Serien ( Allgemeine Module)/Ü berschriften/Neue Überschriften/Eben e 2Sicherheitshin weise - Überschrift 2 @ 6\ mod_1260180299987_21.doc x @ 46724 @ 2 @ 1
2.2 Safety Advice (Precautions)
Pos: 15.9 /Alle Serien (A llgemeine Dokumente) (Allgemeine Module)/ Wichtige Erläuterunge n/Sicherheitshi nweise/Einleitung Si cherheitshin weise Hardware @ 6\mod_1260 180170493_21.doc x @ 46720 @ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 15.10.1 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläu terungen/Sicherhei tshinweise/Gefahr /Gefahr: Nicht an Gerä ten unter Spannung arbei ten! @ 6\mod_1260180365327 _21.docx @ 46727 @ @ 1
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos: 15.10.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Er läuterungen/Sicherhei ts- und sonstige Hin weise/Gefahr/Gefahr: Einbau 0750-xxxx nur in Gehäusen, Schränken oder elektrischen Betri ebsräumen! @ 6\mod_126018 0556692_21.docx @ 46731 @ @ 1
Install the device only in appropriate housings, cabinets or in electrical
operation rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
Pos: 15.10.3 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Gefahr /Gefahr: Unfallver hütungsvorschr iften beachten! @ 6\mod_1260 180657000_21.doc x @ 46735 @ @ 1
Pos: 15.10.4 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Gefahr /Gefahr: Auf normgerec hten Anschluss achten! @ 6\mod_1260180753479_ 21.docx @ 46739 @ @ 1
Pos: 15.11.1 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Achtun g/Achtung: Defekte od er beschädigte Geräte aust auschen! @ 6\mod_126018 0857358_21.doc x @ 46743 @ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.
Pos: 15.11.2 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Achtun g/Achtung: Geräte vor kriechenden und isolier enden Stoffen schütze n! @ 6\mod_126018103621 6_21.docx @ 46747 @ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for handling
devices/modules.
Pos: 15.11.3 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Achtun g/Achtung: Reinigung nur mit zulässigen Materi alien! @ 6\mod_12601812 03293_21.docx @ 46751 @ @ 1
Clean only with permitted materials!
Clean soiled contacts using oil-free compressed air or with ethyl alcohol and
leather cloths.
Pos: 15.11.4 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Achtun g/Achtung: Kein Kontak tspray verwenden! @ 6\ mod_1260181290808_21. docx @ 46755 @ @ 1
12 Important Notes WAGO-I/O-SYSTEM 750
750-407 2DI 220V DC 3.0ms
Manual
Version 1.0.0
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos: 15.11.5 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Achtun g/Achtung: Verpolun g vermeiden! @ 6\mod_1260184 045744_21.doc x @ 46767 @ @ 1
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos: 15.11.6 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Achtun g/Achtung: Elektrosta tische Entladung ver meiden! @ 6\mod_1260181 364729_21.docx @ 46759 @ @ 1
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.
Pos: 16 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Device Description 13
750-407 2DI 220V DC 3.0ms
Manual
Version 1.0.0
Pos: 17 /Alle Serien ( Allgemeine Module)/ Überschriften/Neue Überschriften/Ebene 1G erätebeschreibun g - Überschrift 1 @ 3\mod_123375 6084656_21.doc x @ 27096 @ 1 @ 1
3 Device Description
Pos: 18.1 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/An wendung/DI/Anwendung 7 50-x4x x DI @ 3\mod_12 33762736718_21.doc x @ 27108 @ @ 1
The digital input module 750-407 (2DI 220V DC 3.0ms) receives control signals
from digital field (e.g. of sensors, transmitters, switches or proximity switches).
Pos: 18.2 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/I /O-Beschreibung/DI /I/O-Beschrei bung 750-0407 2 DI 2-/3-/4-Leiter (DI, 220 V, 0 V und Er de) @ 7\mod_1274862216081_21. docx @ 57033 @ @ 1
The I/O module has 2 input channels, providing a direct connection to 2-, 3- or 4-
wire sensors.
The sensors are connected to the following CAGE CLAMP
®
terminals: DI 1,
220 V, 0 V and ground, or DI 2, 220 V, 0 V and ground.
Pos: 18.3 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ei nleitung/I/O-Besc hreibung/Allge mein/Verweis auf Kapit el "Anschlüsse" @ 8\mod_1 276775378035_21.d ocx @ 57956 @ @ 1
The assignment of the connections is described in the “Connectors” section.
Pos: 18.4 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/I /O-Beschreibung/A llgemein/Verweis auf Kapitel "Geräte ansc hließen" > "Anschluss beispiel(e)" @ 5\mod_1 246015203281_21.doc x @ 36298 @ @ 1
Connection examples are shown in section “Connecting Devices” > … >
“Connection Example(s)”.
Pos: 18.5 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/I /O-Beschreibung/DI /I/O-Beschrei bung 750-x4xx DI RC-Filter 3, 0 ms @ 3\mod_1233755071062_21.doc x @ 27080 @ @ 1
Each input channel has a RC noise rejection filter with a time constant of 3.0 ms.
Pos: 18.6 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/LE D-Anzeige/LED Zustan d Signal @ 3\mod_12337552585 78_21.docx @ 27087 @ @ 1
A green LED indicates the switched status of each channel.
Pos: 18.7 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ei nleitung/LED-Anzei ge/Verweis auf Kapi tel "Anzeigeelemente" @ 5\mod_1246010525000_2 1.docx @ 36194 @ @ 1
The meaning of the LEDs is described in the “Display Elements” section.
Pos: 18.8 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Sicherheits- und sonstige Hinweise/ Hinweis/Hinweis: Einspeiseklemme f ür Versorgung ungleic h 24 V einsetzen @ 5\mod_12470326093 40_21.docx @ 36784 @ @ 1
Only connect to I/O modules with the same field power supply!
The I/O module 750-407 requires a field supply not equal to 24 VDC.
Therefore, this I/O module 750-407 shall only be connected to modules having
the same field power supply.
If using an adjacent I/O module designed for another field power supply, place an
appropriate supply module between this adjacent module and the I/O module 750-
407.
Failure to observe these instructions may result in damage to properties or injuries
to people.
Pos: 18.9 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/Ver sorgung/Versorgung DC 220 V, 0 V, Erde über Lei stungskontakte @ 5\mod_1246870 311688_21.doc x @ 36640 @ @ 1
The I/O module receives the 220 VDC potential, the 0 V potential and the earth
potential for the field level from an upstream I/O module via the power contacts
used as blade contacts. It then provides this potential to subsequent I/O modules
via the power contacts used as spring contacts.
Pos: 18.10 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: M aximaler Strom Leistungsk ontakte 10 A @ 3\mod_122649 9143500_21.doc x @ 25029 @ @ 1
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded. If
exceeded, insert an additional supply module.
Pos: 18.11 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/Ver sorgung/Galvanisc he Trennung Feld/Syst em @ 3\mod_1233756478 750_21.docx @ 27102 @ @ 1
The field voltage and the system voltage are electrically isolated from each other.
Pos: 18.12 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/Ver sorgung/Anordn ung unter Berücksichti gung der Leistungskon takte beliebig @ 3\mod_12 33756233468_21.doc x @ 27099 @ @ 1
With consideration of the power jumper contacts, the individual modules can be
arranged in any combination when configuring the fieldbus node. An arrangement
in groups within the group of potentials is not necessary.
14 Device Description WAGO-I/O-SYSTEM 750
750-407 2DI 220V DC 3.0ms
Manual
Version 1.0.0
Pos: 18.13 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/Ei nsatzbereich/ Einsatzbereich 750-xxxx a lle Koppler/Contr oller ohne Einschr änkung @ 3\mod_1232541691906_21. docx @ 26522 @ @ 1
The I/O module 750-407 can be used with all fieldbus couplers/controllers of the
WAGO-I/O-SYSTEM 750.
Pos: 19 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Device Description 15
750-407 2DI 220V DC 3.0ms
Manual
Version 1.0.0
Pos: 20 /Alle Serien ( Allgemeine Module)/ Überschriften/Neue Übersc hriften/Ebene 2Ansi cht - Überschri ft 2 @ 4\mod_1240984217343_21. docx @ 31958 @ 2 @ 1
3.1 View
Pos: 21 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Ansicht/Digit aleingangsklemmen/ Ansicht 750-0407 @ 7\mod_12 74870318831_21.docx @ 570 70 @ @ 1
Figure 1: View
Pos: 22 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Ansicht/Ansic ht CageClamp®_Legende mi t LEDs, mit 1 Entriegelungs lasche @ 15\mod_1370867 188922_21.doc x @ 122225 @ @ 1
Table 3: Legend for Figure “View”
Description
Details See Section
Marking possibility with Mini-
WSB
---
Status LEDs
“Device Description” > “Display Elements”
Data contacts
“Device Description” > Connectors”
CAGE CLAMP
®
connectors
“Device Description” > Connectors”
Power jumper contacts
“Device Description” > Connectors”
Release tab
“Mounting” > Inserting and Removing
Devices”
Pos: 23 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1
16 Device Description WAGO-I/O-SYSTEM 750
750-407 2DI 220V DC 3.0ms
Manual
Version 1.0.0
Pos: 24 /Alle Serien ( Allgemeine Module)/ Überschriften/Neue Übersc hriften/Ebene 2Ansc hlüsse - Überschri ft 2 @ 4\mod_1240984262656_21. docx @ 31961 @ 2 @ 1
3.2 Connectors
Pos: 25 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anschlüsse/Da tenkontakte/Klem menbus - Überschrif t 3 @ 6\mod_1256294684083_21.d ocx @ 43660 @ 3 @ 1
3.2.1 Data Contacts/Internal Bus
Pos: 26.1 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ansc hlüsse/Datenk ontakte - Feldbuskopp ler/-controller , Abbildung und Beschr eibung @ 3\mod_1231771259187_ 21.docx @ 26002 @ @ 1
Communication between the fieldbus coupler/controller and the I/O modules as
well as the system supply of the I/O modules is carried out via the internal bus. It
is comprised of 6 data contacts, which are available as self-cleaning gold spring
contacts.
Figure 2: Data Contacts
Pos: 26.2 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Sicherheits- und sonstige Hinweise/ Achtung/Achtung: Busklemmen nicht auf Goldf ederkontakte legen! @ 7\mod_1266318463636_ 21.docx @ 50695 @ @ 1
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Pos: 26.3 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Sicherheits- und sonstige Hinweise/ Achtung/Achtung: ESD - Auf gute Erdung der Umgebun g achten! @ 7\mod_1266318538 667_21.docx @ 50708 @ @ 1
Ensure that the environment is well grounded!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the devices, ensure that the environment
(persons, workplace and packing) is well grounded. Avoid touching conductive
components, e.g. data contacts.
Pos: 27 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Device Description 17
750-407 2DI 220V DC 3.0ms
Manual
Version 1.0.0
Pos: 28 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ansch lüsse/Leistungsk ontakte/Feldver sorgung - Überschr ift 3 @ 6\mod_1256294692864_2 1.docx @ 43664 @ 3 @ 1
3.2.2 Power Jumper Contacts/Field Supply
Pos: 29.1 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Sicherheits- und sonstige Hinweise/ Vorsicht/Vorsic ht: Verletzungsgef ahr durch scharf kantige Messerkontakte! @ 6\ mod_1256193279401_ 21.docx @ 43414 @ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury.
Pos: 29.2 /Serie 750 ( WAGO-I/O-SYSTEM)/ Gerätebeschreibung/ Anschlüsse/Leis tungskontakte 3 LK (Messer /Feder) - Einleitung @ 15\ mod_1371723761988 _21.docx @ 123734 @ @ 1
The I/O module 750-407 has 3 self-cleaning power jumper contacts that supply
and transmit power for the field side. The contacts on the left side of the I/O
module are designed as male contacts and the contacts on the right side as spring
contacts.
Pos: 29.3 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Lei stungskontakte 3 LK (Mes ser/Feder) - Abbi ldung @ 7\mod_1266318232808_ 21.docx @ 50691 @ @ 1
Figure 3: Power Jumper Contacts
Pos: 29.4 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Lei stungskontakte 3 LK (Mes ser/Leistungskon takte 3 LK (Messer/Feder ) - Legende (220 V) @ 16\mod_1371 744255053_21.doc x @ 123919 @ @ 1
Table 4: Legend for Figure “Power Jumper Contacts”
Contact
Type
Function
1 Spring contact
Potential transmission (U
v
)
for field supply
2 Spring contact
Potential transmission (0 V)
for field supply
3 Spring contact
Potential transmission (ground)
for field supply
4 Blade contact
Potential feed-in (ground)
for field supply
5 Blade contact
Potential feed-in (0 V)
for field supply
6 Blade contact
Potential feed-in (U
v
)
for field supply
Pos: 29.5 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Sicherheits- und sonstige Hinweise/ Achtung/Achtung: Maximaler Strom Leistun gskontakte 10 A @ 3\mod_1226499 143500_21.doc x @ 25029 @ @ 1
18 Device Description WAGO-I/O-SYSTEM 750
750-407 2DI 220V DC 3.0ms
Manual
Version 1.0.0
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded. If
exceeded, insert an additional supply module.
Pos: 30 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Device Description 19
750-407 2DI 220V DC 3.0ms
Manual
Version 1.0.0
Pos: 31 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anschlüsse/CAGE CLA MP-Anschlüsse - Überschr ift 3 @ 6\mod_1256296337770 _21.docx @ 43674 @ 3 @ 1
3.2.3 CAGE CLAMP
®
Connectors
Pos: 32 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anschlüsse/Digi taleingangsklem men/Anschlüsse 750-0407 @ 8\mo d_1276590571023_21. docx @ 57718 @ @ 1
Figure 4: CAGE CLAMP
®
Connectors
Table 5: Legend for Figure “CAGE CLAMP
®
Connectors”
Channel
Designation
Connector
Function
1
DI 1 1 Input DI 1: Signal voltage
220 V 2 Input DI 1: Sensor supply
0 V 3 Input DI 1: Sensor supply
Ground 4 Input DI 1: Ground
2
DI 2 5 Input DI 2: Signal voltage
220 V 6 Input DI 2: Sensor supply
0 V 7 Input DI 2: Sensor supply
Ground 8 Input DI 2: Ground
Pos: 33 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1
20 Device Description WAGO-I/O-SYSTEM 750
750-407 2DI 220V DC 3.0ms
Manual
Version 1.0.0
Pos: 34 /Alle Serien ( Allgemeine Module)/ Überschriften/Neue Über schriften/Ebene 2Anz eigeelemente - Über schrift 2 @ 4\mod_12409843 90875_21.docx @ 31964 @ 2 @ 1
3.3 Display Elements
Pos: 35 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anzeigeelemente/ Digitaleingangsk lemmen/Anzeigeele mente 750-04xx 2 DI (A gn, Cgn) @ 8\mod_1276591490399_21. docx @ 57738 @ @ 1
Figure 5: Display Elements
Table 6: Legend for Figure “Display Elements
Channel
Designation
LED
State
Function
1 Status DI 1 A
Off
Input DI 1: Signal voltage (0)
Green
Input DI 1: Signal voltage (1)
2 Status DI 2 C
Off
Input DI 2: Signal voltage (0)
Green
Input DI 2: Signal voltage (1)
Pos: 36 /Alle Serien ( Allgemeine Module)/ Überschriften/Neue Übersc hriften/Ebene 2Bedi enelemente - Übersc hrift 2 @ 4\mod_1239191655456_ 21.docx @ 30439 @ 2 @ 1
3.4 Operating Elements
Pos: 37 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Bedienelemente/Bedi enelemente Busk lemme 750-xxxx nicht vorhande n @ 4\mod_1236322031125_2 1.docx @ 28063 @ @ 1
The I/O module 750-407 has no operating elements.
Pos: 38 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

WAGO 2DI 220V DC 3.0ms User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI